Well...watchguard hacking continues (o;
After figuring out that junos needs at least 256MB
RAM for installation and a Firebox 2 supports 256MB
I am in need for at least 2 Intel EtherExpress
Pro 100 PCI cards as Juniper only supports
Intel and certain Broadcom chipsets now...
The rest is fine (o;
Copyright (c) 1996-2001, Juniper Networks, Inc.
All rights reserved.
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
JUNOS 7.0R2.7 #0: 2005-01-06 06:58:15 UTC
[EMAIL PROTECTED]:/build/benten-c/7.0R2.7/obj-i386/sys/compile/JUNI
PER
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 200455806 Hz
CPU: Pentium/P55C (200.46-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x543 Stepping = 3
Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
real memory = 268435456 (262144K bytes)
FreeBSD Kernel Configuration Utility - Version 1.2
Type "help" for help or "visual" to go to the visual
configuration interface (requires MGA/VGA display or
serial terminal capable of displaying ANSI graphics).
config> di psm0
config> q
sio0: gdb debugging port
avail memory = 253788160 (247840K bytes)
Preloaded elf kernel "kernel" at 0xc06de000.
Intel Pentium detected, installing workaround for F00F bug
DEVFS: ready for devices
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfcd0-0xfcdf at device 7.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 15
smb0: <Intel 82371AB SMB controller> port 0x1040-0x104f at device 7.3 on
pci0
pci0: <unknown card> (vendor=0x1011, dev=0x0019) at 13.0 irq 10
pci0: <unknown card> (vendor=0x1011, dev=0x0019) at 14.0 irq 11
pci0: <unknown card> (vendor=0x1011, dev=0x0019) at 15.0 irq 9
pcic-pci0: <TI PCI-1225 PCI-CardBus Bridge> at device 16.0 on pci0
pcic-pci0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr
save][CSC se
rial isa irq]
pcic-pci1: <TI PCI-1225 PCI-CardBus Bridge> at device 16.1 on pci0
pcic-pci1: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr
save][CSC se
pci0: <S3 Trio 64V2/DX/GX graphics accelerator> at 18.0 irq 15
fdc0: direction bit not set
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd0000 irq 10 on isa0
pcic0: management irq 10
pccard0: <PC Card bus -- legacy version> on pcic0
pccard1: <PC Card bus -- legacy version> on pcic0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x90 on isa0
sio0: type 16550A, console
sio1: configured irq 5 not in bitmap of probed irqs 0
sio2 at port 0x2f8-0x2ff irq 3 on isa0
sio2: type 16550A
sio3: configured irq 7 not in bitmap of probed irqs 0
DEVFS: ready to run
ad0: 11513MB <FUJITSU MHK2120AT> [23392/16/63] at ata0-master using UDMA33
ad1: 7MB <> [248/2/32] at ata0-slave using PIO2
[EMAIL PROTECTED]
nice weekend
rick
_______________________________________________
swinog mailing list
[email protected]
http://lists.swinog.ch/cgi-bin/mailman/listinfo/swinog
