are you booting your USB drive in UEFI mode? or legacy?
d At 2016-12-12 02:43:32, "Bryan C. Everly" <[email protected]> wrote: >Hi tech@, > >I'm trying to install OpenBSD in a partition on this drive. I created >an OpenBSD type (0xa600) partition type with a GPT layout from Arch >Linux when I was installing it on this same hardware (I want to dual >boot using refind). > >You can see from the lsblk output on Linux below how things are structured: > >NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT >nvme0n1 259:0 0 953.9G 0 disk >├─nvme0n1p3 259:3 0 453.9G 0 part >├─nvme0n1p1 259:1 0 2G 0 part /boot >└─nvme0n1p2 259:2 0 498G 0 part > └─crypt 254:0 0 498G 0 crypt > ├─lvmpool-root 254:1 0 35G 0 lvm / > ├─lvmpool-swap 254:2 0 16G 0 lvm [SWAP] > └─lvmpool-home 254:3 0 447G 0 lvm /home > >When I boot the latest snapshot install60.fs USB drive (my preferred >method of installing), what I'm seeing looks like the drive is >recognized, but for some reason, disklabel is not seeing the right >data and says the OpenBSD area takes up the entire disk. My concern >is that if I install, it will whack the existing disk structure and >I'll lose my Linux install. > >I'd appreciate any advice on how to troubleshoot this. Here is the >output of disklabel, fdisk and dmesg: > >[# fdisk -v sd0] > >Primary GPT: >Disk: sd0 Usable LBA: 34 to 2000409230 [2000409265 Sectors] >GUID: e044f116-3aa6-4bb0-b06e-655c4f928486 > #: type [ start: size ] > guid name >------------------------------------------------------------------------ > 0: EFI Sys [ 2048: 4192257 ] > fba5492e-ddcd-40d5-afab-fce7f2886eef EFI System > 1: Linux files* [ 4196352: 1044379649 ] > a3a8a6d5-d881-4529-aab2-d383db3ebb2f Linux filesystem > 2: OpenBSD [ 1048578048: 951831183 ] > c004f9b9-5ec6-4841-89ec-6b5149a74810 OpenBSD disklabel > >Secondary GPT: > Not Found > >MBR: >Disk: sd0 geometry: 124519/255/63 [2000409265 Sectors] >Offset: 0 Signature: 0xAA55 > Starting Ending LBA Info: > #: id C H S - C H S [ start: size ] >------------------------------------------------------------------------------- > 0: EE 0 0 2 - 124519 182 63 [ 1: 2000409263 ] EFI GPT > 1: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused > 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused > 3: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused > >[#disklabel sd0] > ># /dev/rsd0c: >type: SCSI >disk: SCSI disk >label: SAMSUNG MZSLW1T0 >duid: 0000000000000000 >flags: >bytes/sector: 512 >sectors/track: 63 >tracks/cylinder: 255 >sectors/cylinder: 16065 >cylinders: 124519 >total sectors: 2000409265 >boundstart: 0 >boundend: 2000409265 >drivedata: 0 > >16 partitions: ># size offset fstype [fsize bsize cpg] > c: 2000409265 0 unused > >[#dmesg] > >OpenBSD 6.0-current (RAMDISK_CD) #21: Wed Dec 7 23:24:13 MST 2016 > [email protected]:/usr/src/sys/arch/amd64/compile/RAMDISK_CD >real mem = 16523563008 (15758MB) >avail mem = 16021069824 (15278MB) >mainbus0 at root >bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xd7c05000 (65 entries) >bios0: vendor LENOVO version "N1FET44W (1.18 )" date 09/01/2016 >bios0: LENOVO 20FBCTO1WW >acpi0 at bios0: rev 2 >acpi0: tables DSDT FACP TCPA SSDT UEFI SSDT SSDT ECDT HPET APIC MCFG >SSDT SSDT DBGP DBG2 BOOT BATB SLIC SSDT SSDT MSDM DMAR ASF! FPDT UEFI >acpiec0 at acpi0 >acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat >cpu0 at mainbus0: apid 0 (boot processor) >cpu0: Intel(R) Core(TM) i7-6600U CPU @ 2.60GHz, 2808.00 MHz >cpu0: >FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,HLE,AVX2,SMEP,BMI2,ERMS,INVPCID,RTM,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SENSOR,ARAT >cpu0: 256KB 64b/line 8-way L2 cache >cpu0: TSC frequency 2808000000 Hz >cpu0: apic clock running at 24MHz >cpu0: mwait min=64, max=64, C-substates=0.2.1.2.4.1.1.1, IBE >cpu at mainbus0: not configured >cpu at mainbus0: not configured >cpu at mainbus0: not configured >ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 