Hallo

ich mache gerade meine ersten Gehversuche mit ISDN.

Leider scheitert schon die Initialisierung beim booten. Ich habe schon 
verschiedene Interrupts probiert aber leider immer mit dem gleichen Er-
gebnis. 

Ich verwende eine "Teles 16.3c PnP". 

Leider weiss ich jetzt nicht mehr weiter.

Den Inhalt einiger Files habe ich im folgenden mal aufgelistet.


/var/log/messages
-----------------
Mar 17 06:46:15 athen kernel: klogd 1.3-3, log source = /proc/kmsg started.
Mar 17 06:46:15 athen kernel: Inspecting /boot/System.map
Mar 17 06:46:16 athen kernel: Loaded 5199 symbols from /boot/System.map.
Mar 17 06:46:16 athen kernel: Symbols match kernel version 2.0.36.
Mar 17 06:46:16 athen kernel: Loaded 5 symbols from 2 modules.
Mar 17 06:46:16 athen kernel: sysctl: ip forwarding off
Mar 17 06:46:16 athen kernel: ISDN subsystem Rev: 
1.44.2.9/1.41.2.11/1.48.2.27/1.28.2.2/1.8.2.2 loaded
Mar 17 06:46:16 athen kernel: HiSax: Linux Driver for passive ISDN cards
Mar 17 06:46:16 athen kernel: HiSax: Version 3.1 (module)
Mar 17 06:46:16 athen kernel: HiSax: Layer1 Revision 1.15.2.19
Mar 17 06:46:16 athen kernel: HiSax: Layer2 Revision 1.10.2.11
Mar 17 06:46:16 athen kernel: HiSax: TeiMgr Revision 1.8.2.7
Mar 17 06:46:16 athen kernel: HiSax: Layer3 Revision 1.10.2.6
Mar 17 06:46:16 athen kernel: HiSax: LinkLayer Revision 1.30.2.13
Mar 17 06:46:16 athen kernel: HiSax: Approval certification valid
Mar 17 06:46:16 athen kernel: HiSax: Approved with ELSA Quickstep series cards
Mar 17 06:46:16 athen kernel: HiSax: Approval registration numbers:
Mar 17 06:46:16 athen kernel: HiSax: German D133361J CETECOM ICT Services GmbH
Mar 17 06:46:16 athen kernel: HiSax: EU (D133362J) CETECOM ICT Services GmbH
Mar 17 06:46:16 athen kernel: HiSax: Total 1 card defined
Mar 17 06:46:16 athen kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
Mar 17 06:46:16 athen kernel: HiSax: Teles 16.3c driver Rev. 1.1.2.3
Mar 17 06:46:16 athen kernel: teles3c: defined at 0x100 IRQ 12 HZ 100
Mar 17 06:46:16 athen kernel: teles3c: resetting card
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ 12 count 0
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ 12 count 0
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ(12) getting no interrupts during init 1
Mar 17 06:46:16 athen kernel: teles3c: resetting card
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ 12 count 0
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ(12) getting no interrupts during init 2
Mar 17 06:46:16 athen kernel: teles3c: resetting card
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ 12 count 0
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ(12) getting no interrupts during init 3
Mar 17 06:46:16 athen kernel: HiSax: Card Teles 16.3c not installed !
Mar 17 06:46:16 athen kernel: ISDN-subsystem unloaded
Mar 17 06:46:16 athen kernel: ISDN subsystem Rev: 
1.44.2.9/1.41.2.11/1.48.2.27/1.28.2.2/1.8.2.2 loaded
Mar 17 06:46:16 athen kernel: HiSax: Linux Driver for passive ISDN cards
Mar 17 06:46:16 athen kernel: HiSax: Version 3.1 (module)
Mar 17 06:46:16 athen kernel: HiSax: Layer1 Revision 1.15.2.19
Mar 17 06:46:16 athen kernel: HiSax: Layer2 Revision 1.10.2.11
Mar 17 06:46:16 athen kernel: HiSax: TeiMgr Revision 1.8.2.7
Mar 17 06:46:16 athen kernel: HiSax: Layer3 Revision 1.10.2.6
Mar 17 06:46:16 athen kernel: HiSax: LinkLayer Revision 1.30.2.13
Mar 17 06:46:16 athen kernel: HiSax: Approval certification valid
Mar 17 06:46:16 athen kernel: HiSax: Approved with ELSA Quickstep series cards
Mar 17 06:46:16 athen kernel: HiSax: Approval registration numbers:
Mar 17 06:46:16 athen kernel: HiSax: German D133361J CETECOM ICT Services GmbH
Mar 17 06:46:16 athen kernel: HiSax: EU (D133362J) CETECOM ICT Services GmbH
Mar 17 06:46:16 athen kernel: HiSax: Warning - no protocol specified
Mar 17 06:46:16 athen kernel: HiSax: Note! module load syntax has changed.
Mar 17 06:46:16 athen kernel: HiSax: using protocol EURO
Mar 17 06:46:16 athen kernel: HiSax: Total 0 card defined
Mar 17 06:46:16 athen kernel: ISDN-subsystem unloaded
Mar 17 06:46:24 athen papd[147]: restart (1.4b2+asun2.0a18.2)
Mar 17 06:46:25 athen afpd[149]: main: atp_open: Invalid argument
Mar 17 06:46:25 athen afpd[149]: ASIP started on 192.168.0.99:548(1) 
(1.4b2+asun2.0a18.2) 
Mar 17 06:46:28 athen lpd[176]: restarted
Mar 17 06:46:32 athen /usr/sbin/cron[199]: (CRON) STARTUP (fork ok) 
Mar 17 06:46:32 athen squid[194]: Starting Squid Cache version 1.NOVM.21 for 
i686-pc-linux-gnu... 
Mar 17 06:46:33 athen su: (to postgres) root on /dev/console
Mar 17 06:46:34 athen squid[194]: Ready to serve requests. 
======================================================================

