Hallo Heiner, hallo Liste, das erw�hnte kanotix liefert auf der gleichen Maschine (!) folgenden Output von dmesg:
eth0: RealTek RTL8139 at 0xe0cc2000, 00:30:84:74:4c:3c, IRQ 11 eth0: Identified 8139 chip type 'RTL-8139C' input: PC Speaker eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 NET: Registered protocol family 17 ACPI: PCI interrupt 0000:00:07.5[C] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:07.5 to 64 CAPI Subsystem Rev 1.1.2.8 capifs: Rev 1.1.2.3 capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs) fcpci: module license 'Proprietary' taints kernel. fcpci: AVM FRITZ!Card PCI driver, revision 0.6.2 fcpci: (fcpci built on Nov 26 2004 at 15:33:22) ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 10 (level, low) -> IRQ 10 fcpci: AVM FRITZ!Card PCI found: port 0xc000, irq 10 fcpci: Loading... fcpci: Driver 'fcpci' attached to stack. (152) fcpci: Stack version 3.11-02 kcapi: Controller 1: fcpci-c000-10 attached kcapi: card 1 "fcpci-c000-10" ready. fcpci: Loaded. FAT: Unrecognized mount option "uid=knoppix" or missing value FAT: Unrecognized mount option "uid=knoppix" or missing value FAT: Unrecognized mount option "uid=knoppix" or missing value lp0: using parport0 (polling). lp0: console ready ts: Compaq touchscreen protocol output Mandrake 9.2 dagegen schimpft - mit mir ? "HiSax: Approval certification failed because of HiSax: unauthorized source code changes" dmesg-output Mandrake 9.2 ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded HiSax: Linux Driver for passive ISDN cards HiSax: Version 3.5 (module) HiSax: Layer1 Revision 1.1.4.1 HiSax: Layer2 Revision 1.1.4.1 HiSax: TeiMgr Revision 1.1.4.1 HiSax: Layer3 Revision 1.1.4.1 HiSax: LinkLayer Revision 1.1.4.1 HiSax: Approval certification failed because of HiSax: unauthorized source code changes HiSax: Total 1 card defined HiSax: Card 1 Protocol EDSS1 Id=HiSax (0) HiSax: AVM PCI driver Rev. 1.1.4.1 FritzPnP: no ISA PnP present PCI: Found IRQ 10 for device 00:0c.0 AVM PCI: stat 0x3020a AVM PCI: Class A Rev 2 HiSax: AVM Fritz!PCI config irq:10 base:0xC000 AVM PCI: ISAC version (0): 2086/2186 V1.1 AVM Fritz PnP/PCI: IRQ 10 count 0 AVM Fritz PnP/PCI: IRQ 10 count 3 HiSax: DSS1 Rev. 1.1.4.1 HiSax: 2 channels added HiSax: MAX_WAITING_CALLS added HiSax: debugging flags card 1 set to 4 isdn: Verbose-Level is 2 -- [EMAIL PROTECTED] ---------------------------------------------------------------------------- PUG - Penguin User Group Wiesbaden - http://www.pug.org
