Hi Miklos,
We are working on BLIP-rpl code ... which we downloaded from Tinyos
svn repo tinyos-main.googlecode.com/svn/trunk/ tinyos-main-read-only
.. version we are using is r5510....
In this version BLIP uses cc2420 specific components at 2 files
IPDispatchC and Ieee154addressC, and i changed at these two places
and used Ieee154MessageC and ActiveMessageAddressC respectively..
but this code is not working for IRIS .. while analysing this i
found that rf230 radio is not starting at all... In the file
RF230DriverlayerP.nc the state of command 'cmd' is not changing to
CMC_SIGNAL_DONE it is remaining CMD_NONE only.... and hence this
component not signalling RadioState.done() to upper component... i
am not understanding why radio state is not changing ... do i need
to call any other additional command other than
splitControl.start()? to make radio start?... can i get any
documents on rf230 radio stack implementation which helps me to
understand its implementation?.... please help...
Thanks&Regards,
Shrikant U Hallur
Hi Shrikant,
>
> I never used BLIP, but I was trying to get the RF230 driver in shape
> to support BLIP. Can you point to which version of BLIP are you using?
> Where are you downloading it?
>
> As far as I know, Ieee154MessageC worked on IRIS.
>
> Best,
> Miklos
>
> On Thu, May 12, 2011 at 11:50 AM, Shrikant U Hallur
> <[email protected]> wrote:
>>
>> Hello All,
>>
>> I am Shrikant from IISc Bangalore. i am trying to port BLIP/RPL
>> on Iris motes, I went through the code and found that code is
>> exclusivly written for CC2420 radio unlike the earlier BLIP/Hydro
>> where we could able to implement BLIP on Iris... So i did the
>> following changes in the BLIP/RPL code in order to make it work on
>> Iris.
>>
>> I found that in BLIP code two files 'IPDispatchC.nc' and
>> 'Ieee154AddressC.nc' are wired to CC2420 specific components, i
>> changed those wiring and wired IPDispatchP to Ieee154MessageC
>> instead of CC2420RadioC and wired Ieee154AddressP to
>> ActiveMessageAddressC instead of CC2420ControlC, (same way as in
>> earlier BLIP/Hydro code) and made correspondent changes in there
>> interfaces also..
>>
>> The modified code works well with TelosB motes, i can able to ping
>> motes successfully, but code is not working for Iris, it was
>> compilling successfully but Iris mote is not sending any kind of
>> messages.
>>
>> While analysing the problem i found IPDispatchP is not getting
>> 'RadioControl.startDone' event,but it is successfully calling
>> RadioControl.start command to Ieee154MessageC. That means to say
>> Ieee154MessageC component found under /tos/platforms/iris/ is not
>> sending the required event.... is the available Ieee154MessageC in
>> Iris is proper working code?.. or i am missing something in this
>> porting process?.. and which is making existing Ieee154MessageC not
>> to work correctly?...
>>
>> Please help me in this... is there anybody working in making
>> BLIP/RPL code independent of platforms? or is ther any recent
>> version which already have this?... kindly help...
>>
>>
>> Regards,
>> Shrikant U Hallur
>> IISC, Bangalore.
>>
>>
>>
>>
>> --
>> This message has been scanned for viruses and
>> dangerous content by MailScanner, and is
>> believed to be clean.
>>
>>
>
> --
> This message has been scanned for viruses and
> dangerous content by MailScanner, and is
> believed to be clean.
>
>
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
_______________________________________________
Tinyos-help mailing list
[email protected]
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
