My mistake, I did receive the output.
I'll take a look now.

Please excuse my brevity. Sent from my iPhone.

On 28/11/2012, at 15:23, Matthew Tolle <[email protected]> wrote:

> 
> Hi Mike,
> 
> Thanks for responding.
> 
> Debug 5 output attached. I changed the remote IP address to 5.5.5.5 for 
> privacy. 
> 
> <tinc>
> 
> Tinc on the remote side has always been set to switch mode. I've tried it in 
> many different forms on the laptop side. It's currently set to hub mode. 
> I can rerun the debug for you in switch mode if you need that. From what I 
> read it should be the same. 
> 
> I've tried setting the IP by hand with no luck. Can't ping the other side(the 
> remote server or the gateway). 
> 
> I don't run or have access to the DHCP server on the remote side, but I'm 
> fairly sure it has not changed. The laptop gets it's IP address just fine 
> when it's local to the site. 
> 
> Running the exact same config linux(client) to linux(remote) it works just 
> fine getting it's address. I tried changing the MAC address on my laptop to 
> the MAC of the linux box to see if there was some oddball MAC filtering going 
> on. No help I still can't get an address. 
> 
> my tinc.conf file reads: 
> 
> Name = laptop
> Mode = hub
> Device = /dev/tap0
> 
> The host file for laptop has nothing but it's key in it. 
> 
> The remote server does the connecting. It's behind a firewall. 
> 
> The remote server's tinc.conf file:
> 
> Name = remote
> ConnectTo = late
> ConnectTo = laptop
> ConnectTo = cranky
> Mode = switch
> 
> servers hosts file: 
> 
> Subnet = 5.5.5.0/23
> Address = 5.5.5.5
> 
> -----BEGIN RSA PUBLIC KEY-----
> 
> What other info can I provide? 
> 
> Thank you for looking at this.
> 
> -Matt
> 
> 
> On Nov 27, 2012, at 7:02 PM, Mike Bentzen <[email protected]> wrote:
> 
>> Can you please provide tinc debug 5 output?
>> 
>> Tinc should be set to switch mode.
>> 
>> If you manually set an IP address, can you ping all the hosts on the tinc 
>> network?
>> 
>> Have you restarted or upgraded your dhcp server? 
>> 
>> Mike
>> 
>> Please excuse my brevity. Sent from my iPhone.
>> 
>> On 28/11/2012, at 11:09, Matthew Tolle <[email protected]> wrote:
>> 
>>> 
>>> Hi folks,
>>> 
>>> A while ago I setup my macbook pro to run TINC to my linux box. It's worked 
>>> just swell since April. The other day it just stopped working. The 
>>> connection comes up and everything seems fine but I can't DHCP a correct 
>>> address. 
>>> 
>>> I followed the old setup instructions that were located here: 
>>> http://www.tinc-vpn.org/examples/macbook-install/ They seem to be gone now.
>>> 
>>> When I try and DCHP an address now all I get is the 169.254.219.* address 
>>> that is OSX's confusing way of telling you that you didn't get a real 
>>> address. 
>>> 
>>> I've poked around at everything I can think of and can't figure it out. 
>>> Running linux box to linux box works just fine and DHCPs an address just 
>>> fine. 
>>> 
>>> I upgraded to the latest version of TINC. I've tried swaping my Mac tinc 
>>> config to switch, hub, and none with no change. 
>>> 
>>> I've tried connecting and being connected to the main linux box. 
>>> 
>>> I've tried going over the TCP dump with no luck.
>>> 
>>> Has anyone seen this before? Any resolution? 
>>> 
>>> Thanks for taking the time to read this and for any suggestions. 
>>> 
>>> -Matt
>>> 
>>> 
>>> _______________________________________________
>>> tinc mailing list
>>> [email protected]
>>> http://www.tinc-vpn.org/cgi-bin/mailman/listinfo/tinc
>> _______________________________________________
>> tinc mailing list
>> [email protected]
>> http://www.tinc-vpn.org/cgi-bin/mailman/listinfo/tinc
> 
> _______________________________________________
> tinc mailing list
> [email protected]
> http://www.tinc-vpn.org/cgi-bin/mailman/listinfo/tinc
_______________________________________________
tinc mailing list
[email protected]
http://www.tinc-vpn.org/cgi-bin/mailman/listinfo/tinc

Reply via email to