On Sat, May 17, 2025 at 09:28:00PM +0000, OMAP at BSF wrote:
> * Converted to using DM_I2C.
> * New config file for xM.
> * Run 'patman' on patches.
> * Use upstream device tree files.
>
> Signed-off-by: Steven Hill <omap...@protonmail.com>
> ---
> v2: Use upstream device trees.
> v3: No change.
> v4: Update name in MAINTAINERS file.
>
> ---
> arch/arm/dts/Makefile | 9 +
> arch/arm/dts/omap3-beagle-u-boot.dtsi | 14 +
> arch/arm/dts/omap3-beagle-xm-ab-u-boot.dtsi | 14 +
> arch/arm/dts/omap3-beagle-xm-u-boot.dtsi | 14 +
> arch/arm/dts/omap3-u-boot.dtsi | 34 +-
> arch/arm/include/asm/arch-omap3/cpu.h | 3 +-
> arch/arm/include/asm/arch-omap3/hardware.h | 22 +
> arch/arm/include/asm/arch-omap3/mem.h | 8 +-
> arch/arm/mach-omap2/omap3/Kconfig | 14 +
> board/beagle/beagle/Kconfig | 14 +
> board/beagle/beagle/MAINTAINERS | 7 +
> board/beagle/beagle/Makefile | 7 +
> board/beagle/beagle/beagle.c | 541 +++++++++++++++++++
> board/beagle/beagle/beagle.h | 545 ++++++++++++++++++++
> board/beagle/beagle/led.c | 70 +++
> board/isee/igep00x0/spl.c | 6 +-
> board/lg/sniper/sniper.c | 2 +-
> board/logicpd/omap3som/omap3logic.c | 4 +-
> board/ti/omap3evm/evm.c | 2 +-
> board/timll/devkit8000/devkit8000.c | 2 +-
> configs/omap3_beagle_defconfig | 124 +++++
> configs/omap3_beagle_xm_defconfig | 109 ++++
> include/configs/omap3_beagle.h | 201 ++++++++
> 23 files changed, 1736 insertions(+), 30 deletions(-)
> create mode 100644 arch/arm/dts/omap3-beagle-u-boot.dtsi
> create mode 100644 arch/arm/dts/omap3-beagle-xm-ab-u-boot.dtsi
> create mode 100644 arch/arm/dts/omap3-beagle-xm-u-boot.dtsi
> create mode 100644 arch/arm/include/asm/arch-omap3/hardware.h
> create mode 100644 board/beagle/beagle/Kconfig
> create mode 100644 board/beagle/beagle/MAINTAINERS
> create mode 100644 board/beagle/beagle/Makefile
> create mode 100644 board/beagle/beagle/beagle.c
> create mode 100644 board/beagle/beagle/beagle.h
> create mode 100644 board/beagle/beagle/led.c
> create mode 100644 configs/omap3_beagle_defconfig
> create mode 100644 configs/omap3_beagle_xm_defconfig
> create mode 100644 include/configs/omap3_beagle.h
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 32b698a7f41..ceb6dade534 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -966,6 +966,15 @@ dtb-$(CONFIG_TARGET_GARDENA_SMART_GATEWAY_AT91SAM) += \
>
> dtb-$(CONFIG_TARGET_USB_A9263) += usb_a9263.dtb
>
> +dtb-$(CONFIG_TARGET_OMAP3_EVM) += \
> + omap3-evm-37xx.dtb \
> + omap3-evm.dtb
> +
> +dtb-$(CONFIG_TARGET_OMAP3_BEAGLE) += \
> + omap3-beagle-xm-ab.dtb \
> + omap3-beagle-xm.dtb \
> + omap3-beagle.dtb
> +
> dtb-$(CONFIG_TARGET_DEVKIT8000) += omap3-devkit8000.dtb
>
> dtb-$(CONFIG_TARGET_SAMA7G5EK) += \
> diff --git a/arch/arm/dts/omap3-beagle-u-boot.dtsi
> b/arch/arm/dts/omap3-beagle-u-boot.dtsi
> new file mode 100644
> index 00000000000..2c03701c896
> --- /dev/null
> +++ b/arch/arm/dts/omap3-beagle-u-boot.dtsi
> @@ -0,0 +1,14 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * U-Boot additions
> + *
> + * (C) Copyright 2017 Derald D. Woods <woods.techni...@gmail.com>
> + */
> +
> +#include "omap3-u-boot.dtsi"
> +
> +/ {
> + chosen {
> + stdout-path = &uart3;
> + };
> +};
> diff --git a/arch/arm/dts/omap3-beagle-xm-ab-u-boot.dtsi
> b/arch/arm/dts/omap3-beagle-xm-ab-u-boot.dtsi
> new file mode 100644
> index 00000000000..2c03701c896
> --- /dev/null
> +++ b/arch/arm/dts/omap3-beagle-xm-ab-u-boot.dtsi
> @@ -0,0 +1,14 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * U-Boot additions
> + *
> + * (C) Copyright 2017 Derald D. Woods <woods.techni...@gmail.com>
> + */
> +
> +#include "omap3-u-boot.dtsi"
> +
> +/ {
> + chosen {
> + stdout-path = &uart3;
> + };
> +};
> diff --git a/arch/arm/dts/omap3-beagle-xm-u-boot.dtsi
> b/arch/arm/dts/omap3-beagle-xm-u-boot.dtsi
> new file mode 100644
> index 00000000000..2c03701c896
> --- /dev/null
> +++ b/arch/arm/dts/omap3-beagle-xm-u-boot.dtsi
> @@ -0,0 +1,14 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * U-Boot additions
> + *
> + * (C) Copyright 2017 Derald D. Woods <woods.techni...@gmail.com>
> + */
> +
> +#include "omap3-u-boot.dtsi"
> +
> +/ {
> + chosen {
> + stdout-path = &uart3;
> + };
> +};
> diff --git a/arch/arm/dts/omap3-u-boot.dtsi b/arch/arm/dts/omap3-u-boot.dtsi
> index bc2793757b7..b17790e758b 100644
> --- a/arch/arm/dts/omap3-u-boot.dtsi
> +++ b/arch/arm/dts/omap3-u-boot.dtsi
> @@ -9,74 +9,74 @@
>
> /{
> ocp@68000000 {
> - bootph-pre-ram;
> + bootph-all;
>
> bandgap@48002524 {
> - bootph-pre-ram;
> + bootph-all;
> };
> };
> };
>
> &uart1 {
> - bootph-pre-ram;
> + bootph-all;
> reg-shift = <2>;
> };
>
> &uart2 {
> - bootph-pre-ram;
> + bootph-all;
> reg-shift = <2>;
> };
>
> &uart3 {
> - bootph-pre-ram;
> + bootph-all;
> reg-shift = <2>;
> };
>
> &mmc1 {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &mmc2 {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &l4_core {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &scm {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &scm_conf {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &gpio1 {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &gpio2 {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &gpio3 {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &gpio4 {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &gpio5 {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &gpio6 {
> - bootph-pre-ram;
> + bootph-all;
> };
>
> &i2c1 {
> - bootph-pre-ram;
> + bootph-all;
> clock-frequency = <100000>;
> };
> diff --git a/arch/arm/include/asm/arch-omap3/cpu.h
> b/arch/arm/include/asm/arch-omap3/cpu.h
> index d2fbf919a5b..917e7def378 100644
> --- a/arch/arm/include/asm/arch-omap3/cpu.h
> +++ b/arch/arm/include/asm/arch-omap3/cpu.h
> @@ -12,6 +12,8 @@
> #include <asm/types.h>
> #endif /* !(__KERNEL_STRICT_NAMES || __ASSEMBLY__) */
>
> +#include <asm/arch/hardware.h>
> +
> /* Register offsets of common modules */
> /* Control */
> #ifndef __KERNEL_STRICT_NAMES
> @@ -67,7 +69,6 @@ struct ctrl_id {
> #define SKUID_CLK_600MHZ 0x0
> #define SKUID_CLK_720MHZ 0x8
>
> -#define GPMC_BASE (OMAP34XX_GPMC_BASE)
> #define GPMC_CONFIG_CS0 0x60
> #define GPMC_CONFIG_CS0_BASE (GPMC_BASE + GPMC_CONFIG_CS0)
>
> diff --git a/arch/arm/include/asm/arch-omap3/hardware.h
> b/arch/arm/include/asm/arch-omap3/hardware.h
> new file mode 100644
> index 00000000000..108830912ad
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-omap3/hardware.h
> @@ -0,0 +1,22 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * hardware.h
> + *
> + * hardware specific header
> + *
> + * Copyright (C) 2013, Texas Instruments, Incorporated - http://www.ti.com/
> + */
> +
> +#ifndef __OMAP_HARDWARE_H
> +#define __OMAP_HARDWARE_H
> +
> +#include <asm/arch/omap.h>
> +
> +/*
> + * Common hardware definitions
> + */
> +
> +/* GPMC Base address */
> +#define GPMC_BASE (OMAP34XX_GPMC_BASE)
> +
> +#endif
> diff --git a/arch/arm/include/asm/arch-omap3/mem.h
> b/arch/arm/include/asm/arch-omap3/mem.h
> index 2b6cfde4114..e5b57ca0dbf 100644
> --- a/arch/arm/include/asm/arch-omap3/mem.h
> +++ b/arch/arm/include/asm/arch-omap3/mem.h
> @@ -37,10 +37,10 @@ enum {
> * enable at bits 0:1 and an autorefresh counter value in bits 8:23. The
> * counter is a result of ( tREFI / tCK ) - 50.
