Hi,
I've the following trouble executing BlinkToRadio program as explained in
TinyOS tutorials part 3.
make micaz install -----> returns the following
mkdir -p build/micaz
compiling BlinkToRadioAppC to a micaz binary
ncc -o build/micaz/main.exe -Os -fnesc-separator=__ -Wall -Wshadow
-Wnesc-all -target=micaz -fnesc-cfile=build/micaz/app.c -board=micasb
-DDEFINED_TOS_AM_GROUP=0x22 --param max-inline-insns-single=100000
-DIDENT_APPNAME=\"BlinkToRadioApp\" -DIDENT_USERNAME=\"root\"
-DIDENT_HOSTNAME=\"dolphin-laptop\" -DIDENT_USERHASH=0xab8172f9L
-DIDENT_TIMESTAMP=0x4c659e35L -DIDENT_UIDHASH=0x60d2e1a7L -fnesc-dump=wiring
-fnesc-dump='interfaces(!abstract())' -fnesc-dump='referenced(interfacedefs,
components)' -fnesc-dumpfile=build/micaz/wiring-check.xml
BlinkToRadioAppC.nc -lm
/opt/tinyos-2.1.1/tos/chips/cc2420/lpl/DummyLplC.nc:39:2: warning: #warning
"*** LOW POWER COMMUNICATIONS DISABLED ***"
compiled BlinkToRadioAppC to build/micaz/main.exe
11656 bytes in ROM
311 bytes in RAM
avr-objcopy --output-target=srec build/micaz/main.exe build/micaz/main.srec
avr-objcopy --output-target=ihex build/micaz/main.exe build/micaz/main.ihex
writing TOS image
cp build/micaz/main.srec build/micaz/main.srec.out
installing micaz binary using dapa
uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128
--wr_fuse_e=ff --erase --upload if=build/micaz/main.srec.out --verify
/dev/parport0: No such file or directory
Failed to open ppdev.
make: *** [program] Error 2
When I install the same on micaz mote, it installs fine but when I power on
the mote (after taking off the board) with batteries, the leds just wouldn't
blink! This is the output of the command:
make micaz install mib510,/dev/ttyUSB0
mkdir -p build/micaz
compiling BlinkToRadioAppC to a micaz binary
ncc -o build/micaz/main.exe -Os -fnesc-separator=__ -Wall -Wshadow
-Wnesc-all -target=micaz -fnesc-cfile=build/micaz/app.c -board=micasb
-DDEFINED_TOS_AM_GROUP=0x22 --param max-inline-insns-single=100000
-DIDENT_APPNAME=\"BlinkToRadioApp\" -DIDENT_USERNAME=\"root\"
-DIDENT_HOSTNAME=\"dolphin-laptop\" -DIDENT_USERHASH=0xab8172f9L
-DIDENT_TIMESTAMP=0x4c659dadL -DIDENT_UIDHASH=0x1521a22eL -fnesc-dump=wiring
-fnesc-dump='interfaces(!abstract())' -fnesc-dump='referenced(interfacedefs,
components)' -fnesc-dumpfile=build/micaz/wiring-check.xml
BlinkToRadioAppC.nc -lm
/opt/tinyos-2.1.1/tos/chips/cc2420/lpl/DummyLplC.nc:39:2: warning: #warning
"*** LOW POWER COMMUNICATIONS DISABLED ***"
compiled BlinkToRadioAppC to build/micaz/main.exe
11656 bytes in ROM
311 bytes in RAM
avr-objcopy --output-target=srec build/micaz/main.exe build/micaz/main.srec
avr-objcopy --output-target=ihex build/micaz/main.exe build/micaz/main.ihex
writing TOS image
cp build/micaz/main.srec build/micaz/main.srec.out
installing micaz binary using mib510
uisp -dprog=mib510 -dserial=/dev/ttyUSB0 --wr_fuse_h=0xd9 -dpart=ATmega128
--wr_fuse_e=ff --erase --upload if=build/micaz/main.srec.out --verify
Firmware Version: 2.1
Atmel AVR ATmega128 is found.
Uploading: flash
Verifying: flash
Fuse High Byte set to 0xd9
Fuse Extended Byte set to 0xff
rm -f build/micaz/main.exe.out build/micaz/main.srec.out
Would be great if anyone can help me!
Regards,
--
Bhanu Kishore
http://bhanukishore.blogspot.com/
The only lines that matter are the ones you make.
_______________________________________________
Tinyos-help mailing list
[email protected]
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
