Hi,
beim Senden von Faxen bricht Hylafax die Übertragung ab und liefert
untenstehende Mail zurück. Beim Empfänger kommt das Fax zwar an,
bricht aber am Schluss mit Fehlermeldung ab.
Als Faxclient kommt WHFC zum Einsatz. Diese Fehlermeldung tritt
erst seit ein paar Tagen auf, vorher lief alles Einwandfrei. Das
Modem ist ein Noname und unterstützt CLASS1 und CLASS2.
Hat jemand ne Idee an was das liegen könnte.
++++++ schnipp ++++++
Your facsimile job to xxxxxx failed because:
No response to MPS or EOP repeated 3 tries; too many attempts to
dial
---- Transcript of session follows ----
Mar 11 10:40:03.52: [ 1477]: SESSION BEGIN 00000089 xxxxxx
Mar 11 10:40:03.52: [ 1477]: SEND FAX: JOB 67 DEST xxxxxx COMMID
00000089 Mar 11 10:40:03.52: [ 1477]: MODEM set DTR OFF
Mar 11 10:40:03.52: [ 1477]: DELAY 2600 ms
Mar 11 10:40:06.13: [ 1477]: MODEM set DTR ON
Mar 11 10:40:06.13: [ 1477]: MODEM set baud rate: 19200 baud, input
flow NONE, output flow NONE Mar 11 10:40:06.13: [ 1477]: MODEM flush
i/o Mar 11 10:40:06.13: [ 1477]: <-- [15:ATE0V1Q0S0=0H0\r]
Mar 11 10:40:06.15: [ 1477]: --> [2:OK]
Mar 11 10:40:06.15: [ 1477]: <-- [12:ATS8=2S7=60\r]
Mar 11 10:40:06.17: [ 1477]: --> [2:OK]
Mar 11 10:40:06.17: [ 1477]: <-- [12:AT+FCLASS=1\r]
Mar 11 10:40:06.19: [ 1477]: --> [2:OK]
Mar 11 10:40:06.19: [ 1477]: <-- [5:ATM0\r]
Mar 11 10:40:06.20: [ 1477]: --> [2:OK]
Mar 11 10:40:06.20: [ 1477]: MODEM input buffering enabled
Mar 11 10:40:06.20: [ 1477]: <-- [12:AT+FCLASS=1\r]
Mar 11 10:40:06.32: [ 1477]: --> [2:OK]
Mar 11 10:40:06.32: [ 1477]: DIAL 38279
Mar 11 10:40:06.32: [ 1477]: <-- [10:ATDTxxxxxx\r]
Mar 11 10:40:17.07: [ 1477]: --> [7:CONNECT]
Mar 11 10:40:17.07: [ 1477]: MODEM input buffering disabled
Mar 11 10:40:18.18: [ 1477]: --> [2:OK]
Mar 11 10:40:18.18: [ 1477]: <-- [9:AT+FRH=3\r]
Mar 11 10:40:18.20: [ 1477]: --> [7:CONNECT]
Mar 11 10:40:18.90: [ 1477]: --> [2:OK]
Mar 11 10:40:18.90: [ 1477]: REMOTE CSI "+49 7821 xxxxxx"
Mar 11 10:40:18.90: [ 1477]: <-- [9:AT+FRH=3\r]
Mar 11 10:40:18.92: [ 1477]: --> [7:CONNECT]
Mar 11 10:40:19.28: [ 1477]: --> [2:OK]
Mar 11 10:40:19.28: [ 1477]: REMOTE best rate 9600 bit/s
Mar 11 10:40:19.28: [ 1477]: REMOTE max page width 1728 pixels in 215 mm
Mar 11 10:40:19.28: [ 1477]: REMOTE max unlimited page length
Mar 11 10:40:19.28: [ 1477]: REMOTE best vres 7.7 line/mm
Mar 11 10:40:19.28: [ 1477]: REMOTE best format 1-D MR
Mar 11 10:40:19.28: [ 1477]: REMOTE supports T.30 Annex A, ECM
Mar 11 10:40:19.28: [ 1477]: REMOTE best 20 ms, 10 ms/scanline
Mar 11 10:40:19.28: [ 1477]: USE 9600 bit/s
Mar 11 10:40:19.28: [ 1477]: USE 20 ms, 10 ms/scanline
Mar 11 10:40:19.28: [ 1477]: SEND file "docq/doc68.ps;00"
Mar 11 10:40:19.28: [ 1477]: USE page width 1728 pixels in 215 mm
Mar 11 10:40:19.28: [ 1477]: USE unlimited page length
Mar 11 10:40:19.28: [ 1477]: USE 3.85 line/mm
Mar 11 10:40:19.28: [ 1477]: USE 1-D MR
Mar 11 10:40:19.28: [ 1477]: SEND training at v.29 9600 bit/s
Mar 11 10:40:19.28: [ 1477]: <-- [9:AT+FTH=3\r]
Mar 11 10:40:19.33: [ 1477]: --> [7:CONNECT]
