09.12.07, Konstantin A. Lepikhov<lakostis@> написал(а): > Hi! > > Кому-нибудь удавалось завести AP на b43? Интересует ядро > 2.6.23 и > hostapd >0.6.0. У меня пока остановилось на след.: > > ... > Using interface wlan0_rename with hwaddr xx:xx:xx:xx:xx:xx and ssid > 'homenet' > 1197228746.877531: SSID - hexdump_ascii(len=7): > xxxxxxxxxxxxxxxxxxxx xxxxxx > 1197228746.877766: PSK (ASCII passphrase) - hexdump_ascii(len=11): > xxxxxxxxxxxxxxxxxxxxx xxxxxxx > 1197228747.407432: PSK (from passphrase) - hexdump(len=32): xx xx ... > 1197228748.481392: WPA: group state machine entering state > GTK_INIT (VLAN-ID 0) > 1197228748.483420: GMK - hexdump(len=32): [REMOVED] > 1197228748.485260: GTK - hexdump(len=32): [REMOVED] > 1197228748.486967: WPA: group state machine entering state SETKEYSDONE > (VLAN-ID 0) > wlan0_rename: ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported > 1197228748.496249: Could not set PrivacyInvoked for interface wlan0_rename > 1197228748.497995: wlan0_rename: Unable to setup interface. > 1197228748.499895: Flushing old station entries > Could not connect to kernel driver. > 1197228748.503947: Deauthenticate all stations > rmdir[ctrl_interface]: No such file or directory > wlan0_rename: ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported > 1197228748.518327: Could not disable PrivacyInvoked for interface wlan0_rename > > в это время в dmesg видно след.: > b43-phy0 debug: Loading firmware version 351.126 (2006-07-29 05:54:02) > b43-phy0 debug: Chip initialized > b43-phy0 debug: 32-bit DMA initialized > b43-phy0 debug: Wireless interface started > b43-phy0 debug: Adding Interface type 1 > br-lan: port 2(wlan0_rename) entering learning state > b43-phy0 debug: Removing Interface type 1 > b43-phy0 debug: Wireless interface stopped > b43-phy0 debug: DMA-32 0x0200 (RX) max used slots: 0/64 > b43-phy0 debug: DMA-32 0x02A0 (TX) max used slots: 0/128 > b43-phy0 debug: DMA-32 0x0280 (TX) max used slots: 0/128 > b43-phy0 debug: DMA-32 0x0260 (TX) max used slots: 0/128 > b43-phy0 debug: DMA-32 0x0240 (TX) max used slots: 0/128 > b43-phy0 debug: DMA-32 0x0220 (TX) max used slots: 0/128 > b43-phy0 debug: DMA-32 0x0200 (TX) max used slots: 0/128 > br-lan: port 2(wlan0_rename) entering disabled state > > т.е. где-то падает wpa, но не знаю где :( Без авторизации вроде бы > запускается, но клиенты эту AP не видят (с AP видно броадкасты, но не > более того, STA за свою оно не признает). > > конфиг /etc/hostapd/hostapd.conf: > > interface=wlan0_rename > driver=devicescape > logger_syslog=-1 > logger_syslog_level=2 > logger_stdout=-1 > logger_stdout_level=2 > debug=4 > dump_file=/tmp/hostapd.dump > ctrl_interface=/var/run/hostapd > ssid=homenet > hw_mode=g > macaddr_acl=1 > accept_mac_file=/etc/hostapd/accept > auth_algs=3 > ignore_broadcast_ssid=0 > #eap_message=hello > #wep_key_len_broadcast=5 > #wep_key_len_unicast=5 > eapol_key_index_workaround=1 > #eap_server=1 > wpa=1 > wpa_passphrase=xxxxxxx > wpa_psk_file=/etc/hostapd/accept.wpa_psk > wpa_key_mgmt=WPA-PSK WPA-EAP > passive_scan_mode=0 > > PS Это не альт, и вообще не i586. Это debian mipsel на wl500gP, но думаю > для решения проблемы не суть важно.
А уже сделали рабочий b43? Тогда интресно - буду смотреть. (в родной и Олеговской прошивке закрытый модуль используется). А вместо hotapd пробовали nas использовать? И ещё подскажите, почему debian, а не openwrt? вот ещё, может что подскажет. http://forum.openwrt.org/viewtopic.php?id=6090 -- Alexey Shabalin _______________________________________________ Sysadmins mailing list [email protected] https://lists.altlinux.org/mailman/listinfo/sysadmins
