Chris Buechler wrote:
Ole Barnkob Kaas wrote:
Hello,
I use pfSense in a number of remote locations. All running on Soekris
4801 platform with the pfSense-1.0.1-Embedded.img.gz image. Sometimes
the box failes to come online after either deliberate or accidental
power cycle.
It complains that volumes was not properly dismounted. After check and
mount files are missing. I assumed that the cf card was mounted read
only to better survice eg. powerfailures. Any reason why they should
be r/w?
There are bugs in 1.0.1 that cause corruption on embedded. Use 1.2RC2
and it won't happen.
Ouch! Well - actually I'm glad it's a known bug in software and not some
weird hw error or flash fault. I've been busy upgrading to 1.2RC2 as
fast as possible, and I now have a good handful net4801's running
1.2RC2. I'm looking forward to try some of the new features when time
permit. The bad news is that one of the net4801's have already failed
whith what seems to be the same type of error. The "good" news is that
the error showed up so quickly :o) Chances are that weeks or months
could have passed before this error showed up.
Dump from console below
Regards,
Ole Kaas
#########################################################################
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p7 #0: Fri Aug 17 18:16:30 EDT 2007
[EMAIL PROTECTED]:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National S
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory = 134217728 (128 MB)
avail memory = 121872384 (116 MB)
wlan: mac acl policy registered
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
RF5413)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem
0xa0000000-0xa000
0fff irq 10 at device 6.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:00:24:c6:64:a4
sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem
0xa0001000-0xa000
1fff irq 10 at device 7.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <MII bus> on sis1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:00:24:c6
sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0xe300-0xe3ff mem
0xa0002000-0xa000
2fff irq 10 at device 8.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <MII bus> on sis2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: 00:00:24:c6:64:a6
Geode GPIO@ = 6100
Geode Soekris net4801 comBIOS ver. 1.28 20050529 Copyright (C) 2000-2005
isab0: <PCI-ISA bridge> port 0x6100-0x613f,0x6200-0x623f at device 18.0
on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0
x177,0x376,0xe000-0xe00f at device 18.2 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
Geode CBA@ 0x6000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge> at device 18.5 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xa0003000-0xa0003fff irq 11
at devic
e 19.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
orm0: <ISA Option ROM> at iomem 0xc8000-0xd0fff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 245MB <SanDisk SDCFB-256 HDX 2.15> at ata0-master PIO4
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense
WARNING: / was not properly dismounted
___
___/ f \
/ p \___/ Sense
\___/ \
\___/
Welcome to pfSense 1.2-RC2 on the 'embedded' platform...
Setting up embedded specific environment... done.
Mounting filesystems...WARNING: /cf was not p
WARNING: R/W mount of / denied. Filesystem is not clean - run fsck
mount: /dev/ufs/pfSense: Operation not permitted
** /dev/ufs/pfSense
** Last Mounted on /
** Root file system
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
2600 files, 53452 used, 60303 free (2791 frags, 7189 blocks, 2.5%
fragmentation)
***** FILE SYSTEM MARKED CLEAN *****
** /dev/ufs/pfSenseCfg (NO WRITE)
** Last Mounted on /cf
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
8 files, 32 used, 1839 free (23 frags, 227 blocks, 1.2% fragmentation)
WARNING: R/W mount of /cf denied. Filesystem is not clean - run fsck
mount: /dev/ufs/pfSenseCfg: Operation not permitted
** /dev/ufs/pfSenseCfg
** Last Mounted on /cf
** Phase 1 - Check Blocks and Sizes
** Phase 2 - Check Pathnames
** Phase 3 - Check Connectivity
** Phase 4 - Check Reference Counts
** Phase 5 - Check Cyl groups
8 files, 32 used, 1839 free (23 frags, 227 blocks, 1.2% fragmentation)
***** FILE SYSTEM MARKED CLEAN *****
done.
Creating symlinks......done.
Launching PHP init system.../libexec/ld-elf.so.1: Shared object
"libcrypto.so.4"
not found, required by "php"
Starting CRON... done.
Executing rc.d items...
Starting /usr/local/etc/rc.d/*.sh...done.
/libexec/ld-elf.so.1: Shared object "libcrypto.so.4" not found, required
by "php
"
Bootup complete
appending output to nohup.out
FreeBSD/i386 (Amnesiac) (console)
Password:
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