> */
> -#define SDP_3430_SDRC_RFR_CTRL_100MHz 0x0002da01
> -#define SDP_3430_SDRC_RFR_CTRL_133MHz 0x0003de01 /* 7.8us/7.5ns -
> 50=0x3de */
> -#define SDP_3430_SDRC_RFR_CTRL_165MHz 0x0004e201 /* 7.8us/6ns -
> 50=0x4e2 */
> -#define SDP_3430_SDRC_RFR_CTRL_200MHz 0x0005e601 /* 7.8us/5ns -
> 50=0x5e6 */
> +#define SDP_3430_SDRC_RFR_CTRL_100MHZ 0x0002da01
> +#define SDP_3430_SDRC_RFR_CTRL_133MHZ 0x0003de01 /* 7.8us/7.5ns -
> 50=0x3de */
> +#define SDP_3430_SDRC_RFR_CTRL_165MHZ 0x0004e201 /* 7.8us/6ns -
> 50=0x4e2 */
> +#define SDP_3430_SDRC_RFR_CTRL_200MHZ 0x0005e601 /* 7.8us/5ns -
> 50=0x5e6 */
>
> #define DLL_OFFSET 0
> #define DLL_WRITEDDRCLKX2DIS 1
> diff --git a/arch/arm/mach-omap2/omap3/Kconfig
> b/arch/arm/mach-omap2/omap3/Kconfig
> index b50b8a5f6bd..ed8dc77a353 100644
> --- a/arch/arm/mach-omap2/omap3/Kconfig
> +++ b/arch/arm/mach-omap2/omap3/Kconfig
> @@ -34,6 +34,19 @@ config TARGET_AM3517_EVM
> select MMC
> imply CMD_DM
>
> +config TARGET_OMAP3_BEAGLE
> + bool "TI OMAP3 BeagleBoard"
> + select DM
> + select DM_GPIO
> + select DM_I2C
> + select DM_SERIAL
> + select OMAP3_GPIO_5
> + select OMAP3_GPIO_6
> + select TI_I2C_BOARD_DETECT
> + select SUPPORT_EXTENSION_SCAN
> + imply CMD_DM
> + imply OF_UPSTREAM
> +
> config TARGET_CM_T35
> bool "CompuLab CM-T3530 and CM-T3730 boards"
> select OMAP3_GPIO_2
> @@ -145,6 +158,7 @@ config SYS_SOC
> default "omap3"
>
> source "board/logicpd/am3517evm/Kconfig"
> +source "board/beagle/beagle/Kconfig"
> source "board/timll/devkit8000/Kconfig"
> source "board/ti/omap3evm/Kconfig"
> source "board/isee/igep00x0/Kconfig"
> diff --git a/board/beagle/beagle/Kconfig b/board/beagle/beagle/Kconfig
> new file mode 100644
> index 00000000000..7e8fb365698
> --- /dev/null
> +++ b/board/beagle/beagle/Kconfig
> @@ -0,0 +1,14 @@
> +if TARGET_OMAP3_BEAGLE
> +
> +config SYS_BOARD
> + default "beagle"
> +
> +config SYS_VENDOR
> + default "beagle"
> +
> +config SYS_CONFIG_NAME
> + default "omap3_beagle"
> +
> +endif
> +
> +source "board/ti/common/Kconfig"
> diff --git a/board/beagle/beagle/MAINTAINERS b/board/beagle/beagle/MAINTAINERS
> new file mode 100644
> index 00000000000..70e71b6a7ed
> --- /dev/null
> +++ b/board/beagle/beagle/MAINTAINERS
> @@ -0,0 +1,7 @@
> +BEAGLE BOARD
> +M: Steven Hill <omap...@protonmail.com>
> +S: Maintained
> +F: board/beagle/beagle/
> +F: include/configs/omap3_beagle.h
> +F: configs/omap3_beagle_defconfig
> +F: configs/omap3_beagle_xm_defconfig
> diff --git a/board/beagle/beagle/Makefile b/board/beagle/beagle/Makefile
> new file mode 100644
> index 00000000000..fc9288cf186
> --- /dev/null
> +++ b/board/beagle/beagle/Makefile
> @@ -0,0 +1,7 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# (C) Copyright 2000, 2001, 2002
> +# Wolfgang Denk, DENX Software Engineering, w...@denx.de.
> +
> +obj-y := beagle.o
> +obj-$(CONFIG_LED_STATUS) += led.o
> diff --git a/board/beagle/beagle/beagle.c b/board/beagle/beagle/beagle.c
> new file mode 100644
> index 00000000000..660a50afd0d
> --- /dev/null
> +++ b/board/beagle/beagle/beagle.c
> @@ -0,0 +1,541 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * (C) Copyright 2004-2011
> + * Texas Instruments, <www.ti.com>
> + *
> + * Author :
> + * Sunil Kumar <sunilsain...@gmail.com>
> + * Shashi Ranjan <shashiranjanmc...@gmail.com>
> + *
> + * Derived from Beagle Board and 3430 SDP code by
> + * Richard Woodruff <r-woodru...@ti.com>
> + * Syed Mohammed Khasim <kha...@ti.com>
> + *
> + */
> +#include <bootstage.h>
> +#include <dm.h>
> +#include <env.h>
> +#include <init.h>
> +#include <net.h>
> +#include <ns16550.h>
> +#include <serial.h>
> +#if (IS_ENABLED(CONFIG_LED_STATUS))
> +#include <status_led.h>
> +#endif
> +#include <twl4030.h>
> +#include <asm/global_data.h>
> +#include <linux/mtd/rawnand.h>
> +#include <asm/io.h>
> +#include <asm/arch/mmc_host_def.h>
> +#include <i2c.h>
> +#include <asm/arch/mux.h>
> +#include <asm/arch/mem.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/gpio.h>
> +#include <asm/mach-types.h>
> +#include <asm/omap_musb.h>
> +#include <linux/errno.h>
> +#include <linux/usb/ch9.h>
> +#include <linux/usb/gadget.h>
> +#include <linux/usb/musb.h>
> +#include "beagle.h"
> +#include <command.h>
> +
> +#define TWL4030_I2C_BUS 0
> +
> +#define TINCANTOOLS_ZIPPY 0x01000100
> +#define TINCANTOOLS_ZIPPY2 0x02000100
> +#define TINCANTOOLS_TRAINER 0x04000100
> +#define TINCANTOOLS_SHOWDOG 0x03000100
> +#define KBADC_BEAGLEFPGA 0x01000600
> +#define LW_BEAGLETOUCH 0x01000700
> +#define BRAINMUX_LCDOG 0x01000800
> +#define BRAINMUX_LCDOGTOUCH 0x02000800
> +#define BBTOYS_WIFI 0x01000B00
> +#define BBTOYS_VGA 0x02000B00
> +#define BBTOYS_LCD 0x03000B00
> +#define BCT_BRETTL3 0x01000F00
> +#define BCT_BRETTL4 0x02000F00
> +#define LSR_COM6L_ADPT 0x01001300
> +#define BEAGLE_NO_EEPROM 0xffffffff
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +static struct {
> + unsigned int device_vendor;
> + unsigned char revision;
> + unsigned char content;
> + char fab_revision[8];
> + char env_var[16];
> + char env_setting[64];
> +} expansion_config;
> +
> +/*
> + * Routine: board_init
> + * Description: Early hardware init.
> + */
> +int board_init(void)
> +{
> + gpmc_init(); /* in SRAM or SDRAM, finish GPMC */
> + /* board id for Linux */
> + gd->bd->bi_arch_number = MACH_TYPE_OMAP3_BEAGLE;
> + /* boot param addr */
> + gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
> +
> +#if (IS_ENABLED(CONFIG_LED_STATUS)) &&
> (IS_ENABLED(CONFIG_LED_STATUS_BOOT_ENABLE))
> + status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_ON);
> +#endif
> +
> + return 0;
> +}
> +
> +#if (IS_ENABLED(CONFIG_SPL_OS_BOOT))
> +int spl_start_uboot(void)
> +{
> + /* break into full u-boot on 'c' */
> + if (serial_tstc() && serial_getc() == 'c')
> + return 1;
> +
> + return 0;
> +}
> +#endif /* CONFIG_SPL_OS_BOOT */
> +
> +/*
> + * Routine: get_board_revision
> + * Description: Detect if we are running on a Beagle revision Ax/Bx,
> + * C1/2/3, C4, xM Ax/Bx or xM Cx. This can be done by reading
> + * the level of GPIO173, GPIO172 and GPIO171. This should
> + * result in
> + * GPIO173, GPIO172, GPIO171: 1 1 1 => Ax/Bx
> + * GPIO173, GPIO172, GPIO171: 1 1 0 => C1/2/3
> + * GPIO173, GPIO172, GPIO171: 1 0 1 => C4
> + * GPIO173, GPIO172, GPIO171: 0 1 0 => xM Cx
> + * GPIO173, GPIO172, GPIO171: 0 0 0 => xM Ax/Bx
> + */
> +static int get_board_revision(void)
> +{
> + static int revision = -1;
> +
> + if (revision == -1) {
> + if (!gpio_request(171, "rev0") &&
> + !gpio_request(172, "rev1") &&
> + !gpio_request(173, "rev2")) {
> + gpio_direction_input(171);
> + gpio_direction_input(172);
> + gpio_direction_input(173);
> +
> + revision = gpio_get_value(173) << 2 |
> + gpio_get_value(172) << 1 |
> + gpio_get_value(171);
> + } else {
> + printf("Error: unable to acquire board revision
> GPIOs\n");
> + }
> + }
> +
> + return revision;
> +}
> +
> +#if (IS_ENABLED(CONFIG_SPL_BUILD))
> +/*
> + * Routine: get_board_mem_timings
> + * Description: If we use SPL then there is no x-loader nor config header
> + * so we have to setup the DDR timings ourself on both banks.
