I'm using 1.2.14-ish. I've noticed jkstatus sometimes works, sometimes not with IIS 6.
workers.properties: # #------ DEFAULT worket list ------------------------------------------ #--------------------------------------------------------------------- # # # The workers that your plugins should create and work with # The name of the worker can contain only the alphanumeric characters # [a-z][A-Z][0-9] and is case insensitive. # # Add 'inprocess' if you want JNI connector worker.list=loadbalancer,loadbalancer2,jkstatus # #------ DEFAULT ajp13 WORKER DEFINITION ------------------------------ #--------------------------------------------------------------------- # # # Defining a worker named ajp13 and of type ajp13 # Note that the name and the type do not have to match. # worker.qailt005:8009.port=8009 worker.qailt005:8009.host=qailt005 worker.qailt005:8009.type=ajp13 worker.qailt005:8009.cache_timeout=600 # # Specifies the load balance factor when used with # a load balancing worker. # Note: # ----> lbfactor must be > 0 # ----> Low lbfactor means less work done by the worker. worker.qailt005:8009.lbfactor=1 # # Specify the size of the open connection cache. worker.qailt005:8009.cachesize=100 # worker.qailt006:8009.port=8009 worker.qailt006:8009.host=qailt006 worker.qailt006:8009.type=ajp13 worker.qailt006:8009.cache_timeout=600 # # Specifies the load balance factor when used with # a load balancing worker. # Note: # ----> lbfactor must be > 0 # ----> Low lbfactor means less work done by the worker. worker.qailt006:8009.lbfactor=1 # # Specify the size of the open connection cache. worker.qailt006:8009.cachesize=100 worker.dwqa2:8009.port=8009 worker.dwqa2:8009.host=dwqa2 worker.dwqa2:8009.type=ajp13 worker.dwqa2:8009.lbfactor=1 worker.dwqa2:8009.cachesize=100 worker.dwqa2:8009.cache_timeout=600 worker.dwqa3:8009.port=8009 worker.dwqa3:8009.host=dwqa3 worker.dwqa3:8009.type=ajp13 worker.dwqa3:8009.lbfactor=1 worker.dwqa3:8009.cachesize=100 worker.dwqa3:8009.cache_timeout=600 # #------ DEFAULT LOAD BALANCER WORKER DEFINITION ---------------------- #--------------------------------------------------------------------- # # # The loadbalancer (type lb) workers perform wighted round-robin # load balancing with sticky sessions. # Note: # ----> If a worker dies, the load balancer will check its state # once in a while. Until then all work is redirected to peer # workers. # These workers should not appear in the worker.list property! worker.loadbalancer.type=lb worker.loadbalancer.balance_workers=qailt005:8009,qailt006:8009 worker.loadbalancer.sticky_session=1 worker.loadbalancer.method=T worker.loadbalancer2.type=lb worker.loadbalancer2.balance_workers=dwqa2:8009,dwqa3:8009 worker.loadbalancer2.sticky_session=1 worker.jkstatus.type=status uriworkermap.properties: /iltlbtesting=loadbalancer /iltlbtesting/*=loadbalancer /iltscripting=loadbalancer /iltscripting/*=loadbalancer /iltlbtestingalt=loadbalancer /iltlbtestingalt/*=loadbalancer /dmlbilt=loadbalancer /dmlbilt/*=loadbalancer /DM6247QA6201=loadbalancer2 /DM6247QA6201/*=loadbalancer2 /lb6255Master_arm=loadbalancer2 /lb6255Master_arm/*=loadbalancer2 /QA6201CFLB6247DM=loadbalancer2 /QA6201CFLB6247DM/*=loadbalancer2 /QA6201CFLB6255DM=loadbalancer2 /QA6201CFLB6255DM/*=loadbalancer2 /DM42=loadbalancer2 /DM42/*=loadbalancer2 /jkstatus=jkstatus /jkstatus/*=jkstatus -----Original Message----- From: Sumpter, Chuck [mailto:[EMAIL PROTECTED] Sent: Thursday, July 21, 2005 10:36 AM To: [email protected] Subject: IIS6 Win2003 ISAPI config Jk1.2 in this environment works fine, except for jkstatus. I've worked through the how-to's and examples on the Tomcat connectors site, including the workers how-to. The jkstatus page gets a 404 every time. Does anyone have example workers.properties and uriworkermap.properties that they would be willing to post? --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
