yes ----- Original Message ----- From: Mubashir Rehmani To: André Rodrigues Cc: Eric Decker ; [email protected] Sent: Wednesday, February 29, 2012 9:57 AM Subject: Re: [Tinyos-help] ADC port
Hi Angré, Yes, all i want is to have output 0 or 1 on pin 10. If i clearly understood, port 6.3 is pin 10 (ADC3) of expansion connector U2? Kind Regards 2012/2/29 André Rodrigues <[email protected]> Hi If all you want is to output 0 or 1 on pin 10, I would say that you just have to use port 6.3. In that case you do not neet to use any resistors. But Eric could confirm (or not) my opinion. Next, study one of the available device drivers to learn how to select the port for IO and how to set/clr the bit. Regards, André ----- Original Message ----- From: Mubashir Rehmani To: Eric Decker Cc: [email protected] Sent: Wednesday, February 29, 2012 9:23 AM Subject: Re: [Tinyos-help] ADC port Thanks Eric for your answer. In fact, in the telosb motive data sheet, http://moss.csc.ncsu.edu/~mueller/rt/rt11/readings/projects/g4/datasheet.pdf It is written on page 24 that "If expansion pin 10 (ADC3) is used for digital I/O instead of analog inputs, R14 must be populated with a 0 ohm resistor to enable the pin for digital I/O (GIO0) on the microcontroller. R16 must be populated with a 0 ohm resistor to enable GIO1. R14 and R16 are located on the top side of Telos between the USB controller and the radio." So, what i want to do is that i want to use the expansion pin 10 (ADC3) and control the I/O signals through tinyos. More precisely, i want to attach an electronic switch, which enables or disable an external device (antenna) with the signal i provide it to this expansion pin 10 (ADC3). Do you have any idea how to achieve this? Kind Regards On 29 February 2012 10:16, Eric Decker <[email protected]> wrote: On Tue, Feb 28, 2012 at 11:58 PM, Mubashir Rehmani <[email protected]> wrote: Dear All, I want to control the I/O of the 10-pin extension connector of (U2) of the Telosb mote. In fact, i want to use ADC3 and control its power level in order to connect the digital switch with it. Can anyone tell me how i can control the voltage level of this ADC3 from the tinyos code? you aren't understanding how this ADC stuff really works...... ADC3 is an input to the ADC subsystem so it is nonsensical to talk about controlling the voltage level from the tinyos code. I suggest that you read the TI msp430f1611 manual in conjunction with the moteiv telosb schematic to understand what hardware is provided and how it works. Please refer the pin diagram of the datasheet (page 23) http://moss.csc.ncsu.edu/~mueller/rt/rt11/readings/projects/g4/datasheet.pdf Kind Regards -- Mubashir Husain Rehmani _______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help -- Eric B. Decker Senior (over 50 :-) Researcher -- Mubashir Husain Rehmani -------------------------------------------------------------------------- _______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help -- Mubashir Husain Rehmani
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