> + */
> +void get_board_mem_timings(struct board_sdrc_timings *timings)
> +{
> + int pop_mfr, pop_id;
> +
> + /*
> + * We need to identify what PoP memory is on the board so that
> + * we know what timings to use. If we can't identify it then
> + * we know it's an xM. To map the ID values please see nand_ids.c
> + */
> + identify_nand_chip(&pop_mfr, &pop_id);
> +
> + timings->mr = MICRON_V_MR_165;
> + switch (get_board_revision()) {
> + case REVISION_C4:
> + if (pop_mfr == NAND_MFR_STMICRO && pop_id == 0xba) {
> + /* 512MB DDR */
> + timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
> + timings->ctrla = NUMONYX_V_ACTIMA_165;
> + timings->ctrlb = NUMONYX_V_ACTIMB_165;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHZ;
> + break;
> + } else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xba) {
> + /* Beagleboard Rev C4, 512MB Nand/256MB DDR*/
> + timings->mcfg = MICRON_V_MCFG_165(128 << 20);
> + timings->ctrla = MICRON_V_ACTIMA_165;
> + timings->ctrlb = MICRON_V_ACTIMB_165;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHZ;
> + break;
> + } else if (pop_mfr == NAND_MFR_MICRON && pop_id == 0xbc) {
> + /* Beagleboard Rev C5, 256MB DDR */
> + timings->mcfg = MICRON_V_MCFG_200(256 << 20);
> + timings->ctrla = MICRON_V_ACTIMA_200;
> + timings->ctrlb = MICRON_V_ACTIMB_200;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHZ;
> + break;
> + }
> + case REVISION_XM_AB:
> + case REVISION_XM_C:
> + if (pop_mfr == 0) {
> + /* 256MB DDR */
> + timings->mcfg = MICRON_V_MCFG_200(256 << 20);
> + timings->ctrla = MICRON_V_ACTIMA_200;
> + timings->ctrlb = MICRON_V_ACTIMB_200;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHZ;
> + } else {
> + /* 512MB DDR */
> + timings->mcfg = NUMONYX_V_MCFG_165(512 << 20);
> + timings->ctrla = NUMONYX_V_ACTIMA_165;
> + timings->ctrlb = NUMONYX_V_ACTIMB_165;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHZ;
> + }
> + break;
> + default:
> + /* Assume 128MB and Micron/165MHz timings to be safe */
> + timings->mcfg = MICRON_V_MCFG_165(128 << 20);
> + timings->ctrla = MICRON_V_ACTIMA_165;
> + timings->ctrlb = MICRON_V_ACTIMB_165;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHZ;
> + }
> +}
> +#endif
> +
> +/*
> + * Routine: get_expansion_id
> + * Description: This function checks for expansion board by checking I2C
> + * bus 1 for the availability of an AT24C01B serial EEPROM.
> + * returns the device_vendor field from the EEPROM
> + */
> +static unsigned int get_expansion_id(void)
> +{
> +#if (IS_ENABLED(CONFIG_DM_I2C))
> + struct udevice *dev;
> + struct udevice *bus;
> + int rc;
> +
> + rc = uclass_get_device_by_seq(UCLASS_I2C, CONFIG_EEPROM_BUS_ADDRESS,
> + &bus);
> + if (rc)
> + return rc;
> + rc = dm_i2c_probe(bus, CONFIG_EEPROM_CHIP_ADDRESS, 0, &dev);
> + if (rc)
> + return rc;
> +
> + /* Read configuration data. */
> + (void)dm_i2c_read(dev, 1, (u8 *)&expansion_config,
> + sizeof(expansion_config));
> +
> + /* Retry reading configuration data with 16-bit addressing */
> + if (expansion_config.device_vendor == 0xFFFFFF00 ||
> + expansion_config.device_vendor == 0xFFFFFFFF) {
> + printf("EEPROM may be blank, retrying with 16-bit:\n");
> + (void)dm_i2c_read(dev, 2, (u8 *)&expansion_config,
> + sizeof(expansion_config));
> + }
> +#else
> + /* Read configuration data. */
> + i2c_read(CONFIG_EEPROM_CHIP_ADDRESS, 0, 1, (u8 *)&expansion_config,
> + sizeof(expansion_config));
> +
> + /* Retry reading configuration data with 16bit addressing. */
> + if (expansion_config.device_vendor == 0xFFFFFF00 ||
> + expansion_config.device_vendor == 0xFFFFFFFF) {
> + printf("EEPROM is blank or 8bit addressing failed: retrying
> with 16bit:\n");
> + i2c_read(CONFIG_EEPROM_CHIP_ADDRESS, 0, 2, (u8
> *)&expansion_config,
> + sizeof(expansion_config));
> + }
> +
> + i2c_set_bus_num(TWL4030_I2C_BUS);
> +#endif
> + return expansion_config.device_vendor;
> +}
> +
> +#if (IS_ENABLED(CONFIG_VIDEO_OMAP3))
> +/*
> + * Configure DSS to display background color on DVID
> + * Configure VENC to display color bar on S-Video
> + */
> +static void beagle_display_init(void)
> +{
> + omap3_dss_venc_config(&venc_config_std_tv, VENC_HEIGHT, VENC_WIDTH);
> + switch (get_board_revision()) {
> + case REVISION_AXBX:
> + case REVISION_CX:
> + case REVISION_C4:
> + omap3_dss_panel_config(&dvid_cfg);
> + break;
> + case REVISION_XM_AB:
> + case REVISION_XM_C:
> + default:
> + omap3_dss_panel_config(&dvid_cfg_xm);
> + break;
> + }
> +}
> +
> +/*
> + * Enable DVI power
> + */
> +static void beagle_dvi_pup(void)
> +{
> + uchar val;
> +
> + switch (get_board_revision()) {
> + case REVISION_AXBX:
> + case REVISION_CX:
> + case REVISION_C4:
> + gpio_request(170, "dvi");
> + gpio_direction_output(170, 0);
> + gpio_set_value(170, 1);
> + break;
> + case REVISION_XM_AB:
> + case REVISION_XM_C:
> + default:
> + #define GPIODATADIR1 (TWL4030_BASEADD_GPIO + 3)
> + #define GPIODATAOUT1 (TWL4030_BASEADD_GPIO + 6)
> +
> +#if (IS_ENABLED(CONFIG_DM_I2C))
> + struct udevice *dev;
> + struct udevice *bus;
> + int rc;
> +
> + rc = uclass_get_device_by_seq(UCLASS_I2C, TWL4030_I2C_BUS,
> + &bus);
> + if (rc)
> + return;
> + rc = dm_i2c_probe(bus, TWL4030_CHIP_GPIO, 0, &dev);
> + if (rc)
> + return;
> +
> + (void)dm_i2c_read(dev, GPIODATADIR1, &val, 1);
> + val |= 4;
> + (void)dm_i2c_write(dev, GPIODATADIR1, &val, 1);
> +
> + (void)dm_i2c_read(dev, GPIODATAOUT1, &val, 1);
> + val |= 4;
> + (void)dm_i2c_write(dev, GPIODATAOUT1, &val, 1);
> +#else
> + i2c_read(TWL4030_CHIP_GPIO, GPIODATADIR1, 1, &val, 1);
> + val |= 4;
> + i2c_write(TWL4030_CHIP_GPIO, GPIODATADIR1, 1, &val, 1);
> +
> + i2c_read(TWL4030_CHIP_GPIO, GPIODATAOUT1, 1, &val, 1);
> + val |= 4;
> + i2c_write(TWL4030_CHIP_GPIO, GPIODATAOUT1, 1, &val, 1);
> +#endif
> + break;
> + }
> +}
> +#endif
> +
> +/*
> + * Routine: misc_init_r
> + * Description: Configure board specific parts
> + */
> +int misc_init_r(void)
> +{
> + struct gpio *gpio5_base = (struct gpio *)OMAP34XX_GPIO5_BASE;
