> On 4. Jan 2018, at 23:37, Kyle Evans <kev...@freebsd.org> wrote:
>
> Author: kevans
> Date: Thu Jan 4 22:37:15 2018
> New Revision: 327563
> URL: https://svnweb.freebsd.org/changeset/base/327563
>
> Log:
> if_awg: Use syscon prop if it exists
>
> The emac bindings that are landing in Linux 4.15 specify a syscon property
> on the emac node that point to /soc/syscon. Use this property if it's
> specified, but maintain backwards compatibility with the old method.
>
> The older method is still used for boards that we get .dtb from u-boot, such
> as pine64, that did not yet have stable emac bindings.
>
> Tested on: Banana Pi-M3 (a83t)
> Tested on: Pine64 (a64)
> Reviewed by: manu
> Differential Revision: https://reviews.freebsd.org/D13296
This breaks booting on a RPi3. Please note that it is not only panic'ing,
but there are multiple errors before that.
>> FreeBSD EFI boot block
Loader path: /boot/loader.efi
Initializing modules: UFS
Probing 3 block devices.....* done
UFS found 1 partition
Consoles: EFI console
Command line arguments: loader.efi
Image base: 0x39ab8008
EFI version: 2.05
EFI Firmware: Das U-boot (rev 0.00)
FreeBSD/arm64 EFI loader, Revision 1.1
(Wed Dec 6 19:13:14 CET 2017 r...@bsd18.fh-muenster.de)
EFI boot environment
Loading /boot/defaults/loader.conf
/boot/kernel/kernel text=0x7f3b28 data=0xaac80+0x3a106d
syms=[0x8+0x10e870+0x8+0x101345]
/boot/entropy size=0x1000
/boot/kernel/geom_label.ko text=0x2a80 text=0x2710 data=0x10118+0xfeec
syms=[0x8+0x1548+0x8+0xef2]
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by EFI at 0x8004000.
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-CURRENT #21 r327563M: Sat Jan 6 14:16:20 CET 2018
tue...@bsd10.fh-muenster.de:/usr/home/tuexen/head/sys/arm64/compile/TCP
arm64
FreeBSD clang version 5.0.1 (branches/release_50 319231) (based on LLVM 5.0.1)
VT: init without driver.
sysctl_warn_reuse: can't re-use a leaf (kern.features.geom_label)!
module_register: cannot register g_label from kernel; already loaded from
geom_label.ko
Module g_label failed to register: 17
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
module_register_init: MOD_LOAD (efirt, 0xffff0000000cb414, 0) error 12
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
ofw_clkbus0: <OFW clocks bus> on ofwbus0
clk_fixed0: <Fixed clock> on ofw_clkbus0
clk_fixed1: <Fixed clock> on ofw_clkbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
syscon_generic0: <syscon> mem 0x40000000-0x400000ff on simplebus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
local_intc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on
simplebus0
local_intc0: could not allocate memory resource
device_attach: local_intc0 attach returned 6
intc0: <BCM2835 Interrupt Controller> mem 0x7e00b200-0x7e00b3ff irq 16 on
simplebus0
local_intc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on
simplebus0
local_intc0: could not allocate memory resource
device_attach: local_intc0 attach returned 6
local_intc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on
simplebus0
local_intc0: could not allocate memory resource
device_attach: local_intc0 attach returned 6
local_intc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on
simplebus0
local_intc0: could not allocate memory resource
device_attach: local_intc0 attach returned 6
generic_timer0: <ARMv7 Generic Timer> irq 47,48,49,50 on simplebus0
generic_timer0: could not allocate resources
device_attach: generic_timer0 attach returned 6
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007eff irq
0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15 on simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100027 on simplebus0
bcmrng0: <Broadcom BCM2835 RNG> mem 0x7e104000-0x7e10400f on simplebus0
device_attach: bcmrng0 attach returned 6
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 17 on
simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 18,19 on
simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpioc0: <GPIO controller> on gpio0
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e201fff irq 20 on simplebus0
uart0: console (115200,n,8,1)
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e204fff irq 21 on
simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 32 on
simplebus0
bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem
0x7e980000-0x7e98ffff,0x7e006000-0x7e006fff irq 38,39 on simplebus0
usbus0 on bcm283x_dwcotg0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 42
on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fbd0 on fb0
VT: initialize with new VT driver "fb".
fb0: 656x416(656x416@0,0) 24bpp
fb0: fbswap: 1, pitch 1968, base 0x3db33000, screen_size 818688
local_intc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on
simplebus0
local_intc0: could not allocate memory resource
device_attach: local_intc0 attach returned 6
pmu0: <Performance Monitoring Unit> irq 46 on simplebus0
pmu0: could not allocate resources
device_attach: pmu0 attach returned 6
generic_timer0: <ARMv7 Generic Timer> irq 47,48,49,50 on simplebus0
generic_timer0: could not allocate resources
device_attach: generic_timer0 attach returned 6
gpioled0: <GPIO LEDs> on ofwbus0
gpioled0: <led0> failed to map pin
gpioled0: <led1> failed to map pin
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
cryptosoft0: <software crypto>
panic: No usable event timer found!
