El Lunes, 12 de Febrero de 2007, Rafael J. Wysocki escribió:
> Which kernel do you use?
>
> Rafael
Rafael,
# uname -r
2.6.18.2-34
I also attach a dmesg.txt of my boot procces.
Thank you in advance.
--
Xavier Callejas
International Bonded Couriers
El Salvador
+503 2250-5900
¡Toda una Organización Mundial a Su Servicio!
------------------------------------------------------
Open Your Mind, Use Open Source.
Linux version 2.6.18.2-34-xavier ([EMAIL PROTECTED]) (gcc version 4.1.2
20061115 (prerelease) (SUSE Linux)) #1 SMP Wed Dec 13 15:12:02 CST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bf70000 (usable)
BIOS-e820: 000000001bf70000 - 000000001bf7b000 (ACPI data)
BIOS-e820: 000000001bf7b000 - 000000001bf80000 (ACPI NVS)
BIOS-e820: 000000001bf80000 - 000000001c000000 (reserved)
BIOS-e820: 000000002bf80000 - 000000002c000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
447MB LOWMEM available.
found SMP MP-table at 000f6ae0
On node 0 totalpages: 114544
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 110448 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6b40
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1bf75dd2
ACPI: FADT (v001 TOSCPL Chinook 0x06040000 ATI 0x00000003) @ 0x1bf7af24
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x1bf7af98
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @ 0x1bf75e02
ACPI: DSDT (v001 TOSCPL SB200 0x06040000 MSFT 0x0100000e) @ 0x00000000
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: Skipping IOAPIC probe due to 'noapic' option.
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: Product ID: RS300 Board APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Allocating PCI resources starting at 30000000 (gap: 2c000000:d2c00000)
Detected 3066.623 MHz processor.
Built 1 zonelists. Total pages: 114544
Kernel command line: root=/dev/hda3 vga=0x317 resume=/dev/hda2 acpi_irq_balance
noapic lapic elevator=
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 447208k/458176k available (1687k kernel code, 10436k reserved, 922k
data, 192k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 6139.00 BogoMIPS (lpj=3069502)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000459d
00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000459d
00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000180 0000459d
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
checking if image is initramfs... it is
Freeing initrd memory: 3154k freed
ACPI: Core revision 20060707
ACPI: successfully read 16816 bytes from file /DSDT.aml
ACPI: Override [DSDT- SB200] from initramfs - tainting kernel
ACPI (tbget-0297): Table [DSDT] replaced by host OS [20060707]
ACPI: setting ELCR to 0200 (from 0800)
CPU0: Intel Mobile Intel(R) Pentium(R) 4 CPU 3.06GHz stepping 01
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6132.73 BogoMIPS (lpj=3066368)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000459d
00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000459d
00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000180 0000459d
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel Mobile Intel(R) Pentium(R) 4 CPU 3.06GHz stepping 01
Total of 2 processors activated (12271.74 BogoMIPS).
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=30
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd958, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNK0] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNK1] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNK2] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNK3] (IRQs 10 *11)
ACPI: Embedded Controller [EC0] (gpe 6) interrupt mode.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:07: ioport range 0x1080-0x1080 has been reserved
pnp: 00:07: ioport range 0x220-0x22f has been reserved
pnp: 00:07: ioport range 0x40b-0x40b has been reserved
pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: e8100000-e81fffff
PREFETCH window: f0000000-f7ffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 0000a400-0000a4ff
IO window: 0000a800-0000a8ff
PREFETCH window: 30000000-31ffffff
MEM window: 32000000-33ffffff
PCI: Bridge: 0000:00:14.4
IO window: a000-afff
MEM window: e8200000-e82fffff
PREFETCH window: 30000000-31ffffff
ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNK0] -> GSI 11 (level, low) ->
IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Machine check exception polling timer started.
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1171295240.171:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
vesafb: framebuffer at 0xf0000000, mapped to 0xdc880000, using 6144k, total
65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:52d0
vesafb: pmi: set display start = c00c533e, set palette = c00c5378
vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 81749
bytes,<6>...found (1024x768, 46202 bytes, v3).
Console: switching to colour frame buffer device 124x44
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
ACPI Error (evregion-0317): No handler for Region [ECR_] (dbf5bbb4)
[EmbeddedControl] [20060707]
ACPI Error (exfldio-0290): Region EmbeddedControl(3) has no handler [20060707]
ACPI Exception (dswexec-0458): AE_NOT_EXIST, While resolving operands for
[OpcodeName unavailable] [20060707]
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.EPWR.PCLK]
(Node dbf5cc48), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed
[\_SB_.PCI0.LPC0.EC0_._Q1E] (Node dbf538ec), AE_NOT_EXIST
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:14.6[B] -> Link [LNK1] -> GSI 10 (level, low) ->
IRQ 10
ACPI: PCI interrupt for device 0000:00:14.6 disabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 1
Starting balanced_irq
Using IPI No-Shortcut mode
Time: tsc clocksource has been installed.