> + struct gpio *gpio6_base = (struct gpio *)OMAP34XX_GPIO6_BASE;
> + struct control_prog_io *prog_io_base = (struct control_prog_io
> *)OMAP34XX_CTRL_BASE;
> + bool generate_fake_mac = false;
> + u32 value;
> +
> + /* Enable i2c2 pullup resisters */
> + value = readl(&prog_io_base->io1);
> + value &= ~(PRG_I2C2_PULLUPRESX);
> + writel(value, &prog_io_base->io1);
> +
> + switch (get_board_revision()) {
> + case REVISION_AXBX:
> + printf("Beagle Rev Ax/Bx\n");
> + env_set("beaglerev", "AxBx");
> + break;
> + case REVISION_CX:
> + printf("Beagle Rev C1/C2/C3\n");
> + env_set("beaglerev", "Cx");
> + MUX_BEAGLE_C();
> + break;
> + case REVISION_C4:
> + printf("Beagle Rev C4\n");
> + env_set("beaglerev", "C4");
> + MUX_BEAGLE_C();
> + /* Set VAUX2 to 1.8V for EHCI PHY */
> + twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
> + TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
> + TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
> + TWL4030_PM_RECEIVER_DEV_GRP_P1);
> + break;
> + case REVISION_XM_AB:
> + printf("Beagle xM Rev A/B\n");
> + env_set("beaglerev", "xMAB");
> + MUX_BEAGLE_XM();
> + /* Set VAUX2 to 1.8V for EHCI PHY */
> + twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
> + TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
> + TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
> + TWL4030_PM_RECEIVER_DEV_GRP_P1);
> + generate_fake_mac = true;
> + break;
> + case REVISION_XM_C:
> + printf("Beagle xM Rev C\n");
> + env_set("beaglerev", "xMC");
> + MUX_BEAGLE_XM();
> + /* Set VAUX2 to 1.8V for EHCI PHY */
> + twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
> + TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
> + TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
> + TWL4030_PM_RECEIVER_DEV_GRP_P1);
> + generate_fake_mac = true;
> + break;
> + default:
> + printf("Beagle unknown 0x%02x\n", get_board_revision());
> + MUX_BEAGLE_XM();
> + /* Set VAUX2 to 1.8V for EHCI PHY */
> + twl4030_pmrecv_vsel_cfg(TWL4030_PM_RECEIVER_VAUX2_DEDICATED,
> + TWL4030_PM_RECEIVER_VAUX2_VSEL_18,
> + TWL4030_PM_RECEIVER_VAUX2_DEV_GRP,
> + TWL4030_PM_RECEIVER_DEV_GRP_P1);
> + generate_fake_mac = true;
> + }
> +
> + switch (get_expansion_id()) {
> + case TINCANTOOLS_ZIPPY:
> + printf("Recognized Tincantools Zippy board (rev %d %s)\n",
> + expansion_config.revision,
> + expansion_config.fab_revision);
> + MUX_TINCANTOOLS_ZIPPY();
> + env_set("buddy", "zippy");
> + break;
> + case TINCANTOOLS_ZIPPY2:
> + printf("Recognized Tincantools Zippy2 board (rev %d %s)\n",
> + expansion_config.revision,
> + expansion_config.fab_revision);
> + MUX_TINCANTOOLS_ZIPPY();
> + env_set("buddy", "zippy2");
> + break;
> + case TINCANTOOLS_TRAINER:
> + printf("Recognized Tincantools Trainer board (rev %d %s)\n",
> + expansion_config.revision,
> + expansion_config.fab_revision);
> + MUX_TINCANTOOLS_ZIPPY();
> + MUX_TINCANTOOLS_TRAINER();
> + env_set("buddy", "trainer");
> + break;
> + case TINCANTOOLS_SHOWDOG:
> + printf("Recognized Tincantools Showdow board (rev %d %s)\n",
> + expansion_config.revision,
> + expansion_config.fab_revision);
> + /* Place holder for DSS2 definition for showdog lcd */
> + env_set("defaultdisplay", "showdoglcd");
> + env_set("buddy", "showdog");
> + break;
> + case KBADC_BEAGLEFPGA:
> + printf("Recognized KBADC Beagle FPGA board\n");
> + MUX_KBADC_BEAGLEFPGA();
> + env_set("buddy", "beaglefpga");
> + break;
> + case LW_BEAGLETOUCH:
> + printf("Recognized Liquidware BeagleTouch board\n");
> + env_set("buddy", "beagletouch");
> + break;
> + case BRAINMUX_LCDOG:
> + printf("Recognized Brainmux LCDog board\n");
> + env_set("buddy", "lcdog");
> + break;
> + case BRAINMUX_LCDOGTOUCH:
> + printf("Recognized Brainmux LCDog Touch board\n");
> + env_set("buddy", "lcdogtouch");
> + break;
> + case BBTOYS_WIFI:
> + printf("Recognized BeagleBoardToys WiFi board\n");
> + MUX_BBTOYS_WIFI()
> + env_set("buddy", "bbtoys-wifi");
> + break;
> + case BBTOYS_VGA:
> + printf("Recognized BeagleBoardToys VGA board\n");
> + break;
> + case BBTOYS_LCD:
> + printf("Recognized BeagleBoardToys LCD board\n");
> + break;
> + case BCT_BRETTL3:
> + printf("Recognized bct electronic GmbH brettl3 board\n");
> + break;
> + case BCT_BRETTL4:
> + printf("Recognized bct electronic GmbH brettl4 board\n");
> + break;
> + case LSR_COM6L_ADPT:
> + printf("Recognized LSR COM6L Adapter Board\n");
> + MUX_BBTOYS_WIFI()
> + env_set("buddy", "lsr-com6l-adpt");
> + break;
> + case BEAGLE_NO_EEPROM:
> + printf("No EEPROM on expansion board\n");
> + env_set("buddy", "none");
> + break;
> + default:
> + printf("Unrecognized expansion board: %x\n",
> + expansion_config.device_vendor);
> + env_set("buddy", "unknown");
> + }
> +
> + if (expansion_config.content == 1)
> + env_set(expansion_config.env_var, expansion_config.env_setting);
> +
> + twl4030_power_init();
> + twl4030_power_mmc_init(0);
> +
> + switch (get_board_revision()) {
> + case REVISION_XM_AB:
> + twl4030_led_init(TWL4030_LED_LEDEN_LEDBON);
> + break;
> + default:
> + twl4030_led_init(TWL4030_LED_LEDEN_LEDAON |
> TWL4030_LED_LEDEN_LEDBON);
> + break;
> + }
> +
> + /* Set GPIO states before they are made outputs */
> + writel(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1,
> + &gpio6_base->setdataout);
> + writel(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
> + GPIO15 | GPIO14 | GPIO13 | GPIO12, &gpio5_base->setdataout);
> +
> + /* Configure GPIOs to output */
> + writel(~(GPIO23 | GPIO10 | GPIO8 | GPIO2 | GPIO1), &gpio6_base->oe);
> + writel(~(GPIO31 | GPIO30 | GPIO29 | GPIO28 | GPIO22 | GPIO21 |
> + GPIO15 | GPIO14 | GPIO13 | GPIO12), &gpio5_base->oe);
> +
> + omap_die_id_display();
> +
> +#if (IS_ENABLED(CONFIG_VIDEO_OMAP3))
> + beagle_dvi_pup();
> + beagle_display_init();
> + omap3_dss_enable();
> +#endif
> +
> + if (generate_fake_mac)
> + omap_die_id_usbethaddr();
> +
> +#if defined(CONFIG_MTDIDS_DEFAULT) && defined(CONFIG_MTDPARTS_DEFAULT)
