How is your parallel port setup in the bios ? did you install the paprallel
port support ? did you compile the ppa module with the slow epp16 support ?
cheers
Michael
On 24-Feb-99 W.D.McKinney wrote:
>
> I tried compiling support for ZIP+ external drive into my kernel 2.2.2
> with the following on bootup ?
>
> <4>imm: Version 2.03 (for Linux 2.0.0)
> <4>imm: parport reports no devices.
>
> It was connected with a disk in it.
>
> I have a SCSI system with the following :
>
> <4>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.10/3.2.4
> <4> <Adaptec AHA-294X Ultra SCSI host adapter>
> <4>scsi : 1 host.
> <4> Vendor: SEAGATE Model: ST15150W Rev: 0023
> <4> Type: Direct-Access ANSI SCSI revision: 02
> <4>Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> <4> Vendor: SEAGATE Model: ST15150N Rev: 0023
> <4> Type: Direct-Access ANSI SCSI revision: 02
> <4>Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
> <4> Vendor: SEAGATE Model: ST15230W SUN4.2G Rev: 0738
> <4> Type: Direct-Access ANSI SCSI revision: 02
> <4>Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
> <4> Vendor: PLEXTOR Model: CD-ROM PX-20TS Rev: 1.01
> <4> Type: CD-ROM ANSI SCSI revision: 02
> <4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 3, lun 0
> <4> Vendor: HP Model: T4000s Rev: 1.10
> <4> Type: Sequential-Access ANSI SCSI revision: 02
> <4>Detected scsi tape st0 at scsi0, channel 0, id 4, lun 0
> <4> Vendor: YAMAHA Model: CDR400t Rev: 1.0d
> <4> Type: CD-ROM ANSI SCSI revision: 02
> <4>Detected scsi CD-ROM sr1 at scsi0, channel 0, id 6, lun 0
> <4>scsi : detected 1 SCSI tape 2 SCSI cdroms 3 SCSI disks total.
> <6>(scsi0:0:3:0) Synchronous at 10.0 Mbyte/sec, offset 15.
> <6>Uniform CDROM driver Revision: 2.52
> <4>sr1: scsi3-mmc drive: 6x/6x writer xa/form2 cdda tray
> <6>(scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 8.
> <4>SCSI device sda: hdwr sector= 512 bytes. Sectors= 8388315 [4095 MB] [4.1
> GB]
> <6>(scsi0:0:1:0) Synchronous at 10.0 Mbyte/sec, offset 15.
> <4>SCSI device sdb: hdwr sector= 512 bytes. Sectors= 8388315 [4095 MB] [4.1
> GB]
> <6>(scsi0:0:2:0) Synchronous at 20.0 Mbyte/sec, offset 8.
> <4>SCSI device sdc: hdwr sector= 512 bytes. Sectors= 8386733 [4095 MB] [4.1
> GB]
>
>
> What else should be configured for the ZIP+ to work ?
> Thanks so much.
>
> -Dee
>
>
> W.D.McKinney (Dee) [EMAIL PROTECTED]
> Faith is acting on your passions & beliefs.
>
> -
> To get out of this list, please send email to [EMAIL PROTECTED] with
> this text in its body: unsubscribe suse-linux-e
> Check out the SuSE-FAQ at http://www.suse.com/Support/Doku/FAQ/ and the
> archive at http://www.suse.com/Mailinglists/suse-linux-e/index.html
----------------------------------
E-Mail: [EMAIL PROTECTED]
Date: 24-Feb-99
Time: 11:33:15
This message was sent by XFMail
----------------------------------
-
To get out of this list, please send email to [EMAIL PROTECTED] with
this text in its body: unsubscribe suse-linux-e
Check out the SuSE-FAQ at http://www.suse.com/Support/Doku/FAQ/ and the
archive at http://www.suse.com/Mailinglists/suse-linux-e/index.html
