The status shown looks mostly ok. Reference is GPS, plenty of satellites tracked, signal levels ok, etc. Your antenna alarm is due to the 0ma current - should not be a problem. But… your XDOP values are all 0 which seems suspicious and the status is still ‘OCXO Warmup’ (not 100% on that since I don’t have a Trimble unit, only Samsung and Symmetricom). I would suggest that you eliminate the splitter and connect directly to your antenna, just to eliminate things. Also, the OCXO could be substantially off frequency. If possible, I’d measure the EFC voltage and frequency. The output from DIAGnostic:LOG:READ:ALL? would also be useful.
You also might want to post to EEVBlog as there is a substantial thread on these UCCM units there at https://www.eevblog.com/forum/projects/a-look-at-my-symmetricom-gpsdo-(ocxo-furuno-receiver)/ > On Jul 27, 2021, at 2:54 PM, ordnit via time-nuts <[email protected]> > wrote: > > Hi there, > thank you for valuable information I get everyday from the list. > > After a very long time I managed to power up a Trimble GPSDO, connected > to an aexternal antenna. > > UCCM >*IDN? > TRIMBLE,57964-15,86854165,V3.0.0.11-01 > Datecode: 0814 (pretty old, but still in its teen years) > > Some output from "common commands": > > UCCM >SYSTem:STATus? > > ------------------------------------------------------------------------------- > 57964-15 serial number 86854165 firmware ver 3.0.0.11-01LINK mode > ------------------------------------------------------------------------------- > Reference Status __________________________ Reference Outputs > _______________ > XX Ref 8KHz 0: [LOS] > XX Ref 8KHz 1: [LOS] TFOM 4 FFOM > 1 > XX Ref 8KHz 2: [LOS] UCCM A Status[OCXO WARMUP] > XX Ref 8KHz 3: [LOS] > >> GPS: [phase:-3.3E-05, settling] > ACQUISITION ...................................................[GPS 1PPS > Valid] > Tracking: 8 ____ Not Tracking: 3 ________ Time > ____________________________ > PRN El Az C/N PRN El Az GPS 11:44:34 27 Jul > 2021 > 32 39 107 46 3 10 226 > 1 28 284 37 16 6 189 ANT DLY 0 ns > 10 40 51 42 14 8 327 Position ________________________ > 8 79 239 45 MODE Hold > 23 7 49 38 > 21 52 297 43 LAT N 43:35:11.819 > 27 55 153 43 LON E 13:31:1.250 > 22 32 230 41 HGT +225.27 m (MSL) > > > ELEV MASK 5 deg > ------------------------------------------------------------------------------- > > UCCM >POSSTATus > > --------------------------------------------- > 07/27/2021 11:44:57 > --------------------------------------------- > Position: LAT(N 43:35:11.819) LON(E 13:31:1.250) H( +225.27 m MSL) > --------------------------------------------- > Geometry: PDOP(0.0) HDOP(0.0) VDOP(0.0) > num of visible sats > 10 > num of sats tracked > 10 > -------- Receiver Channel State -------- > CH 0 > SateID(03) TrackMode(pos avail) SigValue(36) > CH 1 > SateID(32) TrackMode(pos avail) SigValue(47) > CH 2 > SateID(01) TrackMode(pos avail) SigValue(37) > CH 3 > SateID(16) TrackMode(pos avail) SigValue(34) > CH 4 > SateID(10) TrackMode(pos avail) SigValue(42) > CH 5 > SateID(08) TrackMode(pos avail) SigValue(44) > CH 6 > SateID(14) TrackMode(tracking ) SigValue(20) > CH 7 > SateID(23) TrackMode(pos avail) SigValue(37) > CH 8 > SateID(21) TrackMode(pos avail) SigValue(44) > CH 9 > SateID(27) TrackMode(pos avail) SigValue(43) > CH 10 > SateID(22) TrackMode(pos avail) SigValue(40) > CH 11 > SateID(00) TrackMode(tracking ) SigValue( 0) > --------------------------------------------- > Rcvr Status(1): > --------------------------------------------- > Antenna Voltage: 5000.00mV , Antenna Current: 0.00mA > > UCCM >status > > - UCCM Slot STATE- > > 1-1. #Now ACTIVE STATUS ---------------- [OCXO Warm] > 1-2. #Before ACTIVE STATUS ------------- [Alarm] > 2-1. #Reference Clock Operation -------- [Not Used] > 2-2. #Current Reference Type ----------- [GPS] > 2-3. #Current Select Reference --------- [GPS 1PPS] > 2-4. #Current Reference Status --------- [Good Accuracy & Stable] > #GPS STATUS ----------------------- [Available] > #Priority Level ------------------- [LINK > GPS] > #ALARM STATUS > #H/W FAIL [ LINK ] > #OPERATION ALARM ------------------ [Antenna] > 3-1. #PLL STATUS ----------------------- [DISABLE] > 3-2. #Current PLL MODE ----------------- [OFFSET OBSERVATION MODE] > > > The issue I'm facing is following: even after a long uptime, I never com to a > "fast blinking led" and PLL status "enabled". Monitoring device with LHv6, > shows an "operation mode" alternating Locked (few seconds" and "recvery". > TFOM is quite always 3 or 4. Power supply is linear, with output voltage 5.6V > or 6V. I made many tests but had no luck. > > Sys:stat showa a "phase" value moving from -1.4E-05,settling up to > -4.3E-06, settling. On an old post I read that it might be caused by the > oscillator drifting due to age. > > Any guess? Do I have to throw the unit from the window? For your reference, I > have a samsung unit connected to same antenna via a splitter. The GPSDO is > performing very well. > > Thank you in advance for help. > Best regards. > _______________________________________________ > time-nuts mailing list -- [email protected] -- To unsubscribe send an > email to [email protected] > To unsubscribe, go to and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] -- To unsubscribe send an email to [email protected] To unsubscribe, go to and follow the instructions there.
