Hello!
Tovabbi fejlemenyek.
1. Ha a modem be van dugva, a gepbe, amikor elinditom, akkor
19d2:0031 usb-s azonositoval rendlekezik a kezdetektol fogva
:((
2. Ha bootolas utan kihuzom->bedugom, akkor
19d2:2000-re valtozik.
Ezutan hasznalva az usb_modeswitch-et, sem 2002-re sem 0031-re nem valt at
semmire.
:((
Illetve egy kis ido utan megis 0031 lesz.
De ekkor sem jelennek meg a ttyUSBx portok.
3. Ha 0031 allapotban van, (akar 1 vagy 2 miatt), akkor a
modprobe usbserial vendor=0x19d2 product=0x0031
parancsot kiadva, megjelennek az USB1,USB2,USB3 portok, a gammu-detect meg is
talalja oket, de nem mukodnek.
4. Az eszkozt kiprobaltam windows alol is, mukodik, lehet SMS-t kuldeni, tehat
jo a modem.
5. Nincs PIN kod.
6. A mukodo RPi-n levo gammu es usb_modeswitch beallitasokat atmasoltam.
Az usb_modeswitch futtatasa ezt adja:
Read config file: /etc/usb_modeswitch.conf
* usb_modeswitch: handle USB devices with multiple modes
* Version 2.5.1 (C) Josua Dietze 2017
* Based on libusb1/libusbx
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x19d2
DefaultProduct= 0x2000
TargetVendor= 0x19d2
TargetProduct= 0x0016
MessageContent="5553424312345678000000000000061e000000000000000000000000000000"
MessageContent2="5553424312345679000000000000061b000000020000000000000000000000"
Look for target devices ...
found USB ID 1d6b:0001
found USB ID 19d2:2000
vendor ID matched
found USB ID 1d6b:0002
found USB ID 1d6b:0001
found USB ID 1d6b:0002
found USB ID 1d6b:0001
found USB ID 1d6b:0002
found USB ID 1d6b:0001
found USB ID 1d6b:0002
found USB ID 1d6b:0002
No devices in target mode or class found
Look for default devices ...
found USB ID 1d6b:0001
found USB ID 19d2:2000
vendor ID matched
product ID matched
found USB ID 1d6b:0002
found USB ID 1d6b:0001
found USB ID 1d6b:0002
found USB ID 1d6b:0001
found USB ID 1d6b:0002
found USB ID 1d6b:0001
found USB ID 1d6b:0002
found USB ID 1d6b:0002
Found devices in default mode (1)
Access device 002 on bus 005
Get the current device configuration ...
Current configuration number is 1
Use interface number 0
with class 8
Use endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification)
-------------------------
Manufacturer: ZTE,Incorporated
Product: ZTE WCDMA Technologies MSM
Serial No.: P671A2PAND010000
-------------------------
Looking for active drivers ...
Set up interface 0
Use endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Read the response to message 1 (CSW) ...
Response successfully read (13 bytes), status 0
Reset response endpoint 0x81
Reset message endpoint 0x01
-> Run lsusb to note any changes. Bye!
Latszolag minden ok, de az lsusb szerint nem valtott at, maradt a 2000-es.
usb_modeswitch elott:
Bus 005 Device 002: ID 19d2:2000 ZTE WCDMA Technologies MSM
MF627/MF628/MF628+/MF636+ HSDPA/HSUPA
usb_modeswitch utan:
Bus 005 Device 002: ID 19d2:2000 ZTE WCDMA Technologies MSM
MF627/MF628/MF628+/MF636+ HSDPA/HSUPA
Egyenlore ugy nez ki felre kell raknom...
--
Udv:
Molnar Peter
http://www.petersoft.hu
---
Az e-mailen az AVG vírusellenőrzést végzett.
http://www.avg.com
_______________________________________________
Techinfo mailing list
[email protected]
Fel- és leiratkozás: http://lista.sulinet.hu/mailman/listinfo/techinfo
Illemtan: http://www.szag.hu/illemtan.html
Ügyfélszolgálat FAQ: http://sulinet.niif.hu/
