Here is a diff to add flow control support to vge(4).
Tested with..
vge0 at pci2 dev 4 function 0 "VIA VT612x" rev 0x11
ciphy0 at vge0 phy 1: CS8201 10/100/1000TX PHY, rev. 1
OK?
Index: if_vge.c
===================================================================
RCS file: /home/cvs/src/sys/dev/pci/if_vge.c,v
retrieving revision 1.51
diff -u -p -r1.51 if_vge.c
--- if_vge.c 22 Jun 2011 16:44:27 -0000 1.51
+++ if_vge.c 22 Oct 2012 08:22:55 -0000
@@ -812,7 +812,7 @@ vge_attach(struct device *parent, struct
ifmedia_init(&sc->sc_mii.mii_media, 0,
vge_ifmedia_upd, vge_ifmedia_sts);
mii_attach(self, &sc->sc_mii, 0xffffffff, MII_PHY_ANY,
- MII_OFFSET_ANY, 0);
+ MII_OFFSET_ANY, MIIF_DOPAUSE);
if (LIST_FIRST(&sc->sc_mii.mii_phys) == NULL) {
printf("%s: no PHY found!\n", sc->vge_dev.dv_xname);
ifmedia_add(&sc->sc_mii.mii_media, IFM_ETHER|IFM_MANUAL,
@@ -1630,9 +1630,16 @@ vge_init(struct ifnet *ifp)
/* Init the multicast filter. */
vge_setmulti(sc);
- /* Enable flow control */
-
- CSR_WRITE_1(sc, VGE_CRS2, 0x8B);
+ /* Initialize pause timer. */
+ CSR_WRITE_2(sc, VGE_TX_PAUSE_TIMER, 0xFFFF);
+ /*
+ * Initialize flow control parameters.
+ * TX XON high threshold : 48
+ * TX pause low threshold : 24
+ * Disable half-duplex flow control
+ */
+ CSR_WRITE_1(sc, VGE_CRC2, 0xFF);
+ CSR_WRITE_1(sc, VGE_CRS2, VGE_CR2_XON_ENABLE | 0x0B);
/* Enable jumbo frame reception (if desired) */
@@ -1768,6 +1775,16 @@ vge_miibus_statchg(struct device *dev)
sc->vge_dev.dv_xname, IFM_SUBTYPE(ife->ifm_media));
break;
}
+
+ /*
+ * 802.3x flow control
+ */
+ CSR_WRITE_1(sc, VGE_CRC2, VGE_CR2_FDX_TXFLOWCTL_ENABLE |
+ VGE_CR2_FDX_RXFLOWCTL_ENABLE);
+ if ((IFM_OPTIONS(mii->mii_media_active) & IFM_ETH_TXPAUSE) != 0)
+ CSR_WRITE_1(sc, VGE_CRS2, VGE_CR2_FDX_TXFLOWCTL_ENABLE);
+ if ((IFM_OPTIONS(mii->mii_media_active) & IFM_ETH_RXPAUSE) != 0)
+ CSR_WRITE_1(sc, VGE_CRS2, VGE_CR2_FDX_RXFLOWCTL_ENABLE);
}
int
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.