cpuid = 0
time = 1
KDB: stack backtrace:
db_trace_self() at db_trace_self_wrapper+0x28
pc = 0xffff00000062b308 lr = 0xffff000000086b78
sp = 0xffff0000000107c0 fp = 0xffff0000000109d0
db_trace_self_wrapper() at vpanic+0x184
pc = 0xffff000000086b78 lr = 0xffff0000003258a4
sp = 0xffff0000000109e0 fp = 0xffff000000010a60
vpanic() at panic+0x44
pc = 0xffff0000003258a4 lr = 0xffff00000032571c
sp = 0xffff000000010a70 fp = 0xffff000000010af0
panic() at cpu_initclocks_bsp+0x410
pc = 0xffff00000032571c lr = 0xffff00000066a6ec
sp = 0xffff000000010b00 fp = 0xffff000000010b50
cpu_initclocks_bsp() at initclocks+0x28
pc = 0xffff00000066a6ec lr = 0xffff0000002c4b9c
sp = 0xffff000000010b60 fp = 0xffff000000010b60
initclocks() at mi_startup+0xc8
pc = 0xffff0000002c4b9c lr = 0xffff0000002c148c
sp = 0xffff000000010b70 fp = 0xffff000000010bb0
mi_startup() at virtdone+0x54
pc = 0xffff0000002c148c lr = 0xffff000000001084
sp = 0xffff000000010bc0 fp = 0x0000000000000000
KDB: enter: panic
[ thread pid 0 tid 100000 ]
Stopped at 0
db>
Revision 327562 boots fine:
Using DTB provided by EFI at 0x8004000.
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-CURRENT #19 r327562M: Sat Jan 6 14:00:01 CET 2018
tue...@bsd10.fh-muenster.de:/usr/home/tuexen/head/sys/arm64/compile/TCP
arm64
FreeBSD clang version 5.0.1 (branches/release_50 319231) (based on LLVM 5.0.1)
VT: init without driver.
sysctl_warn_reuse: can't re-use a leaf (kern.features.geom_label)!
module_register: cannot register g_label from kernel; already loaded from
geom_label.ko
Module g_label failed to register: 17
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
random: unblocking device.
module_register_init: MOD_LOAD (efirt, 0xffff0000000cb414, 0) error 12
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
ofw_clkbus0: <OFW clocks bus> on ofwbus0
clk_fixed0: <Fixed clock> on ofw_clkbus0
clk_fixed1: <Fixed clock> on ofw_clkbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
local_intc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on
simplebus0
intc0: <BCM2835 Interrupt Controller> mem 0x7e00b200-0x7e00b3ff irq 16 on
simplebus0
generic_timer0: <ARMv7 Generic Timer> irq 47,48,49,50 on simplebus0
Timecounter "ARM MPCore Timecounter" frequency 19200000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 19200000 Hz quality 1000
bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007eff irq
0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15 on simplebus0
bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100027 on simplebus0
bcmrng0: <Broadcom BCM2835 RNG> mem 0x7e104000-0x7e10400f on simplebus0
device_attach: bcmrng0 attach returned 6
mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 17 on
simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 18,19 on
simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpioc0: <GPIO controller> on gpio0
uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e201fff irq 20 on simplebus0
uart0: console (115200,n,8,1)
spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e204fff irq 21 on
simplebus0
spibus0: <OFW SPI bus> on spi0
spibus0: <unknown card> at cs 0 mode 0
spibus0: <unknown card> at cs 1 mode 0
iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 32 on
simplebus0
bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem
0x7e980000-0x7e98ffff,0x7e006000-0x7e006fff irq 38,39 on simplebus0
usbus0 on bcm283x_dwcotg0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 42
on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
fb0: <BCM2835 VT framebuffer driver> on simplebus0
fbd0 on fb0
VT: initialize with new VT driver "fb".
fb0: 656x416(656x416@0,0) 24bpp
fb0: fbswap: 1, pitch 1968, base 0x3db33000, screen_size 818688
pmu0: <Performance Monitoring Unit> irq 46 on simplebus0
gpioled0: <GPIO LEDs> on ofwbus0
gpioled0: <led0> failed to map pin
gpioled0: <led1> failed to map pin
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert loadable, nat loadable, default to accept,
logging disabled
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
The GEOM class LABEL is already loaded.
