On Thu, Jul 21, 2016 at 01:06:50PM +1000, Jonathan Gray wrote:
>
> Actually the pad configuration in those commits may mean this isn't
> enough.
Hi,
I saw the r1.9 for if_fec.c and then it says it was tested on SABRE lite by
Patrick.
I tested on Wandboard Solo again. Now fec(4) shows up, however can't ping
anything. I can confirm it's not a network related issue, since I can ping from
within u-boot.
The leds on the Ethernet port are turned off. Maybe still something
related to this IRQ thing.
Thank you.
--
U-Boot SPL 2016.07 (Jul 20 2016 - 21:09:03)
Trying to boot from MMC1
U-Boot 2016.07 (Jul 20 2016 - 21:09:03 -0600)
CPU: Freescale i.MX6SOLO rev1.1 at 792 MHz
Reset cause: WDOG
Board: Wandboard rev B1
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
=> setenv ipaddr 192.168.1.24
=> ping 192.168.1.9
Using FEC device
host 192.168.1.9 is alive
=> reset
resetting ...
U-Boot SPL 2016.07 (Jul 20 2016 - 21:09:03)
Trying to boot from MMC1
U-Boot 2016.07 (Jul 20 2016 - 21:09:03 -0600)
CPU: Freescale i.MX6SOLO rev1.1 at 792 MHz
Reset cause: WDOG
Board: Wandboard rev B1
I2C: ready
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
reading /imx6dl-wandboard-revb1.dtb
29934 bytes read in 21 ms (1.4 MiB/s)
Found EFI removable media binary efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
65276 bytes read in 29 ms (2.1 MiB/s)
## Starting EFI application at 0x12000000 ...
Scanning disks on usb...
Scanning disks on mmc...
MMC Device 2 not found
MMC Device 3 not found
Found 6 disks
>> OpenBSD/armv7 BOOTARM 0.1
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2094412+7928824+428472 [64+297616+142910]=0xa64034
OpenBSD/armv7 booting ...
arg0 0x0 arg1 0x2e55b26c arg2 0x18000000
Allocating page tables
freestart = 0x10d65000, free_pages = 127643 (0x0001f29b)
IRQ stack: p0x10d93000 v0xc0d93000
ABT stack: p0x10d94000 v0xc0d94000
UND stack: p0x10d95000 v0xc0d95000
SVC stack: p0x10d96000 v0xc0d96000
Creating L1 page table at 0x10d68000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 240497260
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2016 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 6.0 (RAMDISK) #91: Sun Jul 24 16:10:29 AEST 2016
j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 536870912 (512MB)
avail mem = 512237568 (488MB)
mainbus0 at root: Wandboard i.MX6 Dual Lite Board rev B1
cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
ampintc0 at cortex0 nirq 160
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 8 waymask: 0x0000000f
imx0 at mainbus0
imxccm0 at imx0: imx6 rev 1.1 CPU freq: 792 MHz
imxiomuxc0 at imx0
imxocotp0 at imx0
simplebus0 at mainbus0: "soc"
simplebus1 at simplebus0: "aips-bus"
simplebus2 at simplebus1: "spba-bus"
imxuart0 at simplebus2: console
imxgpio0 at simplebus1
imxgpio1 at simplebus1
imxgpio2 at simplebus1
imxgpio3 at simplebus1
imxgpio4 at simplebus1
imxgpio5 at simplebus1
imxgpio6 at simplebus1
imxdog0 at simplebus1
simplebus3 at simplebus1: "anatop"
simplebus4 at simplebus0: "aips-bus"
imxehci0 at simplebus4
usb0 at imxehci0: USB revision 2.0
uhub0 at usb0 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1
imxehci1 at simplebus4
usb1 at imxehci1: USB revision 2.0
uhub1 at usb1 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1
fec0 at simplebus4
fec0: address 00:1f:7b:b0:08:52
atphy0 at fec0 phy 1: AR8035 10/100/1000 PHY, rev. 4
imxesdhc0 at simplebus4
imxesdhc0: 198 MHz base clock
sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma
imxesdhc1 at simplebus4
imxesdhc1: 198 MHz base clock
sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma
imxesdhc2 at simplebus4
imxesdhc2: 198 MHz base clock
sdmmc2 at imxesdhc2: 4-bit, mmc high-speed, dma
imxiic0 at simplebus4
iic0 at imxiic0
imxiic1 at simplebus4
iic1 at imxiic1
"fsl,sgtl5000" at iic1 addr 0xa not configured
imxuart1 at simplebus4
simplebus5 at mainbus0: "regulators"
sdmmc1: can't enable card
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, 00000, 0010> SCSI2 0/direct fixed
sd0: 1910MB, 512 bytes/sector, 3911680 sectors
scsibus1 at sdmmc2: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, SU08G, 0080> SCSI2 0/direct fixed
sd1: 7580MB, 512 bytes/sector, 15523840 sectors
boot device: sd0
root on rd0a swap on rd0b dump on rd0b
WARNING: CHECK AND RESET THE DATE!
erase ^?, werase ^W, kill ^U, intr ^C, status ^T
Welcome to the OpenBSD/armv7 6.0 installation program.
(I)nstall, (U)pgrade, (A)utoinstall or (S)hell? s
# ifconfig fec0 192.168.1.24 up
# ping 192.168.1.9
PING 192.168.1.9 (192.168.1.9): 56 data bytes
ping: sendto: Host is down
ping: wrote 192.168.1.9 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 192.168.1.9 64 chars, ret=-1
ping: sendto: Host is down
ping: wrote 192.168.1.9 64 chars, ret=-1
--- 192.168.1.9 ping statistics ---
9 packets transmitted, 0 packets received, 100.0% packet loss
#
--
db