> + if (strlen(CONFIG_MTDIDS_DEFAULT))
> + env_set("mtdids", CONFIG_MTDIDS_DEFAULT);
> +
> + if (strlen(CONFIG_MTDPARTS_DEFAULT))
> + env_set("mtdparts", CONFIG_MTDPARTS_DEFAULT);
> +#endif
> +
> + return 0;
> +}
> +
> +/*
> + * Routine: set_muxconf_regs
> + * Description: Setting up the configuration Mux registers specific to the
> + * hardware. Many pins need to be moved from protect to primary
> + * mode.
> + */
> +void set_muxconf_regs(void)
> +{
> + /* Convert to be like am335x/mux.c file. */
> + MUX_BEAGLE();
> +}
> diff --git a/board/beagle/beagle/beagle.h b/board/beagle/beagle/beagle.h
> new file mode 100644
> index 00000000000..ce78ea661b9
> --- /dev/null
> +++ b/board/beagle/beagle/beagle.h
> @@ -0,0 +1,545 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * (C) Copyright 2008
> + * Dirk Behme <dirk.be...@gmail.com>
> + */
> +#ifndef _BEAGLE_H_
> +#define _BEAGLE_H_
> +
> +#include <asm/arch/dss.h>
> +
> +const omap3_sysinfo sysinfo = {
> + DDR_STACKED,
> + "OMAP3 Beagle board",
> +#if defined(CONFIG_ENV_IS_IN_ONENAND)
> + "OneNAND",
> +#else
> + "NAND",
> +#endif
> +};
> +
> +/* BeagleBoard revisions */
> +#define REVISION_AXBX 0x7
> +#define REVISION_CX 0x6
> +#define REVISION_C4 0x5
> +#define REVISION_XM_AB 0x0
> +#define REVISION_XM_C 0x2
> +
> +/*
> + * IEN - Input Enable
> + * IDIS - Input Disable
> + * PTD - Pull type Down
> + * PTU - Pull type Up
> + * DIS - Pull type selection is inactive
> + * EN - Pull type selection is active
> + * M0 - Mode 0
> + * The commented string gives the final mux configuration for that pin
> + */
> +#define MUX_BEAGLE() \
> + /*SDRC*/\
> + MUX_VAL(CP(SDRC_D0), (IEN | PTD | DIS | M0)) /*SDRC_D0*/\
> + MUX_VAL(CP(SDRC_D1), (IEN | PTD | DIS | M0)) /*SDRC_D1*/\
> + MUX_VAL(CP(SDRC_D2), (IEN | PTD | DIS | M0)) /*SDRC_D2*/\
> + MUX_VAL(CP(SDRC_D3), (IEN | PTD | DIS | M0)) /*SDRC_D3*/\
> + MUX_VAL(CP(SDRC_D4), (IEN | PTD | DIS | M0)) /*SDRC_D4*/\
> + MUX_VAL(CP(SDRC_D5), (IEN | PTD | DIS | M0)) /*SDRC_D5*/\
> + MUX_VAL(CP(SDRC_D6), (IEN | PTD | DIS | M0)) /*SDRC_D6*/\
> + MUX_VAL(CP(SDRC_D7), (IEN | PTD | DIS | M0)) /*SDRC_D7*/\
> + MUX_VAL(CP(SDRC_D8), (IEN | PTD | DIS | M0)) /*SDRC_D8*/\
> + MUX_VAL(CP(SDRC_D9), (IEN | PTD | DIS | M0)) /*SDRC_D9*/\
> + MUX_VAL(CP(SDRC_D10), (IEN | PTD | DIS | M0)) /*SDRC_D10*/\
> + MUX_VAL(CP(SDRC_D11), (IEN | PTD | DIS | M0)) /*SDRC_D11*/\
> + MUX_VAL(CP(SDRC_D12), (IEN | PTD | DIS | M0)) /*SDRC_D12*/\
> + MUX_VAL(CP(SDRC_D13), (IEN | PTD | DIS | M0)) /*SDRC_D13*/\
> + MUX_VAL(CP(SDRC_D14), (IEN | PTD | DIS | M0)) /*SDRC_D14*/\
> + MUX_VAL(CP(SDRC_D15), (IEN | PTD | DIS | M0)) /*SDRC_D15*/\
> + MUX_VAL(CP(SDRC_D16), (IEN | PTD | DIS | M0)) /*SDRC_D16*/\
> + MUX_VAL(CP(SDRC_D17), (IEN | PTD | DIS | M0)) /*SDRC_D17*/\
> + MUX_VAL(CP(SDRC_D18), (IEN | PTD | DIS | M0)) /*SDRC_D18*/\
> + MUX_VAL(CP(SDRC_D19), (IEN | PTD | DIS | M0)) /*SDRC_D19*/\
> + MUX_VAL(CP(SDRC_D20), (IEN | PTD | DIS | M0)) /*SDRC_D20*/\
> + MUX_VAL(CP(SDRC_D21), (IEN | PTD | DIS | M0)) /*SDRC_D21*/\
> + MUX_VAL(CP(SDRC_D22), (IEN | PTD | DIS | M0)) /*SDRC_D22*/\
> + MUX_VAL(CP(SDRC_D23), (IEN | PTD | DIS | M0)) /*SDRC_D23*/\
> + MUX_VAL(CP(SDRC_D24), (IEN | PTD | DIS | M0)) /*SDRC_D24*/\
> + MUX_VAL(CP(SDRC_D25), (IEN | PTD | DIS | M0)) /*SDRC_D25*/\
> + MUX_VAL(CP(SDRC_D26), (IEN | PTD | DIS | M0)) /*SDRC_D26*/\
> + MUX_VAL(CP(SDRC_D27), (IEN | PTD | DIS | M0)) /*SDRC_D27*/\
> + MUX_VAL(CP(SDRC_D28), (IEN | PTD | DIS | M0)) /*SDRC_D28*/\
> + MUX_VAL(CP(SDRC_D29), (IEN | PTD | DIS | M0)) /*SDRC_D29*/\
> + MUX_VAL(CP(SDRC_D30), (IEN | PTD | DIS | M0)) /*SDRC_D30*/\
> + MUX_VAL(CP(SDRC_D31), (IEN | PTD | DIS | M0)) /*SDRC_D31*/\
> + MUX_VAL(CP(SDRC_CLK), (IEN | PTD | DIS | M0)) /*SDRC_CLK*/\
> + MUX_VAL(CP(SDRC_DQS0), (IEN | PTD | DIS | M0)) /*SDRC_DQS0*/\
> + MUX_VAL(CP(SDRC_DQS1), (IEN | PTD | DIS | M0)) /*SDRC_DQS1*/\
> + MUX_VAL(CP(SDRC_DQS2), (IEN | PTD | DIS | M0)) /*SDRC_DQS2*/\
> + MUX_VAL(CP(SDRC_DQS3), (IEN | PTD | DIS | M0)) /*SDRC_DQS3*/\
> + /*GPMC*/\
> + MUX_VAL(CP(GPMC_A1), (IDIS | PTD | DIS | M0)) /*GPMC_A1*/\
> + MUX_VAL(CP(GPMC_A2), (IDIS | PTD | DIS | M0)) /*GPMC_A2*/\
> + MUX_VAL(CP(GPMC_A3), (IDIS | PTD | DIS | M0)) /*GPMC_A3*/\
> + MUX_VAL(CP(GPMC_A4), (IDIS | PTD | DIS | M0)) /*GPMC_A4*/\
> + MUX_VAL(CP(GPMC_A5), (IDIS | PTD | DIS | M0)) /*GPMC_A5*/\
> + MUX_VAL(CP(GPMC_A6), (IDIS | PTD | DIS | M0)) /*GPMC_A6*/\
> + MUX_VAL(CP(GPMC_A7), (IDIS | PTD | DIS | M0)) /*GPMC_A7*/\
> + MUX_VAL(CP(GPMC_A8), (IDIS | PTD | DIS | M0)) /*GPMC_A8*/\
> + MUX_VAL(CP(GPMC_A9), (IDIS | PTD | DIS | M0)) /*GPMC_A9*/\
> + MUX_VAL(CP(GPMC_A10), (IDIS | PTD | DIS | M0)) /*GPMC_A10*/\
> + MUX_VAL(CP(GPMC_D0), (IEN | PTD | DIS | M0)) /*GPMC_D0*/\
> + MUX_VAL(CP(GPMC_D1), (IEN | PTD | DIS | M0)) /*GPMC_D1*/\
> + MUX_VAL(CP(GPMC_D2), (IEN | PTD | DIS | M0)) /*GPMC_D2*/\
> + MUX_VAL(CP(GPMC_D3), (IEN | PTD | DIS | M0)) /*GPMC_D3*/\
> + MUX_VAL(CP(GPMC_D4), (IEN | PTD | DIS | M0)) /*GPMC_D4*/\
> + MUX_VAL(CP(GPMC_D5), (IEN | PTD | DIS | M0)) /*GPMC_D5*/\
> + MUX_VAL(CP(GPMC_D6), (IEN | PTD | DIS | M0)) /*GPMC_D6*/\
> + MUX_VAL(CP(GPMC_D7), (IEN | PTD | DIS | M0)) /*GPMC_D7*/\
> + MUX_VAL(CP(GPMC_D8), (IEN | PTD | DIS | M0)) /*GPMC_D8*/\
> + MUX_VAL(CP(GPMC_D9), (IEN | PTD | DIS | M0)) /*GPMC_D9*/\
> + MUX_VAL(CP(GPMC_D10), (IEN | PTD | DIS | M0)) /*GPMC_D10*/\
> + MUX_VAL(CP(GPMC_D11), (IEN | PTD | DIS | M0)) /*GPMC_D11*/\
> + MUX_VAL(CP(GPMC_D12), (IEN | PTD | DIS | M0)) /*GPMC_D12*/\
> + MUX_VAL(CP(GPMC_D13), (IEN | PTD | DIS | M0)) /*GPMC_D13*/\
> + MUX_VAL(CP(GPMC_D14), (IEN | PTD | DIS | M0)) /*GPMC_D14*/\
> + MUX_VAL(CP(GPMC_D15), (IEN | PTD | DIS | M0)) /*GPMC_D15*/\
> + MUX_VAL(CP(GPMC_NCS0), (IDIS | PTU | EN | M0)) /*GPMC_nCS0*/\
> + MUX_VAL(CP(GPMC_NCS1), (IDIS | PTU | EN | M0)) /*GPMC_nCS1*/\
> + MUX_VAL(CP(GPMC_NCS2), (IDIS | PTU | EN | M0)) /*GPMC_nCS2*/\
> + MUX_VAL(CP(GPMC_NCS3), (IDIS | PTU | EN | M0)) /*GPMC_nCS3*/\
> + MUX_VAL(CP(GPMC_NCS4), (IDIS | PTU | EN | M0)) /*GPMC_nCS4*/\
> + MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | DIS | M0)) /*GPMC_nCS5*/\
> + MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M1))
> /*SYS_nDMA_REQ2*/\
> + MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M1))
> /*SYS_nDMA_REQ3*/\
> + MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /*GPMC_nBE1*/\
> + MUX_VAL(CP(GPMC_WAIT2), (IEN | PTU | EN | M0)) /*GPMC_WAIT2*/\
> + MUX_VAL(CP(GPMC_WAIT3), (IEN | PTU | EN | M0)) /*GPMC_WAIT3*/\
> + MUX_VAL(CP(GPMC_CLK), (IDIS | PTD | DIS | M0)) /*GPMC_CLK*/\
> + MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0))
> /*GPMC_nADV_ALE*/\
> + MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\
> + MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\
> + MUX_VAL(CP(GPMC_NBE0_CLE), (IDIS | PTD | DIS | M0))
> /*GPMC_nBE0_CLE*/\
> + MUX_VAL(CP(GPMC_NWP), (IEN | PTD | DIS | M0)) /*GPMC_nWP*/\
> + MUX_VAL(CP(GPMC_WAIT0), (IEN | PTU | EN | M0)) /*GPMC_WAIT0*/\
> + MUX_VAL(CP(GPMC_WAIT1), (IEN | PTU | EN | M0)) /*GPMC_WAIT1*/\
> + /*DSS*/\
> + MUX_VAL(CP(DSS_PCLK), (IDIS | PTD | DIS | M0)) /*DSS_PCLK*/\
> + MUX_VAL(CP(DSS_HSYNC), (IDIS | PTD | DIS | M0)) /*DSS_HSYNC*/\
> + MUX_VAL(CP(DSS_VSYNC), (IDIS | PTD | DIS | M0)) /*DSS_VSYNC*/\
> + MUX_VAL(CP(DSS_ACBIAS), (IDIS | PTD | DIS | M0)) /*DSS_ACBIAS*/\
> + MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M0)) /*DSS_DATA0*/\
> + MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M0)) /*DSS_DATA1*/\
> + MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M0)) /*DSS_DATA2*/\
> + MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M0)) /*DSS_DATA3*/\
> + MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M0)) /*DSS_DATA4*/\
> + MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M0)) /*DSS_DATA5*/\
> + MUX_VAL(CP(DSS_DATA6), (IDIS | PTD | DIS | M0)) /*DSS_DATA6*/\
> + MUX_VAL(CP(DSS_DATA7), (IDIS | PTD | DIS | M0)) /*DSS_DATA7*/\
> + MUX_VAL(CP(DSS_DATA8), (IDIS | PTD | DIS | M0)) /*DSS_DATA8*/\
> + MUX_VAL(CP(DSS_DATA9), (IDIS | PTD | DIS | M0)) /*DSS_DATA9*/\
> + MUX_VAL(CP(DSS_DATA10), (IDIS | PTD | DIS | M0)) /*DSS_DATA10*/\
> + MUX_VAL(CP(DSS_DATA11), (IDIS | PTD | DIS | M0)) /*DSS_DATA11*/\
> + MUX_VAL(CP(DSS_DATA12), (IDIS | PTD | DIS | M0)) /*DSS_DATA12*/\
> + MUX_VAL(CP(DSS_DATA13), (IDIS | PTD | DIS | M0)) /*DSS_DATA13*/\
> + MUX_VAL(CP(DSS_DATA14), (IDIS | PTD | DIS | M0)) /*DSS_DATA14*/\
> + MUX_VAL(CP(DSS_DATA15), (IDIS | PTD | DIS | M0)) /*DSS_DATA15*/\
> + MUX_VAL(CP(DSS_DATA16), (IDIS | PTD | DIS | M0)) /*DSS_DATA16*/\
> + MUX_VAL(CP(DSS_DATA17), (IDIS | PTD | DIS | M0)) /*DSS_DATA17*/\
> + MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M0)) /*DSS_DATA18*/\
> + MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M0)) /*DSS_DATA19*/\
> + MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M0)) /*DSS_DATA20*/\
> + MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M0)) /*DSS_DATA21*/\
> + MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M0)) /*DSS_DATA22*/\
> + MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M0)) /*DSS_DATA23*/\
> + /*CAMERA*/\
> + MUX_VAL(CP(CAM_HS), (IEN | PTU | EN | M0)) /*CAM_HS */\
> + MUX_VAL(CP(CAM_VS), (IEN | PTU | EN | M0)) /*CAM_VS */\
> + MUX_VAL(CP(CAM_XCLKA), (IDIS | PTD | DIS | M0)) /*CAM_XCLKA*/\
> + MUX_VAL(CP(CAM_PCLK), (IEN | PTU | EN | M0)) /*CAM_PCLK*/\
> + MUX_VAL(CP(CAM_FLD), (IDIS | PTD | DIS | M4)) /*GPIO_98*/\
> + MUX_VAL(CP(CAM_D0), (IEN | PTD | DIS | M0)) /*CAM_D0*/\
> + MUX_VAL(CP(CAM_D1), (IEN | PTD | DIS | M0)) /*CAM_D1*/\
> + MUX_VAL(CP(CAM_D2), (IEN | PTD | DIS | M0)) /*CAM_D2*/\
> + MUX_VAL(CP(CAM_D3), (IEN | PTD | DIS | M0)) /*CAM_D3*/\
> + MUX_VAL(CP(CAM_D4), (IEN | PTD | DIS | M0)) /*CAM_D4*/\
> + MUX_VAL(CP(CAM_D5), (IEN | PTD | DIS | M0)) /*CAM_D5*/\
> + MUX_VAL(CP(CAM_D6), (IEN | PTD | DIS | M0)) /*CAM_D6*/\
> + MUX_VAL(CP(CAM_D7), (IEN | PTD | DIS | M0)) /*CAM_D7*/\
> + MUX_VAL(CP(CAM_D8), (IEN | PTD | DIS | M0)) /*CAM_D8*/\
> + MUX_VAL(CP(CAM_D9), (IEN | PTD | DIS | M0)) /*CAM_D9*/\
> + MUX_VAL(CP(CAM_D10), (IEN | PTD | DIS | M0)) /*CAM_D10*/\
> + MUX_VAL(CP(CAM_D11), (IEN | PTD | DIS | M0)) /*CAM_D11*/\
> + MUX_VAL(CP(CAM_XCLKB), (IDIS | PTD | DIS | M0)) /*CAM_XCLKB*/\
> + MUX_VAL(CP(CAM_WEN), (IEN | PTD | DIS | M4)) /*GPIO_167*/\
> + MUX_VAL(CP(CAM_STROBE), (IDIS | PTD | DIS | M0)) /*CAM_STROBE*/\
> + MUX_VAL(CP(CSI2_DX0), (IEN | PTD | DIS | M0)) /*CSI2_DX0*/\
> + MUX_VAL(CP(CSI2_DY0), (IEN | PTD | DIS | M0)) /*CSI2_DY0*/\
> + MUX_VAL(CP(CSI2_DX1), (IEN | PTD | DIS | M0)) /*CSI2_DX1*/\
> + MUX_VAL(CP(CSI2_DY1), (IEN | PTD | DIS | M0)) /*CSI2_DY1*/\
> + /*Audio Interface */\
> + MUX_VAL(CP(MCBSP2_FSX), (IEN | PTD | DIS | M0)) /*McBSP2_FSX*/\
> + MUX_VAL(CP(MCBSP2_CLKX), (IEN | PTD | DIS | M0))
> /*McBSP2_CLKX*/\
> + MUX_VAL(CP(MCBSP2_DR), (IEN | PTD | DIS | M0)) /*McBSP2_DR*/\
> + MUX_VAL(CP(MCBSP2_DX), (IDIS | PTD | DIS | M0)) /*McBSP2_DX*/\
> + /*Expansion card */\
> + MUX_VAL(CP(MMC1_CLK), (IDIS | PTU | EN | M0)) /*MMC1_CLK*/\
> + MUX_VAL(CP(MMC1_CMD), (IEN | PTU | EN | M0)) /*MMC1_CMD*/\
> + MUX_VAL(CP(MMC1_DAT0), (IEN | PTU | EN | M0)) /*MMC1_DAT0*/\
> + MUX_VAL(CP(MMC1_DAT1), (IEN | PTU | EN | M0)) /*MMC1_DAT1*/\
> + MUX_VAL(CP(MMC1_DAT2), (IEN | PTU | EN | M0)) /*MMC1_DAT2*/\
> + MUX_VAL(CP(MMC1_DAT3), (IEN | PTU | EN | M0)) /*MMC1_DAT3*/\
> + MUX_VAL(CP(MMC1_DAT4), (IEN | PTU | EN | M0)) /*MMC1_DAT4*/\
> + MUX_VAL(CP(MMC1_DAT5), (IEN | PTU | EN | M0)) /*MMC1_DAT5*/\
> + MUX_VAL(CP(MMC1_DAT6), (IEN | PTU | EN | M0)) /*MMC1_DAT6*/\
> + MUX_VAL(CP(MMC1_DAT7), (IEN | PTU | EN | M0)) /*MMC1_DAT7*/\
> + /*Wireless LAN */\
> + MUX_VAL(CP(MMC2_CLK), (IEN | PTU | EN | M4)) /*GPIO_130*/\
> + MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M4)) /*GPIO_131*/\
> + MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M4)) /*GPIO_132*/\
> + MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M4)) /*GPIO_133*/\
> + MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M4)) /*GPIO_134*/\
> + MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M4)) /*GPIO_135*/\
> + MUX_VAL(CP(MMC2_DAT4), (IEN | PTU | EN | M4)) /*GPIO_136*/\
> + MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M4)) /*GPIO_137*/\
> + MUX_VAL(CP(MMC2_DAT6), (IEN | PTU | EN | M4)) /*GPIO_138*/\
> + MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M4)) /*GPIO_139*/\
> + /*Bluetooth*/\
> + MUX_VAL(CP(MCBSP3_DX), (IEN | PTD | DIS | M1)) /*UART2_CTS*/\
> + MUX_VAL(CP(MCBSP3_DR), (IDIS | PTD | DIS | M1)) /*UART2_RTS*/\
> + MUX_VAL(CP(MCBSP3_CLKX), (IDIS | PTD | DIS | M1)) /*UART2_TX*/\
> + MUX_VAL(CP(MCBSP3_FSX), (IEN | PTD | DIS | M1)) /*UART2_RX*/\
> + MUX_VAL(CP(UART2_CTS), (IEN | PTD | DIS | M4)) /*GPIO_144*/\
> + MUX_VAL(CP(UART2_RTS), (IEN | PTD | DIS | M4)) /*GPIO_145*/\
> + MUX_VAL(CP(UART2_TX), (IEN | PTD | DIS | M4)) /*GPIO_146*/\
> + MUX_VAL(CP(UART2_RX), (IEN | PTD | DIS | M4)) /*GPIO_147*/\
> + /*Modem Interface */\
> + MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M0)) /*UART1_TX*/\
> + MUX_VAL(CP(UART1_RTS), (IDIS | PTD | DIS | M4)) /*GPIO_149*/ \
> + MUX_VAL(CP(UART1_CTS), (IDIS | PTD | DIS | M4)) /*GPIO_150*/ \
> + MUX_VAL(CP(UART1_RX), (IEN | PTD | DIS | M0)) /*UART1_RX*/\
> + MUX_VAL(CP(MCBSP4_CLKX), (IEN | PTD | DIS | M1))
> /*SSI1_DAT_RX*/\
> + MUX_VAL(CP(MCBSP4_DR), (IEN | PTD | DIS | M1))
> /*SSI1_FLAG_RX*/\
> + MUX_VAL(CP(MCBSP4_DX), (IEN | PTD | DIS | M1))
> /*SSI1_RDY_RX*/\
> + MUX_VAL(CP(MCBSP4_FSX), (IEN | PTD | DIS | M1)) /*SSI1_WAKE*/\
> + MUX_VAL(CP(MCBSP1_CLKR), (IDIS | PTD | DIS | M4)) /*GPIO_156*/\
> + MUX_VAL(CP(MCBSP1_FSR), (IDIS | PTU | EN | M4)) /*GPIO_157*/\
> + MUX_VAL(CP(MCBSP1_DX), (IDIS | PTD | DIS | M4)) /*GPIO_158*/\
> + MUX_VAL(CP(MCBSP1_DR), (IDIS | PTD | DIS | M4)) /*GPIO_159*/\
> + MUX_VAL(CP(MCBSP_CLKS), (IEN | PTU | DIS | M0)) /*McBSP_CLKS*/\
> + MUX_VAL(CP(MCBSP1_FSX), (IDIS | PTD | DIS | M4)) /*GPIO_161*/\
> + MUX_VAL(CP(MCBSP1_CLKX), (IDIS | PTD | DIS | M4)) /*GPIO_162*/\
> + /*Serial Interface*/\
> + MUX_VAL(CP(UART3_CTS_RCTX), (IEN | PTD | EN | M0))
> /*UART3_CTS_RCTX*/\
> + MUX_VAL(CP(UART3_RTS_SD), (IDIS | PTD | DIS | M0)) /*UART3_RTS_SD
> */\
> + MUX_VAL(CP(UART3_RX_IRRX), (IEN | PTD | DIS | M0))
> /*UART3_RX_IRRX*/\
> + MUX_VAL(CP(UART3_TX_IRTX), (IDIS | PTD | DIS | M0))
> /*UART3_TX_IRTX*/\
> + MUX_VAL(CP(HSUSB0_CLK), (IEN | PTD | DIS | M0)) /*HSUSB0_CLK*/\
> + MUX_VAL(CP(HSUSB0_STP), (IDIS | PTU | EN | M0)) /*HSUSB0_STP*/\
> + MUX_VAL(CP(HSUSB0_DIR), (IEN | PTD | DIS | M0)) /*HSUSB0_DIR*/\
> + MUX_VAL(CP(HSUSB0_NXT), (IEN | PTD | DIS | M0)) /*HSUSB0_NXT*/\
> + MUX_VAL(CP(HSUSB0_DATA0), (IEN | PTD | DIS | M0))
> /*HSUSB0_DATA0*/\
> + MUX_VAL(CP(HSUSB0_DATA1), (IEN | PTD | DIS | M0))
> /*HSUSB0_DATA1*/\
> + MUX_VAL(CP(HSUSB0_DATA2), (IEN | PTD | DIS | M0))
> /*HSUSB0_DATA2*/\
> + MUX_VAL(CP(HSUSB0_DATA3), (IEN | PTD | DIS | M0))
> /*HSUSB0_DATA3*/\
> + MUX_VAL(CP(HSUSB0_DATA4), (IEN | PTD | DIS | M0))
> /*HSUSB0_DATA4*/\
> + MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0))
> /*HSUSB0_DATA5*/\
> + MUX_VAL(CP(HSUSB0_DATA6), (IEN | PTD | DIS | M0))
> /*HSUSB0_DATA6*/\
> + MUX_VAL(CP(HSUSB0_DATA7), (IEN | PTD | DIS | M0))
> /*HSUSB0_DATA7*/\
> + MUX_VAL(CP(I2C1_SCL), (IEN | PTU | EN | M0)) /*I2C1_SCL*/\
> + MUX_VAL(CP(I2C1_SDA), (IEN | PTU | EN | M0)) /*I2C1_SDA*/\
> + MUX_VAL(CP(I2C2_SCL), (IEN | PTU | EN | M0)) /*I2C2_SCL*/\
> + MUX_VAL(CP(I2C2_SDA), (IEN | PTU | EN | M0)) /*I2C2_SDA*/\
> + MUX_VAL(CP(I2C3_SCL), (IEN | PTU | EN | M0)) /*I2C3_SCL*/\
> + MUX_VAL(CP(I2C3_SDA), (IEN | PTU | EN | M0)) /*I2C3_SDA*/\
> + MUX_VAL(CP(I2C4_SCL), (IEN | PTU | EN | M0)) /*I2C4_SCL*/\
> + MUX_VAL(CP(I2C4_SDA), (IEN | PTU | EN | M0)) /*I2C4_SDA*/\
> + MUX_VAL(CP(HDQ_SIO), (IDIS | PTU | EN | M4)) /*GPIO_170*/\
> + MUX_VAL(CP(MCSPI1_CLK), (IEN | PTU | EN | M4)) /*GPIO_171*/\
> + MUX_VAL(CP(MCSPI1_SIMO), (IEN | PTU | EN | M4)) /*GPIO_172*/\
> + MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTU | EN | M4)) /*GPIO_173*/\
> + MUX_VAL(CP(MCSPI1_CS0), (IEN | PTD | EN | M0)) /*McSPI1_CS0*/\
> + MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M0)) /*McSPI1_CS1*/\
> + MUX_VAL(CP(MCSPI1_CS2), (IDIS | PTD | DIS | M4)) /*GPIO_176*/\
> + /* USB EHCI (port 2) */\
> + MUX_VAL(CP(MCSPI1_CS3), (IEN | PTD | EN | M3))
> /*HSUSB2_DATA2*/\
> + MUX_VAL(CP(MCSPI2_CLK), (IEN | PTD | EN | M3))
> /*HSUSB2_DATA7*/\
> + MUX_VAL(CP(MCSPI2_SIMO), (IEN | PTD | EN | M3))
> /*HSUSB2_DATA4*/\
> + MUX_VAL(CP(MCSPI2_SOMI), (IEN | PTD | EN | M3))
> /*HSUSB2_DATA5*/\
> + MUX_VAL(CP(MCSPI2_CS0), (IEN | PTD | EN | M3))
> /*HSUSB2_DATA6*/\
> + MUX_VAL(CP(MCSPI2_CS1), (IEN | PTD | EN | M3))
> /*HSUSB2_DATA3*/\
> + MUX_VAL(CP(ETK_D10_ES2), (IDIS | PTD | DIS | M3)) /*HSUSB2_CLK*/\
> + MUX_VAL(CP(ETK_D11_ES2), (IDIS | PTD | DIS | M3)) /*HSUSB2_STP*/\
> + MUX_VAL(CP(ETK_D12_ES2), (IEN | PTD | EN | M3)) /*HSUSB2_DIR*/\
> + MUX_VAL(CP(ETK_D13_ES2), (IEN | PTD | EN | M3)) /*HSUSB2_NXT*/\
> + MUX_VAL(CP(ETK_D14_ES2), (IEN | PTD | EN | M3))
> /*HSUSB2_DATA0*/\
> + MUX_VAL(CP(ETK_D15_ES2), (IEN | PTD | EN | M3))
> /*HSUSB2_DATA1*/\
> + /*Control and debug */\
> + MUX_VAL(CP(SYS_32K), (IEN | PTD | DIS | M0)) /*SYS_32K*/\
> + MUX_VAL(CP(SYS_CLKREQ), (IEN | PTD | DIS | M0)) /*SYS_CLKREQ*/\
> + MUX_VAL(CP(SYS_NIRQ), (IEN | PTU | EN | M0)) /*SYS_nIRQ*/\
> + MUX_VAL(CP(SYS_BOOT0), (IEN | PTD | DIS | M4)) /*GPIO_2*/\
> + MUX_VAL(CP(SYS_BOOT1), (IEN | PTD | DIS | M4)) /*GPIO_3*/\
> + MUX_VAL(CP(SYS_BOOT2), (IEN | PTD | DIS | M4)) /*GPIO_4 -
> MMC1_WP*/\
> + MUX_VAL(CP(SYS_BOOT3), (IEN | PTD | DIS | M4)) /*GPIO_5*/\
> + MUX_VAL(CP(SYS_BOOT4), (IEN | PTD | DIS | M4)) /*GPIO_6*/\
> + MUX_VAL(CP(SYS_BOOT5), (IEN | PTD | DIS | M4)) /*GPIO_7*/\
> + MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M4)) /*GPIO_8*/ \
> + MUX_VAL(CP(SYS_OFF_MODE), (IEN | PTD | DIS | M0))
> /*SYS_OFF_MODE*/\
> + MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTD | DIS | M0))
> /*SYS_CLKOUT1*/\
> + MUX_VAL(CP(SYS_CLKOUT2), (IEN | PTU | EN | M4)) /*GPIO_186*/\
