Hi, i have compiled a 64Bit 2.4.19 kernel for my Blade100. i can boot this kernel without problems but my (usb) keyboard and mouse does not work although they were found by the new kernel (see below). with the standard kernel everything works fine.
i have used "make oldconfig" with the vmlinuz.config from /boot to configure the kernel and gave default answers to all remaining questions. does anyone know whats the crux of the matter ? regards, Paul here's a dump of my boot.omsg: Cannot find map file. Loaded 11 symbols from 2 modules. klogd 1.4.1, log source = ksyslog started. <4>PROMLIB: Sun IEEE Boot Prom 4.0.45 2001/02/08 14:33 <4>Linux version 2.4.19 (root@turing) (gcc version egcs-2.92.11 19980921 (gcc2 ss-980609 experimental)) #2 Mit Aug 14 01:29:47 CEST 2002 <4>ARCH: SUN4U <4>Ethernet address: 00:03:ba:0e:5f:f7 <4>On node 0 totalpages: 48423 <4>zone(0): 147345 pages. <4>zone(1): 0 pages. <4>zone(2): 0 pages. <4>Found CPU 0 (node=f006dbd4,mid=0) <4>Found 1 CPU prom device tree node(s). <4>Kernel command line: root=/dev/hda4 ro ide=nodma <4>ide_setup: ide=nodmaIDE: Prevented DMA <4>Console: colour dummy device 80x25 <4>Calibrating delay loop... 1002.70 BogoMIPS <4>Memory: 373488k available (1912k kernel code, 360k data, 160k init) [fffff80000000000,0000000047f22000] <6>Dentry cache hash table entries: 65536 (order: 7, 1048576 bytes) <6>Inode cache hash table entries: 32768 (order: 6, 524288 bytes) <4>Mount-cache hash table entries: 8192 (order: 4, 131072 bytes) <4>Buffer-cache hash table entries: 16384 (order: 4, 131072 bytes) <4>Page-cache hash table entries: 65536 (order: 6, 524288 bytes) <4>POSIX conformance testing by UNIFIX <4>PCI: Probing for controllers. <4>PCI: Found SABRE, main regs at 000001fe00000000, wsync at 000001fe00001c20 <4>SABRE: Shared PCI config space at 000001fe01000000 <4>SABRE: DVMA at c0000000 [20000000] <4>PCI-IRQ: Routing bus[ 0] slot[ 8] map[0] to INO[23] <4>PCI-IRQ: Routing bus[ 0] slot[ c] map[0] to INO[06] <4>PCI-IRQ: Routing bus[ 0] slot[ c] map[0] to INO[1c] <4>PCI-IRQ: Routing bus[ 0] slot[ c] map[0] to INO[24] <4>PCI-IRQ: Routing bus[ 0] slot[ d] map[0] to INO[0c] <4>PCI-IRQ: Routing bus[ 0] slot[13] map[0] to INO[0f] <4>PCI0(PBMA): Bus running at 33MHz <4>isa0: [dma -> (floppy) (parallel)] [power] [serial] [serial] <4>ebus0: [flashprom] [eeprom] [idprom] <6>PCIO serial driver version 1.54 <6>su(serial) at 0x1fe020003f8 (tty 0 irq 12,7eb) is a 16550A <6>su(serial) at 0x1fe020002e8 (tty 1 irq 12,7eb) is a 16550A <6>Linux NET4.0 for Linux 2.4 <6>Based upon Swansea University Computer Society NET3.039 <4>Initializing RT netlink socket <4>Starting kswapd <5>VFS: Diskquotas version dquot_6.4.0 initialized <4>atyfb: 3D RAGE (XL) [0x4752 rev 0x27] 8M SDRAM, 29.498928 MHz XTAL, 230 MHz PLL, 100 Mhz MCLK <4>Console: switching to colour frame buffer device 144x56 <4>fb0: ATY Mach64 frame buffer device on PCI <4>kbd_init: Assuming USB keyboard. <4>isa(speaker): iobase[000001fe02000042:000001fe02000061] <4>pty: 256 Unix98 ptys configured <3>rtc_init: no PC rtc found <6>Uniform Multi-Platform E-IDE driver Revision: 6.31 <4>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <4>ALI15X3: IDE controller on PCI bus 00 dev 68 <4>ALI15X3: chipset revision 195 <4>ALI15X3: 100%% native mode on irq 4,7cc <4> ide0: BM-DMA at 0x1fe02000a20-0x1fe02000a27, BIOS settings: hda:pio, hdb:pio <4> ide1: BM-DMA at 0x1fe02000a28-0x1fe02000a2f, BIOS settings: hdc:pio, hdd:pio <4>hda: ST320414A, ATA DISK drive <4>hdb: LTN486S, ATAPI CD/DVD-ROM drive <4>ide0 at 0x1fe02000a00-0x1fe02000a07,0x1fe02000a1a on irq 4,7cc <6>hda: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=39535/16/63 <4>hdb: ATAPI 48X CD-ROM drive, 120kB Cache <6>Uniform CD-ROM driver Revision: 3.12 <6>Partition check: <6> hda: hda1 hda2 hda3 hda4 <4>RAMDISK driver initialized: 16 RAM disks of 128000K size 1024 blocksize <6>loop: loaded (max 8 devices) <6>SCSI subsystem driver Revision: 1.00 <3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 <3>kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2 <6>usb.c: registered new driver usbdevfs <6>usb.c: registered new driver hub <6>usb-ohci.c: USB OHCI at membase 0x1ff02000000, IRQ 9,7e4 <6>usb-ohci.c: usb-00:0c.3, PCI device 108e:1103 <6>usb.c: new USB bus registered, assigned bus number 1 <6>hub.c: USB hub found <6>hub.c: 4 ports detected <6>usb.c: registered new driver hid <6>hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]> <6>hid-core.c: USB HID support drivers <6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <6>NET4: Linux TCP/IP 1.0 for NET4.0 <6>IP Protocols: ICMP, UDP, TCP, IGMP <6>IP: routing cache hash table of 4096 buckets, 64Kbytes <6>TCP: Hash tables configured (established 32768 bind 32768) <6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. <5>RAMDISK: Compressed image found at block 0 <4>Freeing initrd memory: 612k freed <4>VFS: Mounted root (ext2 filesystem). <6>mice: PS/2 mouse device common for all mice <6>hub.c: USB new device connect on bus1/2, assigned device number 2 <6>hiddev0: USB HID v0.01 Mouse [Logitech] on usb1:2.0 <6>hub.c: USB new device connect on bus1/4, assigned device number 3 <6>hiddev0: USB HID v0.01 Keyboard [046a:0001] on usb1:3.0 <4>reiserfs: checking transaction log (device 03:04) ... <4>Using r5 hash to sort names <4>ReiserFS version 3.6.25 <4>VFS: Mounted root (reiserfs filesystem) readonly. <5>Trying to move old root to /initrd ... failed <5>Unmounting old root <5>Trying to free ramdisk memory ... okay <4>sys32_ioctl(showconsole:30): Unknown cmd fd(0) cmd(40045432) arg(effffc04) <6>Adding Swap: 491888k swap-space (priority 42) <4>hda: DMA disabled <4>hdb: DMA disabled <4>hdb: CHECK for good STATUS Kernel logging (ksyslog) stopped. Kernel log daemon terminating. -- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