120 pins >acpiprt0 at acpi0: bus 0 (PCI0) >acpiprt1 at acpi0: bus -1 (PEG0) >acpiprt2 at acpi0: bus -1 (PEG1) >acpiprt3 at acpi0: bus -1 (PEG2) >acpiprt4 at acpi0: bus 2 (EXP1) >acpiprt5 at acpi0: bus 4 (EXP3) >acpiprt6 at acpi0: bus 5 (EXP5) >acpiprt7 at acpi0: bus -1 (EXP9) >acpicpu at acpi0 not configured >acpipwrres at acpi0 not configured >acpipwrres at acpi0 not configured >acpipwrres at acpi0 not configured >acpipwrres at acpi0 not configured >acpipwrres at acpi0 not configured >acpipwrres at acpi0 not configured >acpitz at acpi0 not configured >"PNP0C0D" at acpi0 not configured >"PNP0C0E" at acpi0 not configured >"LEN0071" at acpi0 not configured >"LEN0058" at acpi0 not configured >"INT3F0D" at acpi0 not configured >"PNP0C0A" at acpi0 not configured >"ACPI0003" at acpi0 not configured >"LEN0068" at acpi0 not configured >"PNP0C60" at acpi0 not configured >"PNP0C14" at acpi0 not configured >"PNP0C14" at acpi0 not configured >"PNP0C14" at acpi0 not configured >"PNP0C14" at acpi0 not configured >"PNP0C31" at acpi0 not configured >"INT3394" at acpi0 not configured >pci0 at mainbus0 bus 0 >pchb0 at pci0 dev 0 function 0 "Intel Core 6G Host" rev 0x08 >vga1 at pci0 dev 2 function 0 "Intel HD Graphics 520" rev 0x07 >vga1: aperture needed >wsdisplay1 at vga1 mux 1: console (80x25, vt100 emulation) >"Intel Skylake GMM" rev 0x00 at pci0 dev 8 function 0 not configured >"Intel 100 Series ISH" rev 0x21 at pci0 dev 19 function 0 not configured >xhci0 at pci0 dev 20 function 0 "Intel 100 Series xHCI" rev 0x21: msi >usb0 at xhci0: USB revision 3.0 >uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev >3.00/1.00 addr 1 >"Intel 100 Series Thermal" rev 0x21 at pci0 dev 20 function 2 not configured >"Intel 100 Series MEI" rev 0x21 at pci0 dev 22 function 0 not configured >ppb0 at pci0 dev 28 function 0 "Intel 100 Series PCIE" rev 0xf1: msi >pci1 at ppb0 bus 2 >"Realtek RTS525A Card Reader" rev 0x01 at pci1 dev 0 function 0 not configured >ppb1 at pci0 dev 28 function 2 "Intel 100 Series PCIE" rev 0xf1: msi >pci2 at ppb1 bus 4 >iwm0 at pci2 dev 0 function 0 "Intel Dual Band Wireless AC 8260" rev 0x3a, msi >ppb2 at pci0 dev 28 function 4 "Intel 100 Series PCIE" rev 0xf1: msi >pci3 at ppb2 bus 5 >nvme0 at pci3 dev 0 function 0 vendor "Samsung", unknown product >0xa804 rev 0x00: msi, NVMe 1.1 >nvme0: SAMSUNG MZSLW1T0HMLH-000L1, firmware 3L0QCXY7, serial S308NX0HB01293 >scsibus0 at nvme0: 1 targets >sd0 at scsibus0 targ 0 lun 0: <NVMe, SAMSUNG MZSLW1T0, 3L0Q> SCSI4 >0/direct fixed >sd0: 976762MB, 512 bytes/sector, 2000409265 sectors >"Intel 100 Series LPC" rev 0x21 at pci0 dev 31 function 0 not configured >"Intel 100 Series PMC" rev 0x21 at pci0 dev 31 function 2 not configured >"Intel 100 Series HD Audio" rev 0x21 at pci0 dev 31 function 3 not configured >"Intel 100 Series SMBus" rev 0x21 at pci0 dev 31 function 4 not configured >em0 at pci0 dev 31 function 6 "Intel I219-LM" rev 0x21: msi, address >54:ee:75:b7:ac:ca >isa0 at mainbus0 >pckbc0 at isa0 port 0x60/5 irq 1 irq 12 >pckbd0 at pckbc0 (kbd slot) >wskbd0 at pckbd0: console keyboard, using wsdisplay1 >umass0 at uhub0 port 1 configuration 1 interface 0 "vendor 0x13fe >Patriot Memory" rev 2.00/1.00 addr 2 >umass0: using SCSI over Bulk-Only >scsibus1 at umass0: 2 targets, initiator 0 >sd1 at scsibus1 targ 1 lun 0: <, Patriot Memory, PMAP> SCSI2 0/direct >removable serial.13fe41003310A090C796 >sd1: 29557MB, 512 bytes/sector, 60532992 sectors >"vendor 0x8087 product 0x0a2b" rev 2.00/0.01 addr 3 at uhub0 port 7 >not configured >"Chicony Electronics Co.,Ltd. Integrated Camera" rev 2.00/0.04 addr 4 >at uhub0 port 8 not configured >"vendor 0x138a product 0x0090" rev 2.00/1.64 addr 5 at uhub0 port 9 >not configured >softraid0 at root >scsibus2 at softraid0: 256 targets >root on rd0a swap on rd0b dump on rd0b >iwm0: could not read firmware iwm-8000C-16 (error 2) >iwm0: failed to load init firmware >