/var/log/warn
-------------
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ(12) getting no interrupts during init 1
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ(12) getting no interrupts during init 2
Mar 17 06:46:16 athen kernel: Teles 16.3c: IRQ(12) getting no interrupts during init 3
Mar 17 06:46:16 athen kernel: HiSax: Card Teles 16.3c not installed !
Mar 17 06:46:16 athen kernel: HiSax: Warning - no protocol specified
Mar 17 06:46:16 athen kernel: HiSax: Note! module load syntax has changed.
Mar 17 06:46:16 athen kernel: HiSax: using protocol EURO
Mar 17 06:46:25 athen afpd[149]: main: atp_open: Invalid argument
Mar 17 06:46:32 athen squid[194]: Starting Squid Cache version 1.NOVM.21 for 
i686-pc-linux-gnu... 
Mar 17 06:46:34 athen squid[194]: Ready to serve requests. 

======================================================================
/etc/isapnp
-----------
# $Id: pnpdump.c,v 1.17 1998/11/10 22:45:04 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR
#
# Trying port address 0203
# Board 1 has serial identifier 46 1b c8 07 bf 20 26 27 50

# (DEBUG)
(READPORT 0x0203)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING

# Card 1: (serial identifier 46 1b c8 07 bf 20 26 27 50)
# Vendor Id TAG2620, Serial Number 466094015, checksum 0x46.
# Version 1.0, Vendor version 2.1
# ANSI string -->TELES.S0/16.3c Plug&Play<--
#
# Logical device id TAG2620
#     Device support I/O range check register
#     Device supports vendor reserved register @ 0x38
#     Device supports vendor reserved register @ 0x3d
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE TAG2620/466094015 (LD 0
#     Logical device decodes 16 bit IO address lines
#         Minimum IO base address 0x0100
#         Maximum IO base address 0x0ffe
#         IO base alignment 2 bytes
#         Number of IO addresses required: 2
(IO 0 (SIZE 2) (BASE 0x0100))
#     IRQ 3, 5, 9, 10, 11, 12 or 15.
#         High true, edge sensitive interrupt (by default)
(INT 0 (IRQ 12 (MODE +E)))
#     Vendor defined tag:  84 a1 32 36 32 30 39 30 31 38 33 30 37 31 31 32
#     Vendor defined tag:  84 a2 54 45 4c 45 53
 (NAME "TAG2620/466094015[0]{TELES.S0/16.3c Plug&Play}")
(ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)

