Dear Michael, Thank you very, very, very much!! It works very well :) I did not have the Makelocal, so I had to created a Makelocal file on /opt/tinyos_2x/support/make to add your suggestions informations ... and my Blink app was perfectly uploaded ;)
Cheers Lea On Fri, Jun 27, 2008 at 1:35 PM, Michael Schippling <[EMAIL PROTECTED]> wrote: > You are using the wrong syntax to set the programmer options. > The "uisp -dprog=dapa ..." line indicates that it's trying to use > the old parallel connection programmer. I always forget how to do > it on the command line so I set this in my Makelocal file: > > DEFAULT_PROGRAM=mib510 > MIB510=COM5 > > where you might use /dev/ttyS0 > > MS > > > Underléa Cabreira Corrêa wrote: > >> Dear all, >> >> I 'm just getting start with TinyOS and Mica Motes platform, but I already >> have got a problem in the first lesson from tutorial. >> I m using TinyOS 2.x in a Linux Ubunto machine. I have followed the >> installation instruction from >> http://www.tinyos.net/tinyos-2.x/doc/html/install-tinyos.html. I have >> tested my environment with $ tos-check-env and I just have got a warning >> about the GraphViz version ... >> My problem is : I can t install the Blink app on Mica2. Every time I have >> tried I have got the following flash error address :( >> >> [EMAIL PROTECTED]:/opt/tinyos-2.x/apps/Blink# make mica2 install, 1 MIB510, >> /dev/ttyS0 >> mkdir -p build/mica2 >> compiling BlinkAppC to a mica2 binary >> ncc -o build/mica2/main.exe -Os -finline-limit=100000 -Wall -Wshadow >> -Wnesc-all -target=mica2 -fnesc-cfile=build/mica2/app.c -board=micasb >> -DIDENT_APPNAME=\"BlinkAppC\" -DIDENT_USERNAME=\"root\" >> -DIDENT_HOSTNAME=\"besouro\" -DIDENT_USERHASH=0xcc8c50dfL >> -DIDENT_TIMESTAMP=0x48641421L -DIDENT_UIDHASH=0x39bb344dL -fnesc-dump=wiring >> -fnesc-dump='interfaces(!abstract())' -fnesc-dump='referenced(interfacedefs, >> components)' -fnesc-dumpfile=build/mica2/wiring-check.xml BlinkAppC.nc -lm >> compiled BlinkAppC to build/mica2/main.exe >> 7130 bytes in ROM >> 52 bytes in RAM >> avr-objcopy --output-target=srec build/mica2/main.exe >> build/mica2/main.srec >> avr-objcopy --output-target=ihex build/mica2/main.exe >> build/mica2/main.ihex >> writing TOS image >> cp build/mica2/main.srec build/mica2/main.srec.out >> installing mica2 binary with dapa >> uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff --erase >> pulse >> Atmel AVR ATmega128 is found. >> Erasing device ... >> pulse >> Reinitializing device >> Atmel AVR ATmega128 is found. >> >> Fuse High Byte set to 0xd9 >> >> Fuse Extended Byte set to 0xff >> sleep 1 uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 >> --wr_fuse_e=ff --upload if=build/mica2/main.srec.out >> pulse >> Atmel AVR ATmega128 is found. >> Uploading: flash >> >> Fuse High Byte set to 0xd9 >> >> Fuse Extended Byte set to 0xff >> sleep 1 uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 >> --wr_fuse_e=ff --verify if=build/mica2/main.srec.out >> pulse >> Atmel AVR ATmega128 is found. >> Verifying: flash >> flash error at address 0x0: file=0x0c, mem=0xff >> flash error at address 0x1: file=0x94, mem=0xff >> ... >> flash error at address 0x2: file=0x49, mem=0xff >> I have tried the suggestions that I found on this list but no one have >> fixed my problem :( >> Any suggestion ? >> Thank you so much!! >> >> -- >> Léa >> >> <http://www.das.ufsc.br/%7Eunderlea/> >> >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> Tinyos-help mailing list >> [email protected] >> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help >> > -- Underléa Cabreira Corrêa, PhD student - [EMAIL PROTECTED] Department of Automation and Systems Federal University of Santa Catarina Florianópolis, SC - Brazil phone: +55 48 84296933 http://www.das.ufsc.br/~underlea/
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
