Anton, tested again. after closed the folder , again opened drive and folder then ensured that charmap.txt is restored to original format and clicked on exe file - then only displayed encounter.exe message displayed. I also installed using setup.exe - works fine - for time being without any error message. with regards, -sriranga(79yrs)
On Wed, May 2, 2012 at 12:59 PM, Anton Zorin <[email protected]>wrote: > Perhaps it is a bug. Can you please be more specific? Did this message > appear after you clicked 'generate image' button again (after successfull > generation)? > > Regards, > > Anton Zorin > > > On Wed, May 2, 2012 at 11:24 AM, Sriranga(78yrsold) < > [email protected]> wrote: > >> Anton, >> Yes I agree with your point. I had mapped to replace t with te and t >> with xt so that two boxes should be created as [te] and [xt] In other >> words as per sample a=bc shown in the charmap.txt means "bc" should be >> replace with "a" >> Suddenly encounter message displayed when tried to run again. >> Where I made mistake. >> With regards, >> -siranga(79yrs) >> >> >> On Wed, May 2, 2012 at 12:34 PM, Anton Zorin >> <[email protected]>wrote: >> >>> Sriranga, >>> >>> te and xt are replaced correspondingly by t and x in the box file. So in >>> this case (with char mapping active) you will have just two entries in the >>> box file. >>> >>> Regards, >>> >>> Anton Zorin >>> >>> >>> On Wed, May 2, 2012 at 10:59 AM, Sriranga(78yrsold) < >>> [email protected]> wrote: >>> >>>> Anton, >>>> with reference to charmap.txt it is observed that box file did not >>>> have modified chars. >>>> *example* " text" t=*te* x=*xt * whereas in the box file shown only *t >>>> and x *- instead of te and xt. >>>> Where I made mistake? >>>> with regards, >>>> -sriranga(79yrs) >>>> >>>> >>>> On Wed, May 2, 2012 at 11:26 AM, Anton Zorin <[email protected] >>>> > wrote: >>>> >>>>> Hi, >>>>> >>>>> >>>>> I have added a new feature - mapping of multiple characters to a >>>>> signle one (using config file). There will be a single entry in the >>>>> box file for these combinations. >>>>> >>>>> Thanks. >>>>> >>>>> On Apr 5, 10:13 pm, Anton Zorin <[email protected]> wrote: >>>>> > Hi All, >>>>> > >>>>> > I think this tool could be useful for some of you. It allows to >>>>> > generate training images along with box files using the text edit >>>>> > control's contens as input. So simple formatting is possible, font >>>>> > antialiasing can be turned on/off). Currently compiled only for >>>>> > windows (installer is available on the downloads page). Any comments/ >>>>> > remarks/bugs are welcome. >>>>> > >>>>> > Thanks in advance. >>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "tesseract-ocr" group. >>>>> To post to this group, send email to [email protected] >>>>> To unsubscribe from this group, send email to >>>>> [email protected] >>>>> For more options, visit this group at >>>>> http://groups.google.com/group/tesseract-ocr?hl=en >>>>> >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "tesseract-ocr" group. >>>> To post to this group, send email to [email protected] >>>> To unsubscribe from this group, send email to >>>> [email protected] >>>> For more options, visit this group at >>>> http://groups.google.com/group/tesseract-ocr?hl=en >>>> >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "tesseract-ocr" group. >>> To post to this group, send email to [email protected] >>> To unsubscribe from this group, send email to >>> [email protected] >>> For more options, visit this group at >>> http://groups.google.com/group/tesseract-ocr?hl=en >>> >> >> -- >> You received this message because you are subscribed to the Google >> Groups "tesseract-ocr" group. >> To post to this group, send email to [email protected] >> To unsubscribe from this group, send email to >> [email protected] >> For more options, visit this group at >> http://groups.google.com/group/tesseract-ocr?hl=en >> > > -- > You received this message because you are subscribed to the Google > Groups "tesseract-ocr" group. > To post to this group, send email to [email protected] > To unsubscribe from this group, send email to > [email protected] > For more options, visit this group at > http://groups.google.com/group/tesseract-ocr?hl=en > -- You received this message because you are subscribed to the Google Groups "tesseract-ocr" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/tesseract-ocr?hl=en
