I forgot an important (in my opinion) detail:
at the mica side, I would like recevie packet send by serial port (UART)
using these followuing statements:
event message_t *UartReceive.receive[am_id_t id](message_t *msg, void
*payload, uint8_t len) {...}
Help me, please
2007/9/27, Roberto Gioè <[EMAIL PROTECTED]>:
>
> Hi,
> yes I'm italian.
> I'm still looking for a solution to my problem: send data from a pc (or a
> stargate) to a mote using the serial port.
> I hope someone help me to found a solution very soon
> good luck
>
> RG
>
> 2007/9/27, Leonardo <[EMAIL PROTECTED]>:
> >
> > Ciao sei Italiano?? se si mi daresti delle guide per mandare pacchetti
> > tramite serial? io devo fare un programma in C# e devo madare dati al
> > sensore...
> >
> > If you are not italian :D
> > Can you send me tutorial, guidelines or any documents to create and a
> > packet for send it by serial?
> > thanks
> > Leonardo
> >
> > Roberto Gioè ha scritto:
> >
> > Hi all.
> > I would like create a packet to send to a micaz by a serial port.
> > The creation ot the packet must be done in a pc using an application
> > written in C.
> > I use TinyOs-2.x
> > I create the packet with the following statements:
> > ----------
> > char output_buffer[TOS_PACKET_LENGTH]; //TOS_PACKET_LENGTH=41
> >
> > //output_buffer is initialized to zero
> > void create_packet() {
> >
> > /* Setup packet header information */
> > output_buffer[0] = 0x7e; //Frame
> > output_buffer[1] = 69; //SERIAL_PROTO_PACKET_NOACK
> > output_buffer[2] = 0x00; //Sequence number byte: SerialP
> > output_buffer[3] = 0xff; //Destination Address
> > output_buffer[4] = 0xff; //Destination Address
> > output_buffer[5] = 0x00; //Source Address
> > output_buffer[6] = 0x00; //Source Address
> > output_buffer[7] = 28; //Payload length
> > output_buffer[8] = 0; //Group ID
> > output_buffer[9] = 6; //AMType
> >
> > /* Payload */
> > output_buffer[10]='c';
> > output_buffer[11]='i';
> > output_buffer[12]='a';
> > output_buffer[13]='o';
> >
> > /* CRC bytes and end frame */
> > output_buffer[TOS_PACKET_LENGTH-3] = 200;
> > output_buffer[TOS_PACKET_LENGTH-2] = 197;
> > output_buffer[TOS_PACKET_LENGTH-1] = 0x7e;
> > --------------
> > When I send this packet to the micaz mote no leds fire!
> > Is the packet format correct? I read more times the guidelines to create
> > a packet and I read the Serial.h file too.
> > Thanks for your answer
> >
> > Roberto
> >
> >
> > ------------------------------
> >
> > _______________________________________________
> > Tinyos-help mailing list
> >
> > [email protected]
> > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
> >
> >
> >
>
--
Platform: Linux Fedora
TinyOS version: 2.x
Programmer: MIB510
Device(s): Micaz, Stargate
_______________________________________________
Tinyos-help mailing list
[email protected]
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