======================================================================
isapnp /etc/isapnp.conf
-----------------------
lspci not found, so PCI resource conflict not checked
Board 1 has Identity 27 10 0a 8d e9 2b 00 8c 0e:  CTL002b Serial No 269127145 
[checksum 27]
Board 2 has Identity 46 1b c8 07 bf 20 26 27 50:  TAG2620 Serial No 466094015 
[checksum 46]
TAG2620/466094015[0]{TELES.S0/16.3c Plug&Play}: Port 0x100; IRQ12 --- Enabled OK

======================================================================
/etc/rc.config.d/i4l_hisax.rc.config
------------------------------------
#
# driver-id for HiSax-driver
#   set to "HiSax"
#   or whatever you defined when loading driver within kernel
#   set to "" if you don't have a hisax-card
#
I4L_ID="HiSax"
# Type   ISDN-card                Required parameters
# ----   ---------------------    -------------------------------------------
#    1   Teles 16.0               irq, mem, io
#    2   Teles  8.0               irq, mem
#    3   Teles 16.3 (non PnP)     irq, io
#    4   Creatix/Teles PnP        irq, io0 (ISAC), io1 (HSCX)
#    5   AVM A1 (Fritz)           irq, io
#    6   ELSA PCC/PCF cards       io or nothing for autodetect (the iobase is
#                                 only required, if you have more than one ELSA
#                                 card in your PC)
#    7   ELSA Quickstep 1000      irq, io  (from isapnp setup)
#    8   Teles 16.3 PCMCIA        irq, io
#    9   ITK ix1-micro Rev.2      irq, io
# since: HiSax 2.5:
#   10   ELSA PCMCIA              irq, io  (set with card manager)
#   11   Eicon.Diehl Diva ISA PnP irq, io
#   11   Eicon.Diehl Diva PCI     no parameter
#   12   ASUS COM ISDNLink        irq, io  (from isapnp setup)
#   13   HFC-2BS0 based cards     irq, io  
#   14   Teles 16.3c              irg, io
#   15   Sedlbauer Speed Card     irq, io  
#        (= Teledat 100)
#   16   USR Sportster internal   irq, io  
#   17   MIC card                 irq, io  
#   18   ELSA Quickstep 1000PCI   no parameter
#   19   Compaq ISDN S0 ISA card  irq, io0, io1, io (from isapnp setup io=IO2)
#   20   NETjet PCI card          no parameter
#   21   Teles PCI                no parameter
#   22   Sedlbauer Speed Star (PCMCIA) irq, io (set with card manager)
#   24   Dr. Neuhaus Niccy PnP    irq, io0, io1 (from isapnp setup)
#   24   Dr. Neuhaus Niccy PCI    no parameter
#   25   Teles S0Box              irq, io (of the used lpt port)
#
I4L_TYPE="14"
#
# IRQ of Teles Card
#   eg. 12 or 15 when loading as module
#   set to "" when driver is loaded within kernel
#
I4L_IRQ="12"
#
# Membase of Teles card (e.g. "0xd2000" for Teles S0/16, "0" for Teles S0/16.3)
#
I4L_MEMBASE="0"
#
# Portaddress of Teles card (e.g. 0xd80, "0" for S0/8)
#
I4L_PORT="0x0100"
#
# for Creatix PNP: IO0 (ISAC)
#
# I4L_IO0=""
#
# for Creatix PNP: IO1 (HSCX)
#
# I4L_IO1=""
#
# for HiSax-modul: the complete line to load module
#   e.g Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and ELSA PCF, Euro ISDN:
#      "type=5,6 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa"
#
I4L_MODUL_OPTIONS=""
======================================================================



---------------------------------------------------------------------

**   Marcus Thiedecke                   E-mail:  [EMAIL PROTECTED]



-
To unsubscribe from this list please send a mail to [EMAIL PROTECTED] with
'unsubscribe suse-isdn' in its body.

Antwort per Email an