In message <c99a56f5.7dd8%[email protected]> "Mallette, Edwin" writes: > > I concur with the points made by Nurit and Ben. In addition there is > the asymmetric delay problems (for a given link) that lots of work has > gone into to solve with 1588 - 1588 Transparent Clock / 1588 residency > time compensation. To the best of my knowledge this is not being > addressed for NTP. > > Thus +1 for the default of IEEE1588. > > Ed
NTP has always, probably from day one but at least going back to the early 1990s (AFAIK), compensated for asymetric delay. With hardware assist, NTP deployed over a link is every bit as accurate as PTP deployed over a link with hardware assist. It is probably more accurate due to the jitter compensation used by NTP and omited by PTP. Some hardware doesn't quite get all the jitter out. Admitedly, NTP is more complex due to the compensation that is included in NTP and not in PTP. OTOH if there is something that favors PTP, then we should approach the TICTOC WG and pass along that requirements. For example, a two step transmit, allowing the transmit timestamp on a given packet to be sent with the next packet, may simplify hardware. If so, we ask TICTOC to support that in NTP. I support making the default NTP. This is the IETF and given a very nearly equivalent IETF solution and an IEEE solution we should require the IETF solution, make the IEEE solution optional, and if there are any shortcomings to the IETF solution, address that in the appropriate IETF WG. Curtis > From: "Sprecher, Nurit (NSN - IL/Hod HaSharon)" > <[email protected]<mailto:[email protected]>> > Date: Fri, 4 Mar 2011 05:32:07 -0500 > To: "[email protected]<mailto:[email protected]>" > <[email protected]<mailto:[email protected]>>, > "[email protected]<mailto:[email protected]>" > <[email protected]<mailto:[email protected]>> > Cc: "Zhao, Peng (NSN - CN/Shanghai)" > <[email protected]<mailto:[email protected]>>, "Pietilainen, > Antti (NSN - FI/Espoo)" > <[email protected]<mailto:[email protected]>>, > "[email protected]<mailto:[email protected]>" > <[email protected]<mailto:[email protected]>> > Subject: Re: [mpls] draft-ietf-mpls-loss-delay Timestamp > > Stewart hi, > The accuracy targets as described below are approaching a level where > on-path support is needed. > In this case the clear choice is IEEE 1588 because it specifies > on-path support whereas NTP does not. > Even without on-path support IEEE 1588 could be better if better > accuracy is pursued by sending multiple timing packets per second per > slave/client, because standard NTP clients send messages at a very low > rate for saving server resources. > I support the default of IEEE1588! > Best regards, > Nurit > > From: [email protected]<mailto:[email protected]> [mailto:[email protected]] On Behalf Of ext Stewart Bryant > Sent: Thursday, March 03, 2011 6:07 PM > To: [email protected]<mailto:[email protected]> > Cc: [email protected]<mailto:[email protected]> > Subject: [mpls] draft-ietf-mpls-loss-delay Timestamp > > > We have received a LC comment on draft-ietf-mpls-loss-delay concerning > the default timestamp. > > In the first version of the draft we proposed NTP, but following > initial comments from the MPLS-TP community we changed to > IEEE1588. This requirement for IEEE1588 can be traced back to the > choice of using IEEE1588 in Y.1731. > > We have now received a LC request to change the default back to NTP. > > NTP is the "natural" choice for an IETF protocol. NTP is specified in > IETF and is used in other MPLS protocols such as LSP ping. It is > implemented on almost every host and every router. However in general > the implementations provides a relatively low precision timestamp, and > the NTP time distribution infrastructure operates on a best effort > basis. Thus even a good client implementation would normally have a > relatively low quality path to the server, which would result in a low > quality of timestamp. NTP could be made to work to higher accuracy, > but defacto upgrading NTP and providing high quality NTP paths to the > time servers is not getting much attention. Computing timestamp > differences is easier with NTP. > > On the other hand IEEE1588 has defacto become the two way time tranfer > protocol for precision applications. IEEE1588 only provides high > quality time in well engineered networks with some form of hop by hop > assistance. It is not widely implemented other than in equipment > targeted to specific markets, although one of those markets is in > mobile backhaul applications where we expect to see significant > initial deployment of MPLS-TP. Computing timestamp differences is > harder with IEEE1588 > > The loss-delay work is targeting to be able to do one way packet delay > measurement, so it does need a higher quality of timestamp than is > required in general purpose network instrumentation. > > Converting from IEEE1588 to NTP is not trivial, since they use > different epochs, and different representations of sub-second time. In > a "traditional" NTP implementation the time error due to on the fly > conversion is likely to be small compared to the time error in the > time synchronization system, but an IEEE1588 system would need > hardware conversion to maintain the accuracy for an NTP timestamp. > > So the question arises, should we make IEEE1588 or NTP the default for > draft-ietf-mpls-loss-delay. Much as I would like to suggest that we > should go back to NTP for consistency with other IETF protocols, I > have difficulty reconciling this with the situation in network > deployments and thus suggest that we continue to use IEEE1588. > > What is the opinion of the working group? > > Stewart (speaking as a draft editor) _______________________________________________ TICTOC mailing list [email protected] https://www.ietf.org/mailman/listinfo/tictoc
