If I understand correctly, your TOSBase mote is flashing LEDs when you try to send a message so that means that your baud rate and such are probably correct on the PC side. But your re-Mote is not receiving anything...
It's possible that SimpleCmd expects to get a message to a specific moteID, I'd have to go look through all the code... See if you can get it to accept a message with a BCAST address. Have you had these devices successfully using the radio at all? You might try something a little simpler like CntToRfm to see if you get any communication. And make sure you've compiled all the programs with the same radio channel defined. I don't know why adding TimerC to the TOSBase config is troublesome. I have done just that for mica2's to add some bit twiddling outputs to my base-station. What is the actual error message you get? But adding new radio code is probably a recipe for disaster since TOSBase uses a bunch of lower level functions to do it's magic, so I'd just leave it well enough alone. I think what you see in RadioSend is the initial byte send, subsequent bytes get sent from an interrupt routine somewhere else in the code there. MS Renee Azhen wrote: > thanks, Ashraf, I am using tinyos 1.x, in which the baud rate of telosb > is 57600, > thanks! > Sam > > */[EMAIL PROTECTED]/* 写道： > > HI > I don’t know but I remember that I saw something in lesson 4 mention > that is the baud rate for telosb is 115200 , you can check it. > http://www.tinyos.net/tinyos-2.x/doc/html/tutorial/lesson4.html > Ashraf > > ----- Original Message ----- > From: Renee Azhen > Date: Tuesday, December 25, 2007 11:00 pm > Subject: 回复： Re: [Tinyos-help]: SimpleCMD can't receive message > (anotherstrangephenonmenon) > > > and in TOSBaseM.nc, I went through the code in line 107 which is > > used to send TOS_MSG via radio, the code is: > > Result = call RadioSend.send(gpTxMsg); // TOS_MsgPtr gpTxMsg; > > > > and it is very interesting if you look through the > > implementation of RadioSend.send in CRCPacket.nc, the send > > function only send the first byte of gpTxMsg, oh, my god!!!!! > > I am really lost by this app. > > > > thanks > > Sam > > > > the code is like following: > > /* Command to transmit a packet */ > > command result_t Send.send(TOS_MsgPtr msg) { > > if (txCount == 0) > > { > > txCount = 1; > > txLength = TOS_MsgLength(msg->type); > > sendPtr = (uint8_t *)msg; > > /* send the first byte */ > > if (call ByteComm.txByte(sendPtr[0])) > > { > > post CRCCalc(); > > return SUCCESS; > > } > > else > > txCount = 0; > > } > > return FAIL; > > } > > > > Renee Azhen > > hi, ashrafalqudah > > thanks for your help:) > > I was always using [EMAIL PROTECTED]:57600, yet it doesn't work! > > > > if I upload the TOSBase into my node, the TOSBase works well, > > but if the SimpleCMD node can not receive message. > > I am so confuzed why I add GenericComm into the TOSBase.nc, > > then the TOSBase node can't work, and the "write failed" was > > displayed on the SF. > > > > thanks all the same! > > Sam > > > > > > [EMAIL PROTECTED] > > hi Sam > > I faced a problem like this but I was using micaz platform not > > the telosb, however i solved it in very simple and unexpected > > solution you can try this: > > when you want to specify the baud rate when running the > > serialforwarder write it as number not telosb. in micaz i used > > param = [EMAIL PROTECTED]:57600 rather than param = [EMAIL > PROTECTED]:micaz > > believe me its worked. > > Thanks for all > > > > ----- Original Message ----- > > From: Renee Azhen > > Date: Tuesday, December 25, 2007 7:46 pm > > Subject: [Tinyos-help]: SimpleCMD can't receive message (another > > strangephenonmenon) > > > And another strange phenomena. > > > If I add component TimerC into the TOSBase.nc, > > > for example: > > > I change the code from: > > > components Main, TOSBaseM, RadioCRCPacket as Comm, FramerM, > > > UART, LedsC; > > > To > > > components Main, TOSBaseM, RadioCRCPacket as Comm, FramerM, > > > UART, LedsC, TimerC; > > > and then, the TOSBase can't work either. > > > > > > Why?? Could you tell me? > > > thanks > > > Sam > > > > > > > > > > *********************************************************************************** > dear all: > > > Merry Christmas! > > > > > > I have two telosb nodes. > > > one is connected to a PC and programmed with TOSBase. > > > the other is programmed with SimpleCMD. > > > > > > when I run the BcastInject to send a message to the first > > > node, it works well(the Leds toggled), but the other node > > which > > > is programmed with SimpleCMD had no response. > > > > > > I have searched in the Mailing list, and found many people > > > posted the same question, but none gave a good answer. > > > > > > My nodes is telosb platform, could anyone tell me how to fix it? > > > > > > Thanks > > > Sam > > > > > > > > > --------------------------------- > > > ¨§ > > > > > > > > > > > > > --------------------------------- > > ê×¨× > > > > > > --------------------------------- > > ê×¨× > > > > > ------------------------------------------------------------------------ > 雅虎邮箱传递新年祝福，个性贺卡送亲朋！ > <http://cn.mail.yahoo.com/gc/index.html?entry=5&souce=mail_mailletter_tagline> > > > > > ------------------------------------------------------------------------ > > _______________________________________________ > Tinyos-help mailing list > [email protected] > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help -- Platform: WinXP/Cygwin TinyOS version: 1.x, Boomerang Programmer: MIB510 Device(s): Mica2, MicaZ, Tmote Sensor board: homebrew _______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
