Hey tech@,
At my wits end here, I recently got a sunfire v120 from work for pretty cheap.
Quite excited to have some non x86 hardware, I set it up as a router.
However, for some reason after sometimes mere hours -- othertimes days at a
time, the gem0 interface needs to be cycled:
ifconfig gem0 down
ifconfig gem0 up
dhclient gem0
no packets pass until that has been done. At first I have been placing the
blame squarely on the Hitron modem we have in the house from shaw cable,
but now I've noticed the issue happen twice on the internal interface as well,
gem1. All VLANs I have setup stop responding until gem1 is cycled.
gem1 is just used by a collection of vlan(4) interfaces, so traffic resumes
immediately after interface gem1 down/up.
I've tried to turn on ifconfig gem0 debug to catch anything wierd, but there
has been nothing of interest there. Dmesg attached, starting to wonder
if this machine is at its EOL and the network ports are dying :(
This issue occurred with the 5.7 release as well.
dmesg:
console is /pci@1f,0/pci@1,1/isa@7/serial@0,3f8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2015 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.8 (GENERIC) #0: Thu Oct 22 00:24:09 PDT 2015
r...@void.inter.lan:/usr/src/sys/arch/sparc64/compile/GENERIC
real mem = 1073741824 (1024MB)
avail mem = 1039228928 (991MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root: Sun Fire V120 (UltraSPARC-IIe 648MHz)
cpu0 at mainbus0: SUNW,UltraSPARC-IIe (rev 3.3) @ 648 MHz
cpu0: physical 16K instruction (32 b/l), 16K data (32 b/l), 512K external (64
b/l)
psycho0 at mainbus0: SUNW,sabre, impl 0, version 0, ign 7c0
psycho0: bus range 0-2, PCI bus 0
psycho0: dvma map c0000000-dfffffff
pci0 at psycho0
ppb0 at pci0 dev 1 function 1 "Sun Simba" rev 0x13
pci1 at ppb0 bus 1
ebus0 at pci1 dev 12 function 0 "Sun RIO EBus" rev 0x01
"flashprom" at ebus0 addr 0-fffff not configured
clock1 at ebus0 addr 0-1fff: mk48t59
lom0 at ebus0 addr 200000-200003 ivec 0x2a: LOMlite2 rev 3.12
alipm0 at pci1 dev 3 function 0 "Acer Labs M7101 Power" rev 0x00: 74KHz clock
iic0 at alipm0
"max1617" at alipm0 addr 0x18 skipped due to alipm0 bugs
spdmem0 at iic0 addr 0x54: 512MB SDRAM registered ECC PC133CL2
spdmem1 at iic0 addr 0x55: 512MB SDRAM registered ECC PC133CL2
ebus1 at pci1 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
power0 at ebus1 addr 2000-2007 ivec 0x25
com0 at ebus1 addr 3f8-3ff ivec 0x2b: ns16550a, 16 byte fifo
com0: console
com1 at ebus1 addr 2e8-2ef ivec 0x2b: ns16550a, 16 byte fifo
gem0 at pci1 dev 12 function 1 "Sun ERI Ether" rev 0x01: ivec 0x7c6, address
00:03:ba:2b:47:70
ukphy0 at gem0 phy 1: Generic IEEE 802.3u media interface, rev. 1: OUI
0x0010dd, model 0x0002
ohci0 at pci1 dev 12 function 3 "Sun USB" rev 0x01: ivec 0x7e4, version 1.0,
legacy support
pciide0 at pci1 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc3: DMA,
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using ivec 0x7cc for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <TEAC, CD-224E, P.9A> ATAPI 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 disabled (no drives)
gem1 at pci1 dev 5 function 1 "Sun ERI Ether" rev 0x01: ivec 0x7dc, address
00:03:ba:2b:47:71
ukphy1 at gem1 phy 1: Generic IEEE 802.3u media interface, rev. 1: OUI
0x0010dd, model 0x0002
ohci1 at pci1 dev 5 function 3 "Sun USB" rev 0x01: ivec 0x7e6, version 1.0,
legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Sun OHCI root hub" rev 1.00/1.00 addr 1
usb1 at ohci1: USB revision 1.0
uhub1 at usb1 "Sun OHCI root hub" rev 1.00/1.00 addr 1
ppb1 at pci0 dev 1 function 0 "Sun Simba" rev 0x13
pci2 at ppb1 bus 2
siop0 at pci2 dev 8 function 0 "Symbios Logic 53c896" rev 0x07: ivec 0x7e0,
using 8K of on-board RAM
scsibus2 at siop0: 16 targets, initiator 7
sym0 at scsibus2 targ 0 lun 0: <SEAGATE, ST336607LSUN36G, 0207> SCSI3 0/direct
fixed serial.SEAGATE_ST336607LSUN36G_3JA0DGN80000731804D9
sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST336607LSUN36G, 0207> SCSI3 0/direct
fixed serial.SEAGATE_ST336607LSUN36G_3JA0DGN80000731804D9
sd0: 34732MB, 512 bytes/sector, 71132959 sectors
probe(siop0:1:0): Check Condition (error 0x70) on opcode 0x0
SENSE KEY: Hardware Error
ASC/ASCQ: Defect List Error
FRU CODE: 0x7
sym1 at scsibus2 targ 1 lun 0: <SEAGATE, ST336607LSUN36G, 0207> SCSI3 0/direct
fixed serial.SEAGATE_ST336607LSUN36G_3JA0BZL100002316NCUL
sd1 at scsibus0 targ 1 lun 0: <SEAGATE, ST336607LSUN36G, 0207> SCSI3 0/direct
fixed serial.SEAGATE_ST336607LSUN36G_3JA0BZL100002316NCUL
siop1 at pci2 dev 8 function 1 "Symbios Logic 53c896" rev 0x07: ivec 0x7e0,
using 8K of on-board RAM
scsibus3 at siop1: 16 targets, initiator 7
siop0: target 0 now using tagged 16 bit 40.0 MHz 31 REQ/ACK offset xfers
vscsi0 at root
scsibus4 at vscsi0: 256 targets
softraid0 at root
scsibus5 at softraid0: 256 targets
siop0: target 1 now using tagged 16 bit 40.0 MHz 31 REQ/ACK offset xfers
bootpath: /pci@1f,0/pci@1,0/scsi@8,0/disk@0,0
root on sd0a (dd2dc38974492ea6.a) swap on sd0b dump on sd0b
