Dear Listmembers,
I recently added an external Raid Array from Promise to my U 60 that
basically works. However, it always says "Target did not report SYNC" at
boot - what means to have a really slow 5MB/sec asynchronious
interconnection. The Promise device is a quite up to date SX4000 device. I
used to fiddle around a bit with external termination - in vain. It works
but it is slow.
Does anybody out there have a clue what could be the cause of this?
Many thanks for your efforts in advance,
take care



Dieter Jurzitza

Parts of the boot-log:
 <6>sym53c8xx: at PCI bus 0, device 3, function 0
 <6>sym53c8xx: 53c875 detected 
 <6>sym53c875-0: rev 0x26 on pci bus 0 device 3 function 0 irq 3,7e0
 <6>sym53c875-0: ID 7, Fast-20, Parity Checking
 <6>scsi0 : sym53c8xx-1.7.3c-20010512
 <4>  Vendor: Promise   Model: 4 Disk RAID5      Rev: 1.10
 <4>  Type:   Direct-Access                      ANSI SCSI revision: 03
 <4>  Vendor: IBM       Model: DDRS-39130D       Rev: DC1B
 <4>  Type:   Direct-Access                      ANSI SCSI revision: 02
 <4>  Vendor: YAMAHA    Model: CRW4416S          Rev: 1.0e
 <4>  Type:   CD-ROM                             ANSI SCSI revision: 02
 <4>  Vendor: PIONEER   Model: CD-ROM DR-U16S    Rev: 1.01
 <4>  Type:   CD-ROM                             ANSI SCSI revision: 02
 <4>Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
 <4>Attached scsi disk sdb at scsi0, channel 0, id 3, lun 0
 <4>Attached scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
 <4>Attached scsi CD-ROM sr1 at scsi0, channel 0, id 6, lun 0
 <6>sym53c875-0-<5,*>: FAST-10 SCSI 8.0 MB/s (125.0 ns, offset 16)
 <4>sr0: scsi3-mmc drive: 16x/16x writer cd/rw xa/form2 cdda tray
 <6>Uniform CD-ROM driver Revision: 3.12
 <6>sym53c875-0-<6,*>: FAST-20 SCSI 20.0 MB/s (50.0 ns, offset 16)
 <4>sr1: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
 <6>sym53c875-0-<0,*>: target did not report SYNC.
 <6>sym53c875-0-<0,*>: target did not report SYNC.
 <4>SCSI device sda: 597656064 512-byte hdwr sectors (306000 MB)
 <6>Partition check:
 <6> sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7


-- 
________________________________________________

HARMAN BECKER AUTOMOTIVE SYSTEMS

Dr.-Ing. Dieter Jurzitza
Manager Hardware Systems
         ESI

Industriegebiet Ittersbach
Becker-G�ring Str. 16
D-76307 Karlsbad / Germany

Phone: +49 (0)7248 71-1577
Fax:   +49 (0)7248 71-1216
eMail: [EMAIL PROTECTED]
Internet: http://www.becker.de
 

--
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]

Reply via email to