I reinstalled everything from scratch today, installed first 1.1.0 and then
upgraded to 1.1.11 and it failed. I then upgraded to 1.1.15cvs snapshot
from December, but it still fails. I notice now that I cannot interrupt the
transfer where it's stuck and it isn't doing the receive infinite loop anymore,
it is just sitting blank after two transmits, as in the email below.
On 1/5/06, Sam Pierson <[EMAIL PROTECTED]> wrote:
> Specifically,
>
> $ uisp -dprog=mib510 -dserial=com1 --wr_fuse_h=0xd8 -dpart=ATmega128
> --wr_fuse_e=ff --erase --upload if=build/micaz/main.srec.out -v=4
> Transmit: { . [aa] U [55] U [55] . [aa] . [17] Q [51] 1 [31] . [13] . [01] }
> Transmit: { . [aa] U [55] U [55] . [aa] . [17] Q [51] 1 [31] . [13] . [01] }
> Receive: { }
> Receive: { }
> Receive: { }
> Receive: { }
> Receive: { }
> ...
>
> On 1/5/06, Sam Pierson <[EMAIL PROTECTED]> wrote:
> > It appears as though mine is stuck in the same Receive loop.
> >
> > On 1/5/06, Hannes Geissbuehler <[EMAIL PROTECTED]> wrote:
> > > I have exaclty the same problem..
> > >
> > > till last week it worked and now it dies during trying to uplad the file.
> > >
> > > Could It be that a new Windows Bugfix somehow prevents some commands to
> > > the com port ?
> > >
> > > running the uisp in debug mode shows that it ends in an endless loop
> > > of
> > >
> > > Receive: { } commands..
> > >
> > > any Ideas ?
> > >
> > > Hannes
> > > > I've been sort of stuck on this after trying a lot of different things.
> > > >
> > > > I have an MIB510 board and a few micaz motes. I connect the
> > > > board to this laptop through the serial port. I've successfully
> > > > uploaded binaries to mica2's in the past.
> > > >
> > > > Now I've tried on tinyos 1.1.10, 1.1.11, and the latest 1.1.15 cvs
> > > > snapshot. The problem still occurs:
> > > >
> > > > If I try to upload the Blink app, for example, I do this:
> > > >
> > > > make micaz install mib510,com1
> > > >
> > > > It compiles the binary and then executes this command to upload:
> > > >
> > > > uisp -dprog=mib510 -dserial=com1 --wr_fuse_h=0xd8 -dpart=ATmega128
> > > > --wr_fuse_e=ff --erase --upload if=build/micaz/main.srec.out
> > > >
> > > > But it just sits here during this command and nothing happens.
> > > >
> > > > Any ideas would be appreciated.
> > > >
> > > > _______________________________________________
> > > > Tinyos-help mailing list
> > > > [email protected]
> > > > https://mail.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
> > > >
> > >
> > >
> > >
> >
> >
> > --
> > Sam Pierson
> >
>
>
> --
> Sam Pierson
>
--
Sam Pierson
_______________________________________________
Tinyos-help mailing list
[email protected]
https://mail.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