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 192k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> Link [LNK0] -> GSI 11 (level, low) ->
IRQ 11
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8070-0x8077, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8078-0x807f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
input: PS/2 Mouse as /class/input/input2
input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
hda: IC25N060ATMR04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 512KiB
hda: 117210240 sectors (60011 MB) w/7884KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 >
Probing IDE interface ide1...
input: PS/2 Mouse as /class/input/input4
input: AlpsPS/2 ALPS GlidePoint as /class/input/input5
hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4243N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist]
[20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst]
[20060707]
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist]
[20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Cst]
[20060707]
ACPI: Processor [CPU1] (supports 8 throttling states)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
PCI: Enabling device 0000:00:14.6 (0010 -> 0012)
ACPI: PCI Interrupt 0000:00:14.6[B] -> Link [LNK1] -> GSI 10 (level, low) ->
IRQ 10
ALSA sound/pci/atiixp_modem.c:503: atiixp-modem: codec reset timeout
ACPI: PCI Interrupt 0000:00:14.5[B] -> Link [LNK1] -> GSI 10 (level, low) ->
IRQ 10
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Linux agpgart interface v0.101 (c) Dave Jones
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNK3] -> GSI 11 (level, low) ->
IRQ 11
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 11, io mem 0xe8001000
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18.2-34-xavier ohci_hcd
usb usb1: SerialNumber: 0000:00:13.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNK3] -> GSI 11 (level, low) ->
IRQ 11
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 11, io mem 0xe8002000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18.2-34-xavier ohci_hcd
usb usb2: SerialNumber: 0000:00:13.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
ACPI: PCI Interrupt 0000:00:13.2[A] -> Link [LNK3] -> GSI 11 (level, low) ->
IRQ 11
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usb 1-1: new low speed USB device using ohci_hcd and address 2
ehci_hcd 0000:00:13.2: irq 11, io mem 0xe8003000
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.18.2-34-xavier ehci_hcd
usb usb3: SerialNumber: 0000:00:13.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
wlan: 0.8.4.2 (svn r1850)
ath_rate_sample: 1.2 (svn r1850)
ath_pci: 0.9.4.5 (svn r1850)
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Yenta: CardBus bridge found at 0000:02:04.0 [1179:ff00]
Yenta: Using CSCINT to route CSC interrupts to PCI
agpgart: Detected Ati IGP9100/M chipset
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x00111c12, devctl 0x44
agpgart: AGP aperture is 32M @ 0xea000000
8139too Fast Ethernet driver 0.9.27
Yenta: ISA IRQ mask 0x0068, PCI irq 11
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xe8200000 - 0xe82fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNK2] -> GSI 10 (level, low) ->
IRQ 10
usb 1-1: new low speed USB device using ohci_hcd and address 3
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps
36Mbps 48Mbps 54Mbps
wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
usb 1-1: new device found, idVendor=09da, idProduct=0006
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB Optical Mouse
usb 1-1: Manufacturer: A4Tech
usb 1-1: configuration #1 chosen from 1 choice
wifi0: mac 5.9 phy 4.3 radio 4.6
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
usbcore: registered new driver hiddev
wifi0: Atheros 5212: mem=0xe8200000, irq=10
ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNK3] -> GSI 11 (level, low) ->
IRQ 11
eth0: RealTek RTL8139 at 0xdd0c6000, 00:0f:b0:54:f3:17, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
input: A4Tech USB Optical Mouse as /class/input/input6
input: USB HID v1.10 Mouse [A4Tech USB Optical Mouse] on usb-0000:00:13.0-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57
0xc68-0xc6f 0xcd0-0xcd7
cs: IO port probe 0xa00-0xaff: clean.
Adding 722916k swap on /dev/hda2. Priority:-1 extents:1 across:722916k
Adding 208804k swap on /dev/hda9. Priority:-2 extents:1 across:208804k
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [EMAIL PROTECTED]
loop: loaded (max 8 devices)
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs warning (device hda1): load_system_files(): Unsupported volume flags
0x4000 encountered.
NTFS-fs warning (device hda1): load_system_files(): Volume has unsupported
flags set. Will not be able to remount read-write. Run chkdsk and mount in
Windows.
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
reiserfs: using flush barriers
ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
ReiserFS: hda7: found reiserfs format "3.6" with standard journal
ReiserFS: hda7: using ordered data mode
reiserfs: using flush barriers
ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18,
max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda7: checking transaction log (hda7)
ReiserFS: hda7: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
AppArmor: AppArmor initialized
audit(1171295271.511:2): AppArmor initialized
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
powernow: This module only works with AMD K7 CPUs
acpi-cpufreq: CPU0 - ACPI performance management activated.
acpi-cpufreq: CPU1 - ACPI performance management activated.
audit(1171316890.304:3): audit_pid=2970 old=0 by auid=4294967295
IA-32 Microcode Update Driver: v1.14a <[EMAIL PROTECTED]>
microcode: CPU1 updated from revision 0x9 to 0x17, date = 04222005
microcode: CPU0 updated from revision 0x9 to 0x17, date = 04222005
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
NET: Registered protocol family 17
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNK0] -> GSI 11 (level, low) ->
IRQ 11
[drm] Initialized radeon 1.25.0 20060524 on minor 0
mtrr: 0xf0000000,0x8000000 overlaps existing 0xf0000000,0x4000000
mtrr: 0xf0000000,0x8000000 overlaps existing 0xf0000000,0x4000000
mtrr: 0xf0000000,0x8000000 overlaps existing 0xf0000000,0x4000000
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:05.0 into 8x mode
[drm] Setting GART location based on old memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
ath0: no IPv6 routers present
-------------------------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier.
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Suspend-devel mailing list
Suspend-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/suspend-devel