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <DWCOTG OTG Root HUB> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
mmcsd0: 64GB <SDHC SC64G 8.0 SN F17A3CC6 MFG 11/2016 by 3 SD> at mmc0
41.6MHz/4bit/65535-block
bcm2835_cpufreq0: ARM 600MHz, Core 250MHz, SDRAM 400MHz, Turbo OFF
Release APs
CPU 0: ARM Cortex-A53 r0p4 affinity: 0
Instruction Set Attributes 0 = <CRC32>
Instruction Set Attributes 1 = <>
Processor Features 0 = <AdvSIMD,Float,EL3 32,EL2 32,EL1 32,EL0 32>
Processor Features 1 = <0>
Memory Model Features 0 = <4k Granule,64k Granule,MixedEndian,S/NS
Mem,16bit ASID,1TB PA>
Memory Model Features 1 = <>
Memory Model Features 2 = <32b CCIDX,48b VA>
Debug Features 0 = <2 CTX Breakpoints,4 Watchpoints,6
Breakpoints,PMUv3,Debug v8>
Debug Features 1 = <0>
Auxiliary Features 0 = <0>
Auxiliary Features 1 = <0>
CPU 1: ARM Cortex-A53 r0p4 affinity: 1
CPU 2: ARM Cortex-A53 r0p4 affinity: 2
CPU 3: ARM Cortex-A53 r0p4 affinity: 3
Trying to mount root from ufs:/dev/mmcsd0s2a [rw,noatime]...
Warning: no time-of-day clock registered, system time will not be set accurately
uhub0: 1 port with 1 removable, self powered
sysctl: net.inet.sctp.udp_tunneling_port=9899 at line 11: Can't assign
requested address
Setting hostuuid: 30303030-3030-3030-3138-303365396335.
Setting hostid: 0xede1b97d.
No suitable dump device was found.
Starting file system checks:
/dev/mmcsd0s2a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/mmcsd0s2a: clean, 12823920 free (74496 frags, 1593678 blocks, 0.5%
fragmentation)
ugen0.2: <vendor 0x0424 product 0x9514> at usbus0
uhub1 on uhub0
uhub1: <vendor 0x0424 product 0x9514, class 9/0, rev 2.00/2.00, addr 2> on
usbus0
uhub1: MTT enabled
Mounting local filesystems:.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib
/usr/local/lib/perl5/5.24/mach/CORE
uhub1: 5 ports with 4 removable, self powered
Setting hostname: bsd10.fh-muenster.de.
Setting up harvesting:
[UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED
Feeding entropy: .
ugen0.3: <vendor 0x0424 product 0xec00> at usbus0
smsc0 on uhub1
smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0
smsc0: chip 0xec00, rev. 0002
miibus0: <MII bus> on smsc0
smscphy0: <SMC LAN8700 10/100 interface> PHY 1 on miibus0
smscphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ue0: <USB Ethernet> on smsc0
ue0: Ethernet address: b8:27:eb:03:e9:c5
Starting Network: lo0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
groups: lo
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
Starting devd.
ue0: link state changed to UP
smsc0: chip 0xec00, rev. 0002
ue0: link state changed to DOWN
ue0: link state changed to UP
Starting Network: ue0.
ue0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=80009<RXCSUM,VLAN_MTU,LINKSTATE>
ether b8:27:eb:03:e9:c5
inet 212.201.121.100 netmask 0xffffffe0 broadcast 212.201.121.127
inet6 fe80::ba27:ebff:fe03:e9c5%ue0 prefixlen 64 scopeid 0x2
inet6 2a02:c6a0:4015:10::100 prefixlen 64
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
add net default: gateway 212.201.121.97
add host 127.0.0.1: gateway lo0 fib 0: route already in table
add net default: gateway 212.201.121.97 fib 0: route already in table
add host ::1: gateway lo0 fib 0: route already in table
add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
add net default: gateway fe80::a236:9fff:fe80:e9de%ue0
Creating and/or trimming log files.
Starting syslogd.
Setting date via ntp.
6 Jan 14:20:41 ntpdate[526]: step time server 204.9.54.119 offset 84.882792 sec
Clearing /tmp (X related).
Updating motd:.
Mounting late filesystems:.
Starting thttpd.
Configuring vt: blanktime.
Performing sanity check on sshd configuration.
Starting sshd.
Starting cron.
Starting background file system checks in 60 seconds.
Sat Jan 6 14:20:42 CET 2018
FreeBSD/arm64 (bsd10.fh-muenster.de) (ttyu0)
login:
The kernel config being used is:
include GENERIC-NODEBUG
ident TCP
makeoptions WITH_EXTRA_TCP_STACKS=1
options TCP_RFC7413
options IPFIREWALL
options IPFIREWALL_VERBOSE
options IPFIREWALL_VERBOSE_LIMIT=5
options IPFIREWALL_DEFAULT_TO_ACCEPT
nooptions COMPAT_FREEBSD32
Best regards
Michael
_______________________________________________
svn-src-head@freebsd.org mailing list
https://lists.freebsd.org/mailman/listinfo/svn-src-head
To unsubscribe, send any mail to "svn-src-head-unsubscr...@freebsd.org"
