I cannot do that, because the main infrastructured is already built-in.
I mean 192.168.212.0/24 and 172.24.24.0/24, both got ROUTER GW as default
router "today".
I have installed 2xPfsense, plugged in this way
OPT1 in 192.168.212.0/24
OPT2 in 172.24.24.0/24
We have leased a WAN Link, (pfSense WAN interface)
"Tomorrow" we have to change the default gateway for both networks, to point
to pfsense, LoadBalacing with failover, to continue using former link, and
in case the ROUTER GW is down, use the WAN of pfSense as an alternative
ROUTER GW, and inet (172.16.0.2), is managed by third parties, that´s the
reason I cannot plug directly to pfsense
Thank you
Regards
On Tue, Mar 30, 2010 at 4:14 PM, Evgeny Yurchenko <[email protected]>wrote:
> Evgeny Yurchenko wrote:
>
>> Danny wrote:
>>
>>> Hi,
>>>
>>> I'm trying to setup this:
>>>
>>>
>>> ____ ___
>>> ( ) ( )
>>> ( inet ) ( inet )
>>> (____) (____)
>>> |22.22.22.4 |172.16.0.2
>>> | |
>>> | |
>>> |22.22.22.1(WAN) |172.16.0.1
>>> ------------- 172.24.24.12_______|______
>>> ------|pfSense x2 |-----------------------------------| ROUTER GW |
>>> LAN |___________|172.24.24.20 (OPT2) | |____________|
>>> | | |
>>> 192.168.212.20
>>> |192.168.212.254(OPT1) | |
>>> | |172.24.24.0/24 <
>>> http://172.24.24.0/24> |
>>> | |
>>> | |
>>> |_______________________________________________|
>>> |
>>> | 192.168.212.0/24 <
>>> http://192.168.212.0/24>
>>> |
>>> Requirements:
>>>
>>> Connection should alway go via ROUTER GW, but default gateway for
>>> all machines in both networks should be pfsense (OPT1 and OPT2)
>>> If 172.24.24.12 is down conection should go via pfSense WAN
>>> interface
>>> If 192.168.212.20 is down conection should go via pfSense WAN
>>> interface
>>>
>>> Interface LAN not used because Failover gateway cannot be specified at
>>> pfSense 1.2.3 in LAN Interface
>>>
>>> I´m stucked. I followed MutiWAN tutorial, but when I create Failover
>>> using gateways to monitor, I see the same address for WAN an OPT1 in the
>>> pool...
>>>
>>> Any ideas
>>> Thanks
>>>
>>>
>>> --
>>> dpc
>>>
>>
>> I am afraid you have wrong understanding of MultiWAN.
>>
>> I think you should be doing the next:
>
>
> ( ) ( )
> ( inet ) ( inet )
> (____) (____)
> |22.22.22.4 |172.16.0.2
> | |
> | |
> |22.22.22.1(WAN) |172.16.0.1(OPT1)
> | ------------- |
> -----------|pfSense x2 |-------
> |___________|
> 172.24.24.20 (LAN) | |192.168.212.254(OPT2)
>
> | |
> | |
> 172.24.24.0/24 ------------ | 192.168.212.0/24
> -----------------
>
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [email protected]
> For additional commands, e-mail: [email protected]
>
> Commercial support available - https://portal.pfsense.org
>
>
--
dpc
