Problem solved. According to http://sensorweb.vancouver.wsu.edu/wiki/index.php/Tinyos,
You cannot use mib520 in the command, or it will show flash error again and again... The reason is that MIB520 is not registed under Tinyos, but MIB510 dose. So using a command line like: $ make micaz install mib510,/dev/ttyUSB0 instead of with mib520, made sure everything went fine, regardless of using mib510 or mib520. Thanks everyone for the help! On 4/2/07, Tony Mancill <[EMAIL PROTECTED]> wrote:
Hi Pedro, I use MIB520 boards with Linux and had all kinds of weird problems during programming until I realized that there were usbserial errors in dmesg about communicating with the FTDI chip. The solution for my system was the remove the ehci_hcd module, which was being automatically loaded by the kernel. tony Pedro Almeida wrote: > > Hello all! > > With the help of all and the fantastic tutorial by Miguel Silva ( > http://www.mail-archive.com/[email protected]/msg09493.html > < http://www.mail-archive.com/[email protected]/msg09493.html>), i was able to install everything right on FC6 (or so i believe). > > Right now was was doing the basic programming for the Blink application, > and i came up with an error for which i have found plenty of complains, > but short on solutions (mainly because it's mostly related to TinyOS1.x > and mib510 boards). > > So I do, as supposed > > $make micaz install mib520,/dev/ttyUSB1 > > gives me this: > > [EMAIL PROTECTED] Blink]# make micaz install mib520,/dev/ttyUSB1 > mkdir -p build/micaz > compiling BlinkAppC to a micaz binary > ncc -o build/micaz/main.exe -Os -finline-limit=100000 -Wall -Wshadow > -Wnesc-all -target=micaz -fnesc-cfile=b > uild/micaz/app.c -board=micasb -fnesc-dump=wiring > -fnesc-dump='interfaces(!abstract())' -fnesc-dump='refere > nced(interfacedefs, components)' > -fnesc-dumpfile=build/micaz/wiring-check.xml BlinkAppC.nc -lm > compiled BlinkAppC to build/micaz/main.exe > 2410 bytes in ROM > 51 bytes in RAM > avr-objcopy --output-target=srec build/micaz/main.exe build/micaz/main.srec > avr-objcopy --output-target=ihex build/micaz/main.exe build/micaz/main.ihex > writing TOS image > cp build/micaz/main.srec build/micaz/main.srec.out > installing micaz binary with dapa > uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff --erase > pulse > Atmel AVR ATmega128 is found. > Erasing device ... > pulse > Reinitializing device > Atmel AVR ATmega128 is found. > > Fuse High Byte set to 0xd9 > > Fuse Extended Byte set to 0xff > sleep 1 > uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff > --upload if=build/micaz/main.srec.out > pulse > Atmel AVR ATmega128 is found. > Uploading: flash > > Fuse High Byte set to 0xd9 > > Fuse Extended Byte set to 0xff > sleep 1 > uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff > --verify if=build/micaz/main.srec.out > pulse > Atmel AVR ATmega128 is found. > Verifying: flash > flash error at address 0x0: file=0x0c, mem=0x00 > flash error at address 0x1: file=0x94, mem=0x00 > flash error at address 0x2: file=0x49, mem=0x00 > flash error at address 0x4: file=0x0c, mem=0x00 > .... > flash error at address 0x968: file=0x18, mem=0x00 > flash error at address 0x969: file=0x95, mem=0x00 > > Fuse High Byte set to 0xd9 > > Fuse Extended Byte set to 0xff > rm -f build/micaz/main.exe.out build/micaz/main.srec.out > > > one of the solutions proposed doing, to clean the memory or something : > $uisp -dprog=dapa --erase, that gave > > pulse > Probably the AVR MCU is not in the RESET state. > Check it out and run me again. > > i have no idea what this means. > i have also tried using mib510 instead of mib520, keeping the /ttyUSB1, > but didnt work either. > > please, any solutions? > > thanks once more! > > > ------------------------------------------------------------------------ > > _______________________________________________ > Tinyos-help mailing list > [email protected] > https://mail.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
_______________________________________________ Tinyos-help mailing list [email protected] https://mail.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
