Hi I had upgrade from TOS v1 to v2 as per step mentioned
below.http://www.tinyos.net/tinyos-2.x/doc/html/upgrade-tinyos.html while
giving" make micaz reinstall mib520,/dev/ttys3" command. I am getting
############################Command: make micaz reinstall
mib520,/dev/ttys3Cygwin: E:\Crossbow\cygwin\binDirectory:
E:\Crossbow\cygwin\opt\tinyos-2.x\apps\Blink\"/opt/MoteWorks/tools/bin/ide.pl
'make micaz reinstall mib520,/dev/ttys3'
'E:\Crossbow\cygwin\opt\tinyos-2.x\apps\Blink\'"#############################ide.pl
Ver:$Id: ide.pl,v 1.1.2.1 2006/05/29 07:22:52 lwei Exp $Executing:
/opt/tinyos-2.x/apps/Blink/ bash -c "make micaz reinstall mib520,/dev/ttys3"cp
build/micaz/main.srec build/micaz/main.srec.out installing micaz binary with
dapauisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff
--erase Atmel AVR ATmega128 is found.Erasing device ...Reinitializing
deviceAtmel AVR ATmega128 is found.pulsepulse Fuse High Byte set to 0xd9 Fuse
Extended Byte set to 0xffsleep 1 uisp -dprog=dapa --wr_fuse_h=0xd9
-dpart=ATmega128 --wr_fuse_e=ff --upload if=build/micaz/main.srec.outAtmel AVR
ATmega128 is
found.Uploading: flashpulse Fuse High Byte set to 0xd9 Fuse Extended Byte set
to 0xffsleep 1 uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128
--wr_fuse_e=ff --verify if=build/micaz/main.srec.outAtmel AVR ATmega128 is
found.Verifying: flashflash error at address 0x0: file=0x0c, mem=0xffflash
error at address 0x1: file=0x94, mem=0xffflash error at address 0x2: file=0x49,
mem=0xffflash error at address 0x3: file=0x00, mem=0xffflash error at address
0x4: file=0x0c, mem=0xffflash error at address 0x5: file=0x94, mem=0xffflash
error at address 0x6: file=0x66, mem=0xffflash error at address 0x7: file=0x00,
mem=0xffflash error at address 0x8: file=0x0c, mem=0xffflash error at address
0x9: file=0x94, mem=0xff.................flash error at address 0x8a4:
file=0x0f, mem=0xffflash error at address 0x8a5: file=0x90, mem=0xffflash error
at address 0x8a6: file=0x1f, mem=0xffflash error at address 0x8a7: file=0x90,
mem=0xffflash error at address
0x8a8: file=0x18, mem=0xffflash error at address 0x8a9: file=0x95,
mem=0xffpulse Fuse High Byte set to 0xd9 Fuse Extended Byte set to 0xffrm -f
build/micaz/main.exe.out build/micaz/main.srec.out > Process Exit Code: 0>
Time Taken: 02:09
Is it correct compilation?
With regardsSivasankar
With regards Sivasankar
_______________________________________________
Tinyos-help mailing list
[email protected]
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
