Hi,
I am trying to compile and install the blink application for an irismote
using MIB520 and tinyos-2.x
I can get the application to compile. But I can't get it to install. I am
not sure what to do. Any suggestions? I have tried install.0, install.42 etc
- I get the same output...
The output is below. Thanks,
Rahul
Compiling seems to work:
--------------------------------------------------------------------------------------------------------
$ make iris
mkdir -p build/iris
compiling BlinkAppC to a iris binary
ncc -o build/iris/main.exe -Os -Wall -Wshadow -Wnesc-all -target=iris
-fnesc-cfile=build/iris/app.c -board=micasb -DDEFINED_TOS_AM_GROUP=0x22
--param max-inline-insns-single=100000 -DIDENT_APPNAME=\"BlinkAppC\"
-DIDENT_USERNAME=\"monday\" -DIDENT_HOSTNAME=\"Monday\"
-DIDENT_USERHASH=0x6fc7776cL -DIDENT_TIMESTAMP=0x493a0c69L
-DIDENT_UIDHASH=0x1df5c139L -fnesc-dump=wiring
-fnesc-dump='interfaces(!abstract())' -fnesc-dump='referenced(interfacedefs,
components)' -fnesc-dumpfile=build/iris/wiring-check.xml
BlinkAppC.nc<http://blinkappc.nc/>-lm
compiled BlinkAppC to build/iris/main.exe
2268 bytes in ROM
51 bytes in RAM
avr-objcopy --output-target=srec build/iris/main.exe build/iris/main.srec
avr-objcopy --output-target=ihex build/iris/main.exe build/iris/main.ihex
writing TOS image
installation gives all sorts of strange messages
------------------------------------------------------------------------------------------------------------------------------
$ make iris install.0 mib520,/dev/ttyUSB0
mkdir -p build/iris
compiling BlinkAppC to a iris binary
ncc -o build/iris/main.exe -Os -Wall -Wshadow -Wnesc-all -target=iris
-fnesc-cfile=build/iris/app.c -board=micasb -DDEFINED_TOS_AM_GROUP=0x22
--param max-inline-insns-single=100000 -DIDENT_APPNAME=\"BlinkAppC\"
-DIDENT_USERNAME=\"monday\" -DIDENT_HOSTNAME=\"Monday\"
-DIDENT_USERHASH=0x6fc7776cL -DIDENT_TIMESTAMP=0x493a0c84L
-DIDENT_UIDHASH=0x12371ebeL -fnesc-dump=wiring
-fnesc-dump='interfaces(!abstract())' -fnesc-dump='referenced(interfacedefs,
components)' -fnesc-dumpfile=build/iris/wiring-check.xml
BlinkAppC.nc<http://blinkappc.nc/>-lm
compiled BlinkAppC to build/iris/main.exe
2268 bytes in ROM
51 bytes in RAM
avr-objcopy --output-target=srec build/iris/main.exe build/iris/main.srec
avr-objcopy --output-target=ihex build/iris/main.exe build/iris/main.ihex
writing TOS image
tos-set-symbols build/iris/main.srec build/iris/main.srec.out-0
TOS_NODE_ID=0 ActiveMessageAddressC$addr=0
Could not find data section in build/iris/main.exe, aborting.
Could not find symbol ActiveMessageAddressC$addr in build/iris/main.exe,
ignoring symbol.
Could not find symbol TOS_NODE_ID in build/iris/main.exe, ignoring symbol.
installing iris binary using mib510
avrdude -cmib510 -P/dev/ttyUSB0 -U hfuse:w:0xd9:m -pm1281 -U efuse:w:0xff:m
-C/etc/avrdude/avrdude.conf -U flash:w:build/iris/main.srec.out-0:a
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.05s
avrdude: Device signature = 0xffffff
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
avrdude done. Thank you.
make: *** [program] Error 1
_______________________________________________
Tinyos-help mailing list
[email protected]
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
