You probably need to clear the At. Put an At"" after each If conditional.
Henry Taylor
Technical Analyst II
Lutheran Health Network
Ph. (260) 425-3914
|--------+-------------------------------->
| | "White, Scott A" |
| | <[EMAIL PROTECTED]|
| | RG> |
| | Sent by: |
| | [EMAIL PROTECTED]|
| | TATION.COM |
| | |
| | |
| | 10/21/2004 03:27 PM |
| | Please respond to Talk|
| | |
|--------+-------------------------------->
>-----------------------------------------------------------------------------------------------------------|
|
|
| To: <[EMAIL PROTECTED]>
|
| cc:
|
| Subject: RE: [Talk] Variable not updating
|
>-----------------------------------------------------------------------------------------------------------|
Oddly enough,
I used this logic, which did make the : go away.
Now the script produces random RESULTS..... even when a device is not in
use
I still get the Else statement to evaluate and populate the message.
Thank you for helping me to get rid of the : though.
Still need the system to actually evaluate the If, Then, Else statement
correctly.
Very strange?!?!?!?!???
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of Larry Briggs
Sent: Thursday, October 21, 2004 4:11 PM
To: [EMAIL PROTECTED]
Subject: RE: [Talk] Variable not updating
can you change
...
Else: M1Result = "Modem.1 is in use on " & mydate
End If
to
...
Else
M1Result = "Modem.1 is in use on " & mydate
End If
?
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of White,
Scott A
Sent: Thursday, October 21, 2004 4:08 PM
To: [EMAIL PROTECTED]
Subject: RE: [Talk] Variable not updating
Yes; but each time I tried to take the : out after the Else,
VB would put it back in again.
I'm stumped!!!!
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] Behalf Of
Adams,Ernest
Sent: Thursday, October 21, 2004 4:02 PM
To: '[EMAIL PROTECTED]'
Subject: RE: [Talk] Variable not updating
Scott:
The problem is the colon following the Else. VB thinks
"Else:" is a label rather than an else clause of the If.
Pax,
Ernest 21 Oct 04
-----Original Message-----
From: White, Scott A
[mailto:[EMAIL PROTECTED]
Sent: Thursday, October 21, 2004 3:55 PM
To: [EMAIL PROTECTED]
Subject: [Talk] Variable not updating
Hello,
I've got a small script that runs well except for
the result of M2Result and M3Result
seen below. The script will run and send the
results to me in MOX; but it ALWAYS
sends me the Modem.2 is in use on " & mydate and
Modem.3 is in use on " & mydate
Oddly enough, Modem.1 sends the correct info. Can
you tell by looking at this, why it
wouldn't evaluate the If statements? None of the
devices have been in use all day; but
my script ignores that for Modem.2 and Modem.3 .
I've even initialized all three at the
beginning of the procedure.
Pause "Device"
Enter "MODEM.1"
Wait 2
If At("Device is not in use") Then
M1Result = "Modem.1 Not In use at this time"
Else: M1Result = "Modem.1 is in use on " &
mydate
End If
Key "{F11}"
Wait 1
Enter "MODEM.2"
Wait 2
If At("Device is not in use") Then
M2Result = "Modem.2 Not In use at this
time"
Else: M2Result = "Modem.2 is in use on "
& mydate
End If
Key "{F11}"
Wait 1
Enter "MODEM.3"
Wait 2
If At("Device is not in use")
Then
M3Result = "Modem.3 Not In use
at this time"
Else: M3Result = "Modem.3 is in
use on " & mydate
End If
Key "{F11}"
Wait 1
Thank you,
Scott
CONFIDENTIALITY NOTICE: This e-mail communication
and any attachments
may contain confidential and privileged information
for the use of the
designated recipients named above. If you are not
the intended
recipient, you are hereby notified that you have
received this communication in
error and that any review, disclosure,
dissemination, distribution or copying
of it or its contents is prohibited. If you have
received this
communication in error, please notify Saratoga
Hospital immediately by e-mail at
[EMAIL PROTECTED] and destroy all copies of
this communication
and any attachments.
CONFIDENTIALITY NOTICE: This e-mail message, including any
attachments, is for the sole use of the intended recipient(s) and
may contain confidential and privileged information. Any
unauthorized review, use, disclosure or distribution is prohibited.
ZirMed, Inc. has strict policies regarding the content of e-mail
communications, specifically Protected Health Information, any
communications containing such material will be returned to the
originating party with such advisement noted. If you are not the
intended recipient, please contact the sender by reply e-mail and
destroy all copies of the original message.
