Hi,
I am using fedora 10 and k3b for burning. I am trying to burn an ISO image
on DVD and I am getting the following error.
cdrecord returned an unknown error (code 254).
And here is the entire debug output.
Devices
-----------------------
HL-DT-ST
DVD-RAM GH22NS30 1.01 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R,
DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential,
DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW
Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual
Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R,
RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump] [%7]
System
-----------------------
K3b Version: 1.66.0
KDE Version: 4.2.3 (KDE 4.2.3)
QT Version: 4.5.0
Kernel: 2.6.27.21-170.2.56.fc10.x86_64
Used versions
-----------------------
cdrecord: 2.1.1a03
cdrecord
-----------------------
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.8
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identification : 'DVD-RAM GH22NS30'
Revision : '1.01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0011 (DVD-R sequential recording)
Profile: 0x0012 (DVD-RAM)
Profile: 0x002B (DVD+R/DL)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0011 (DVD-R sequential recording) (current)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW)
Profile: 0x0009 (CD-R)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc DVD-R(W) driver (mmc_mdvd).
Driver flags : SWABAUDIO BURNFREE
Supported modes: PACKET SAO
Drive buf size : 1409024 = 1376 KB
Drive DMA Speed: 137259 kB/s 779x CD 99x DVD
FIFO size : 4194304 = 4096 KB
Speed set to 5540 KB/s
Track 01: data 167 MB
Total size: 192 MB (19:06.48) = 85986 sectors
Lout start: 193 MB (19:08/36) = 85986 sectors
Current Secsize: 2048
HINT: use dvd+rw-mediainfo from dvd+rw-tools for information extraction.
Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 2212510
Starting to write CD/DVD at speed 4.0 in real force SAO mode for single
session.
Last chance to quit, starting real write in 2 seconds.
1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
Starting new track at sector: 0
Track 01: 0 of 167 MB written.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 00 00 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 0C 80 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x0C Qual 0x80 (write error) [No matching qualifier] Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 2.054s timeout 200s
wodim: A write error occured.
wodim: Please properly read the error message above.
write track data: error after 0 bytes
Writing time: 13.911s
Average write speed 18.1x.
Fixating...
Fixating time: 0.002s
wodim: fifo had 64 puts and 1 gets.
wodim: fifo was 0 times empty and 0 times full, min fill was 100%.
cdrecord command:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=/dev/sr0 speed=4 -sao driveropts=burnfree
-force -ignsize -data -tsize=85986s -
---
Thanks,
Ravikanth
