Hi, I'm trying to convert my SabreLite board to boot via efiboot, but without success so far.
I'm using the nitrogen6q u-boot from ports
the boot loader is loaded and runs but it
fails to find the sata disk to load the kernel:
=> fatload sata 0:1 0x10800000 efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65556 bytes read in 9 ms (6.9 MiB/s)
=> fatload sata 0:1 0x13000000 imx6q-sabrelite.dtb
reading imx6q-sabrelite.dtb
36834 bytes read in 8 ms (4.4 MiB/s)
=> bootefi 0x10800000 0x13000000
## Starting EFI application at 0x10800000 ...
Scanning disks on sata...
Scanning disks on usb...
Scanning disks on mmc...
MMC: no card present
MMC Device 2 not found
MMC Device 3 not found
Found 2 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
cannot open sd0a:/etc/random.seed: Device not configured
booting sd0a:/bsd: open sd0a:/bsd: Device not configured
failed(6). will try /bsd
boot>
Any idea ?
Below is a dmesg of a bsd.umg kernel booted the old way, with
imx6q-sabrelite.dtb loaded
OpenBSD 6.0-beta (GENERIC) #69: Sun Jun 5 14:21:01 CEST 2016
[email protected]:/usr/obj/GENERIC
real mem = 1073741824 (1024MB)
avail mem = 1044602880 (996MB)
warning: no entropy supplied by boot loader
mainbus0 at root: Freescale i.MX6 Quad SABRE Lite Board
cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
ampintc0 at cortex0 nirq 160
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
imx0 at mainbus0
imxccm0 at imx0: imx6 rev 1.2 CPU freq: 792 MHz
imxiomuxc0 at imx0
imxdog0 at imx0
imxocotp0 at imx0
imxuart0 at imx0 console
imxgpio0 at imx0
imxgpio1 at imx0
imxgpio2 at imx0
imxgpio3 at imx0
imxgpio4 at imx0
imxgpio5 at imx0
imxgpio6 at imx0
imxesdhc0 at imx0
imxesdhc0: 198 MHz base clock
sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma
imxesdhc1 at imx0
imxesdhc1: 198 MHz base clock
sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma
ehci0 at imx0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1
fec0 at imx0
fec0: address 00:19:b8:01:31:1c
ukphy0 at fec0 phy 6: Generic IEEE 802.3u media interface, rev. 1: OUI
0x000885, model 0x0021
ahci0 at imx0 AHCI 1.3
ahci0: port 0: 3.0Gb/s
scsibus0 at ahci0: 32 targets
sd0 at scsibus0 targ 0 lun 0: <ATA, Samsung SSD 840, EXT0> SCSI3 0/direct fixed
naa.50025388a00f2042
sd0: 114473MB, 512 bytes/sector, 234441648 sectors, thin
simplebus0 at mainbus0: "soc"
simplebus1 at simplebus0: "aips-bus"
simplebus2 at simplebus1: "spba-bus"
simplebus3 at simplebus1: "anatop"
simplebus4 at simplebus0: "aips-bus"
imxiic0 at simplebus4
iic0 at imxiic0
"fsl,sgtl5000" at iic0 addr 0xa not configured
imxiic1 at simplebus4
iic1 at imxiic1
imxiic2 at simplebus4
iic2 at imxiic2
simplebus5 at mainbus0: "regulators"
uhub1 at uhub0 port 1 "Standard Microsystems Hub" rev 2.00/b.b3 addr 2
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
boot device: lookup '' failed.
root device: sd0a
swap device (default sd0b):
root on sd0a swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
--
Matthieu Herrb
signature.asc
Description: PGP signature
