are you trying to add an i2c device to the sensor framework? or are you asking 
how to touch i2c devices from userland?

> On 21 Mar 2022, at 16:21, Dr. T.I.S. <[email protected]> wrote:
> 
> I know the rule, try to research first on man pages,  openbsd.org, ect,
> and ask people as a last resort. Unfortunately, I have exhausted
> all resources online that I could find. (I was recommend to use this
> email list by OpenBSd dev on reddit)
> 
> Currently, I am trying to use I2C on the latest version of aarch64 OpenBSD
> on
> RPI4. Are there any known drivers/libraries/userspace APIs to allow for
> that? Or, I would have to write my own drivers for rpi4b?
> 
> I found these two papers on openbsd.org  touching these two particular
> topics:
> 
> https://www.openbsd.org/papers/eurobsdcon2008-sensors.pdf
> 
> and
> 
> https://www.openbsd.org/papers/asiabsdcon2009-sensors-paper.pdf
> 
> However, my system lacks /sys/dev/i2c/i2c_scan.c or any other tool.
> 
> There are only headers files in the i2c directory:
> 
> /usr/include/dev/i2c/i2c_bitbang.h
> 
> /usr/include/dev/i2c/i2c_io.h
> 
> /usr/include/dev/i2c/i2cvar.h
> 
> /usr/include/dev/i2c/ihidev.h
> 
> So, I am stuck a bit... and have no idea what to do next...
> 
> Complete dmesg(8) below:
> 
> OpenBSD 7.0 (GENERIC.MP) #3: Wed Dec 15 13:14:20 MST 2021
>    [email protected]:/usr/src/sys/arch/arm64/compile/
> GENERIC.MP
> real mem  = 8426483712 (8036MB)
> avail mem = 8135118848 (7758MB)
> random: good seed from bootblocks
> mainbus0 at root: Raspberry Pi 4 Model B Rev 1.4
> psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
> cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
> cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu0: 1024KB 64b/line 16-way L2 cache
> cpu0: CRC32,ASID16
> cpu1 at mainbus0 mpidr 1: ARM Cortex-A72 r0p3
> cpu1: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu1: 1024KB 64b/line 16-way L2 cache
> cpu1: CRC32,ASID16
> cpu2 at mainbus0 mpidr 2: ARM Cortex-A72 r0p3
> cpu2: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu2: 1024KB 64b/line 16-way L2 cache
> cpu2: CRC32,ASID16
> cpu3 at mainbus0 mpidr 3: ARM Cortex-A72 r0p3
> cpu3: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu3: 1024KB 64b/line 16-way L2 cache
> cpu3: CRC32,ASID16
> efi0 at mainbus0: UEFI 2.7
> efi0: https://github.com/pftf/RPi4 rev 0x10000
> smbios0 at efi0: SMBIOS 3.3.0
> smbios0: vendor https://github.com/pftf/RPi4 version "UEFI Firmware v1.32"
> date 10/19/2021
> smbios0: Raspberry Pi Foundation Raspberry Pi 4 Model B
> apm0 at mainbus0
> "system" at mainbus0 not configured
> "axi" at mainbus0 not configured
> simplebus0 at mainbus0: "soc"
> bcmclock0 at simplebus0
> bcmmbox0 at simplebus0
> bcmgpio0 at simplebus0
> bcmaux0 at simplebus0
> ampintc0 at simplebus0 nirq 256, ncpu 4 ipi: 0, 1: "interrupt-controller"
> bcmtmon0 at simplebus0
> bcmdmac0 at simplebus0: DMA0 DMA2 DMA4 DMA5 DMA6 DMA7 DMA8 DMA9
> "timer" at simplebus0 not configured
> pluart0 at simplebus0
> com0 at simplebus0: ns16550, no working fifo
> "local_intc" at simplebus0 not configured
> bcmdog0 at simplebus0
> bcmirng0 at simplebus0
> "firmware" at simplebus0 not configured
> "power" at simplebus0 not configured
> "mailbox" at simplebus0 not configured
> sdhc0 at simplebus0
> sdhc0: SDHC 3.0, 250 MHz base clock
> sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed
> "gpiomem" at simplebus0 not configured
> "fb" at simplebus0 not configured
> "clocks" at mainbus0 not configured
> "phy" at mainbus0 not configured
> "clk-27M" at mainbus0 not configured
> "clk-108M" at mainbus0 not configured
> simplebus1 at mainbus0: "emmc2bus"
> sdhc1 at simplebus1
> sdhc1: SDHC 3.0, 100 MHz base clock
> sdmmc1 at sdhc1: 8-bit, sd high-speed, mmc high-speed, ddr52, dma
> "arm-pmu" at mainbus0 not configured
> agtimer0 at mainbus0: 54000 kHz
> simplebus2 at mainbus0: "scb"
> bcmpcie0 at simplebus2
> pci0 at bcmpcie0
> ppb0 at pci0 dev 0 function 0 "Broadcom BCM2711" rev 0x10
> pci1 at ppb0 bus 1
> xhci0 at pci1 dev 0 function 0 "VIA VL805 xHCI" rev 0x01: intx, xHCI 1.0
> usb0 at xhci0: USB revision 3.0
> uhub0 at usb0 configuration 1 interface 0 "VIA xHCI root hub" rev 3.00/1.00
> addr 1
> bse0 at simplebus2: address dc:a6:32:d3:42:c1
> brgphy0 at bse0 phy 1: BCM54210E 10/100/1000baseT PHY, rev. 2
> "dma" at simplebus2 not configured
> "hevc-decoder" at simplebus2 not configured
> "rpivid-local-intc" at simplebus2 not configured
> "h264-decoder" at simplebus2 not configured
> "vp9-decoder" at simplebus2 not configured
> "leds" at mainbus0 not configured
> "sd_io_1v8_reg" at mainbus0 not configured
> "sd_vcc_reg" at mainbus0 not configured
> "fixedregulator_3v3" at mainbus0 not configured
> "fixedregulator_5v0" at mainbus0 not configured
> simplebus3 at mainbus0: "v3dbus"
> "bootloader" at mainbus0 not configured
> simplefb0 at mainbus0: 800x600, 32bpp
> wsdisplay0 at simplefb0 mux 1: console (std, vt100 emulation)
> wsdisplay0: screen 1-5 added (std, vt100 emulation)
> dt: 445 probes
> scsibus0 at sdmmc1: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SR128, 0080> removable
> sd0: 121942MB, 512 bytes/sector, 249737216 sectors
> uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub" rev
> 2.10/4.21 addr 2
> bwfm0 at sdmmc0 function 1
> manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 2 not configured
> manufacturer 0x02d0, product 0xa9a6 at sdmmc0 function 3 not configured
> uhidev0 at uhub1 port 4 configuration 1 interface 0 "SINO WEALTH USB
> KEYBOARD" rev 1.10/1.00 addr 3
> uhidev0: iclass 3/1
> ukbd0 at uhidev0: 8 variable keys, 6 key codes
> wskbd0 at ukbd0: console keyboard, using wsdisplay0
> uhidev1 at uhub1 port 4 configuration 1 interface 1 "SINO WEALTH USB
> KEYBOARD" rev 1.10/1.00 addr 3
> uhidev1: iclass 3/0, 5 report ids
> uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
> ucc0 at uhidev1 reportid 3: 24 usages, 13 keys, enum
> wskbd1 at ucc0 mux 1
> wskbd1: connecting to wsdisplay0
> uhid1 at uhidev1 reportid 5: input=0, output=0, feature=5
> umass0 at uhub0 port 3 configuration 1 interface 0 "SupTronics X862" rev
> 3.00/0.20 addr 4
> umass0: using SCSI over Bulk-Only
> scsibus1 at umass0: 2 targets, initiator 0
> sd1 at scsibus1 targ 1 lun 0: <ASMT, 2115, 0> serial.174c0862202101000034
> sd1: 244198MB, 512 bytes/sector, 500118192 sectors
> vscsi0 at root
> scsibus2 at vscsi0: 256 targets
> softraid0 at root
> scsibus3 at softraid0: 256 targets
> root on sd1a (e58930ea2c9b3c87.a) swap on sd1b dump on sd1b
> WARNING: / was not properly unmounted
> gpio0 at bcmgpio0: 58 pins
> bwfm0:
> 
> P.S.
> I am new here, so any input about writing style, and correct usage of
> mailing lists are welcome!

Reply via email to