Good Luck,
Joe (Joe's Electric)....Jasper, Texas
Joe Tech2004 wrote:
PVR4660VK Projection TV. The AC 4 amp fuse blew up. I removed the
high circuit board to repair a cold solder of a voltage regulator
(9520). I did some dust cleaning inside the TV box and replace the
circuit board back then powered up. TV started put some how some
thing happened. The picture having three layers and if a text is
displayed it is curved up. I try to readjust vertical and horizontal
pots, put it did not help. I degaussed the TV set, it did not help. I
ran the convergence setup using remote control; I noticed it is
completely off. Blue, Green and Red are not aligned and off by few
degrees from vertical and horizontal. I try using remote control to
readjust red and blue but it did not even moved. I try to get them in
place by moving the magnets ring around the CRT. I was able to align
red and green or blue and green, but not able to align three of them. ================================= Check for 1 ohm resistors on 9-1690 board for open. R4162, R4163,
R1460 and R4161. If okay change R3243 (110kohm) on the 9-1674
module. This resistor is hard to find. Mounted beneath R3204 near
corner of daughter board ================================= ================================= P101702-4: Zenith PVR4660VK projection TV, convergence and pincushion
have jumped seriously out. Pincushion displacement at bottom edge of
screen is about 3 inches.
================================= Look for bad stk's on convergence module. This may take care of
pincushion too ================================= [EMAIL PROTECTED] From: [EMAIL PROTECTED](LeRoy Westlund)
Date: Tue, Apr 20, 2004, 9:54pm (EDT-2) To: [EMAIL PROTECTED]
Subject: [Techs] Zenith PVR4660VK Pix is bowed equally on top, bottom,
and sides, and convergence is bad. Reply to: [EMAIL PROTECTED]
(ELECTRONICS PROFESSIONALS LIST) ================================= Hi members, I repaired my focus problems by replacing the Focus block. I still have
bad convergence, and the pix is bowed equally on top, bottom, and both
sides. Does anybody have a fix listed for this problem ? I don't want to
buy convergence amps, cause I'm pretty sure it won't fix the problem. I'll buy some if you guys think I need them. Can't afford to waste money
buying parts that won't help. So far,..so good,...but,..I need a quick
fix,...bad ! Any help is appreciated,
LLW LeRoy Westlund
Westlund TV & Electronics 97 North Main "Where there's a will,...
Centerfield, UT 84622-0087 There's always a way."
Ph./Fax 435-528-3822 mailto:[EMAIL PROTECTED] ______________________________________________ Tech Repair CD...order your just $49.00 plus shipping...One year of
updates free. www.intrepid-video.com www.tech-repair.net Techs mailing list
[EMAIL PROTECTED] http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
Joes....Electronics
(Joe:Tech/2004)
[EMAIL PROTECTED]
Fax::509-479-2283
_______________________________________________ Tech Repair CD...order your just $49.00 plus shipping...One year of updates free. www.intrepid-video.com www.tech-repair.net Techs mailing list [EMAIL PROTECTED] http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
-- Joe Dickerson Joe's TV & Appliance Rt 1 Box 3781 Jasper, Texas 75951 (409) 384-3325 use same no. for fax
_______________________________________________ Tech Repair CD...order your just $49.00 plus shipping...One year of updates free. www.intrepid-video.com www.tech-repair.net Techs mailing list [EMAIL PROTECTED] http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