Mar 11 10:40:21.12: [ 1477]: --> [7:CONNECT]
Mar 11 10:40:21.56: [ 1477]: --> [2:OK]
Mar 11 10:40:21.56: [ 1477]: DELAY 75 ms
Mar 11 10:40:21.65: [ 1477]: <-- [10:AT+FTM=96\r]
Mar 11 10:40:21.71: [ 1477]: --> [7:CONNECT]
Mar 11 10:40:23.67: [ 1477]: --> [2:OK]
Mar 11 10:40:23.67: [ 1477]: <-- [9:AT+FRH=3\r]
Mar 11 10:40:24.60: [ 1477]: --> [7:CONNECT]
Mar 11 10:40:25.57: [ 1477]: --> [2:OK]
Mar 11 10:40:25.57: [ 1477]: TRAINING succeeded
Mar 11 10:40:25.57: [ 1477]: <-- [10:AT+FTM=96\r]
Mar 11 10:40:25.64: [ 1477]: --> [7:CONNECT]
Mar 11 10:40:25.64: [ 1477]: SEND begin page
Mar 11 10:40:39.61: [ 1477]: SENT 27464 bytes of data
Mar 11 10:40:45.60: [ 1477]: SENT 11397 bytes of data
Mar 11 10:40:45.60: [ 1477]: SEND 1D RTC
Mar 11 10:40:45.60: [ 1477]: SEND end page
Mar 11 10:40:56.23: [ 1477]: --> [2:]
Mar 11 10:40:56.23: [ 1477]: --> [2:OK]
Mar 11 10:40:56.23: [ 1477]: DELAY 95 ms
Mar 11 10:40:56.34: [ 1477]: SEND send EOP (no more pages or documents)
Mar 11 10:40:56.34: [ 1477]: <-- [9:AT+FTH=3\r]
Mar 11 10:40:56.39: [ 1477]: --> [7:CONNECT]
Mar 11 10:40:57.70: [ 1477]: --> [2:OK]
Mar 11 10:40:57.70: [ 1477]: <-- [9:AT+FRH=3\r]
Mar 11 10:41:00.80: [ 1477]: --> [0:]
Mar 11 10:41:00.80: [ 1477]: MODEM <Empty line>
Mar 11 10:41:00.80: [ 1477]: MODEM TIMEOUT: waiting for v.21 carrier
Mar 11 10:41:00.86: [ 1477]: --> [2:OK]
Mar 11 10:41:00.86: [ 1477]: SEND send EOP (no more pages or documents)
Mar 11 10:41:00.86: [ 1477]: <-- [9:AT+FTH=3\r]
Mar 11 10:41:00.91: [ 1477]: --> [7:CONNECT]
Mar 11 10:41:02.23: [ 1477]: --> [2:OK]
Mar 11 10:41:02.23: [ 1477]: <-- [9:AT+FRH=3\r]
Mar 11 10:41:05.33: [ 1477]: --> [0:]
Mar 11 10:41:05.33: [ 1477]: MODEM <Empty line>
Mar 11 10:41:05.33: [ 1477]: MODEM TIMEOUT: waiting for v.21 carrier
Mar 11 10:41:05.39: [ 1477]: --> [2:OK]
Mar 11 10:41:05.39: [ 1477]: SEND send EOP (no more pages or documents)
Mar 11 10:41:05.39: [ 1477]: <-- [9:AT+FTH=3\r]
Mar 11 10:41:05.44: [ 1477]: --> [7:CONNECT]
Mar 11 10:41:06.76: [ 1477]: --> [2:OK]
Mar 11 10:41:06.76: [ 1477]: <-- [9:AT+FRH=3\r]
Mar 11 10:41:09.86: [ 1477]: --> [0:]
Mar 11 10:41:09.86: [ 1477]: MODEM <Empty line>
Mar 11 10:41:09.86: [ 1477]: MODEM TIMEOUT: waiting for v.21 carrier
Mar 11 10:41:09.92: [ 1477]: --> [2:OK]
Mar 11 10:41:09.92: [ 1477]: <-- [9:AT+FTH=3\r]
Mar 11 10:41:09.97: [ 1477]: --> [7:CONNECT]
Mar 11 10:41:11.29: [ 1477]: --> [2:OK]
Mar 11 10:41:11.29: [ 1477]: MODEM input buffering enabled
Mar 11 10:41:11.29: [ 1477]: SEND FAILED: No response to MPS or EOP
repeated 3 tries; too many attempts to dial
Mar 11 10:41:11.29: [ 1477]: <-- [5:ATH0\r]
Mar 11 10:41:12.01: [ 1477]: --> [2:OK]
Mar 11 10:41:12.01: [ 1477]: MODEM set DTR OFF
Mar 11 10:41:12.01: [ 1477]: SESSION END
++++++ schnipp ende ++++++
gruss Karsten
--
--------------------------------------------
Karsten Sommer <[EMAIL PROTECTED]>
" WYTYSYDG - What you thought you saw, you didn't get "
--
Um aus der Liste ausgetragen zu werden, eine Mail an [EMAIL PROTECTED]
schicken, mit dem Text: unsubscribe suse-linux