> + MUX_VAL(CP(ETK_CLK_ES2), (IDIS | PTU | EN | M3)) /*HSUSB1_STP*/\
> + MUX_VAL(CP(ETK_CTL_ES2), (IDIS | PTU | DIS | M3)) /*HSUSB1_CLK*/\
> + MUX_VAL(CP(ETK_D0_ES2), (IEN | PTU | DIS | M3))
> /*HSUSB1_DATA0*/\
> + MUX_VAL(CP(ETK_D1_ES2), (IEN | PTU | DIS | M3))
> /*HSUSB1_DATA1*/\
> + MUX_VAL(CP(ETK_D2_ES2), (IEN | PTU | DIS | M3))
> /*HSUSB1_DATA2*/\
> + MUX_VAL(CP(ETK_D3_ES2), (IEN | PTU | DIS | M3))
> /*HSUSB1_DATA7*/\
> + MUX_VAL(CP(ETK_D4_ES2), (IEN | PTU | DIS | M3))
> /*HSUSB1_DATA4*/\
> + MUX_VAL(CP(ETK_D5_ES2), (IEN | PTU | DIS | M3))
> /*HSUSB1_DATA5*/\
> + MUX_VAL(CP(ETK_D6_ES2), (IEN | PTU | DIS | M3))
> /*HSUSB1_DATA6*/\
> + MUX_VAL(CP(ETK_D7_ES2), (IEN | PTU | DIS | M3))
> /*HSUSB1_DATA3*/\
> + MUX_VAL(CP(ETK_D8_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_DIR*/\
> + MUX_VAL(CP(ETK_D9_ES2), (IEN | PTU | DIS | M3)) /*HSUSB1_NXT*/\
> + MUX_VAL(CP(D2D_MCAD1), (IEN | PTD | EN | M0)) /*d2d_mcad1*/\
> + MUX_VAL(CP(D2D_MCAD2), (IEN | PTD | EN | M0)) /*d2d_mcad2*/\
> + MUX_VAL(CP(D2D_MCAD3), (IEN | PTD | EN | M0)) /*d2d_mcad3*/\
> + MUX_VAL(CP(D2D_MCAD4), (IEN | PTD | EN | M0)) /*d2d_mcad4*/\
> + MUX_VAL(CP(D2D_MCAD5), (IEN | PTD | EN | M0)) /*d2d_mcad5*/\
> + MUX_VAL(CP(D2D_MCAD6), (IEN | PTD | EN | M0)) /*d2d_mcad6*/\
> + MUX_VAL(CP(D2D_MCAD7), (IEN | PTD | EN | M0)) /*d2d_mcad7*/\
> + MUX_VAL(CP(D2D_MCAD8), (IEN | PTD | EN | M0)) /*d2d_mcad8*/\
> + MUX_VAL(CP(D2D_MCAD9), (IEN | PTD | EN | M0)) /*d2d_mcad9*/\
> + MUX_VAL(CP(D2D_MCAD10), (IEN | PTD | EN | M0)) /*d2d_mcad10*/\
> + MUX_VAL(CP(D2D_MCAD11), (IEN | PTD | EN | M0)) /*d2d_mcad11*/\
> + MUX_VAL(CP(D2D_MCAD12), (IEN | PTD | EN | M0)) /*d2d_mcad12*/\
> + MUX_VAL(CP(D2D_MCAD13), (IEN | PTD | EN | M0)) /*d2d_mcad13*/\
> + MUX_VAL(CP(D2D_MCAD14), (IEN | PTD | EN | M0)) /*d2d_mcad14*/\
> + MUX_VAL(CP(D2D_MCAD15), (IEN | PTD | EN | M0)) /*d2d_mcad15*/\
> + MUX_VAL(CP(D2D_MCAD16), (IEN | PTD | EN | M0)) /*d2d_mcad16*/\
> + MUX_VAL(CP(D2D_MCAD17), (IEN | PTD | EN | M0)) /*d2d_mcad17*/\
> + MUX_VAL(CP(D2D_MCAD18), (IEN | PTD | EN | M0)) /*d2d_mcad18*/\
> + MUX_VAL(CP(D2D_MCAD19), (IEN | PTD | EN | M0)) /*d2d_mcad19*/\
> + MUX_VAL(CP(D2D_MCAD20), (IEN | PTD | EN | M0)) /*d2d_mcad20*/\
> + MUX_VAL(CP(D2D_MCAD21), (IEN | PTD | EN | M0)) /*d2d_mcad21*/\
> + MUX_VAL(CP(D2D_MCAD22), (IEN | PTD | EN | M0)) /*d2d_mcad22*/\
> + MUX_VAL(CP(D2D_MCAD23), (IEN | PTD | EN | M0)) /*d2d_mcad23*/\
> + MUX_VAL(CP(D2D_MCAD24), (IEN | PTD | EN | M0)) /*d2d_mcad24*/\
> + MUX_VAL(CP(D2D_MCAD25), (IEN | PTD | EN | M0)) /*d2d_mcad25*/\
> + MUX_VAL(CP(D2D_MCAD26), (IEN | PTD | EN | M0)) /*d2d_mcad26*/\
> + MUX_VAL(CP(D2D_MCAD27), (IEN | PTD | EN | M0)) /*d2d_mcad27*/\
> + MUX_VAL(CP(D2D_MCAD28), (IEN | PTD | EN | M0)) /*d2d_mcad28*/\
> + MUX_VAL(CP(D2D_MCAD29), (IEN | PTD | EN | M0)) /*d2d_mcad29*/\
> + MUX_VAL(CP(D2D_MCAD30), (IEN | PTD | EN | M0)) /*d2d_mcad30*/\
> + MUX_VAL(CP(D2D_MCAD31), (IEN | PTD | EN | M0)) /*d2d_mcad31*/\
> + MUX_VAL(CP(D2D_MCAD32), (IEN | PTD | EN | M0)) /*d2d_mcad32*/\
> + MUX_VAL(CP(D2D_MCAD33), (IEN | PTD | EN | M0)) /*d2d_mcad33*/\
> + MUX_VAL(CP(D2D_MCAD34), (IEN | PTD | EN | M0)) /*d2d_mcad34*/\
> + MUX_VAL(CP(D2D_MCAD35), (IEN | PTD | EN | M0)) /*d2d_mcad35*/\
> + MUX_VAL(CP(D2D_MCAD36), (IEN | PTD | EN | M0)) /*d2d_mcad36*/\
> + MUX_VAL(CP(D2D_CLK26MI), (IEN | PTD | DIS | M0))
> /*d2d_clk26mi*/\
> + MUX_VAL(CP(D2D_NRESPWRON), (IEN | PTD | EN | M0))
> /*d2d_nrespwron*/\
> + MUX_VAL(CP(D2D_NRESWARM), (IEN | PTU | EN | M0)) /*d2d_nreswarm
> */\
> + MUX_VAL(CP(D2D_ARM9NIRQ), (IEN | PTD | DIS | M0)) /*d2d_arm9nirq
> */\
> + MUX_VAL(CP(D2D_UMA2P6FIQ), (IEN | PTD | DIS | M0))
> /*d2d_uma2p6fiq*/\
> + MUX_VAL(CP(D2D_SPINT), (IEN | PTD | EN | M0)) /*d2d_spint*/\
> + MUX_VAL(CP(D2D_FRINT), (IEN | PTD | EN | M0)) /*d2d_frint*/\
> + MUX_VAL(CP(D2D_DMAREQ0), (IEN | PTD | DIS | M0))
> /*d2d_dmareq0*/\
> + MUX_VAL(CP(D2D_DMAREQ1), (IEN | PTD | DIS | M0))
> /*d2d_dmareq1*/\
> + MUX_VAL(CP(D2D_DMAREQ2), (IEN | PTD | DIS | M0))
> /*d2d_dmareq2*/\
> + MUX_VAL(CP(D2D_DMAREQ3), (IEN | PTD | DIS | M0))
> /*d2d_dmareq3*/\
> + MUX_VAL(CP(D2D_N3GTRST), (IEN | PTD | DIS | M0))
> /*d2d_n3gtrst*/\
> + MUX_VAL(CP(D2D_N3GTDI), (IEN | PTD | DIS | M0)) /*d2d_n3gtdi*/\
> + MUX_VAL(CP(D2D_N3GTDO), (IEN | PTD | DIS | M0)) /*d2d_n3gtdo*/\
> + MUX_VAL(CP(D2D_N3GTMS), (IEN | PTD | DIS | M0)) /*d2d_n3gtms*/\
> + MUX_VAL(CP(D2D_N3GTCK), (IEN | PTD | DIS | M0)) /*d2d_n3gtck*/\
> + MUX_VAL(CP(D2D_N3GRTCK), (IEN | PTD | DIS | M0))
> /*d2d_n3grtck*/\
> + MUX_VAL(CP(D2D_MSTDBY), (IEN | PTU | EN | M0)) /*d2d_mstdby*/\
> + MUX_VAL(CP(D2D_SWAKEUP), (IEN | PTD | EN | M0))
> /*d2d_swakeup*/\
> + MUX_VAL(CP(D2D_IDLEREQ), (IEN | PTD | DIS | M0))
> /*d2d_idlereq*/\
> + MUX_VAL(CP(D2D_IDLEACK), (IEN | PTU | EN | M0))
> /*d2d_idleack*/\
> + MUX_VAL(CP(D2D_MWRITE), (IEN | PTD | DIS | M0)) /*d2d_mwrite*/\
> + MUX_VAL(CP(D2D_SWRITE), (IEN | PTD | DIS | M0)) /*d2d_swrite*/\
> + MUX_VAL(CP(D2D_MREAD), (IEN | PTD | DIS | M0)) /*d2d_mread*/\
> + MUX_VAL(CP(D2D_SREAD), (IEN | PTD | DIS | M0)) /*d2d_sread*/\
> + MUX_VAL(CP(D2D_MBUSFLAG), (IEN | PTD | DIS | M0))
> /*d2d_mbusflag*/\
> + MUX_VAL(CP(D2D_SBUSFLAG), (IEN | PTD | DIS | M0))
> /*d2d_sbusflag*/\
> + MUX_VAL(CP(SDRC_CKE0), (IDIS | PTU | EN | M0)) /*sdrc_cke0*/\
> + MUX_VAL(CP(SDRC_CKE1), (IDIS | PTU | EN | M0)) /*sdrc_cke1*/
> +
> +#define MUX_BEAGLE_C() \
> + MUX_VAL(CP(MCBSP3_DX), (IEN | PTD | DIS | M4)) /*GPIO_140*/\
> + MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M4)) /*GPIO_142*/\
> + MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M4)) /*GPIO_141*/\
> + MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) /*UART2_CTS*/\
> + MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) /*UART2_RTS*/\
> + MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) /*UART2_TX*/\
> + MUX_VAL(CP(UART2_RX), (IDIS | PTU | EN | M4)) /*GPIO_147*/
> +
> +#define MUX_BEAGLE_XM() \
> + MUX_VAL(CP(GPMC_NCS5), (IDIS | PTD | EN | M4)) /*GPIO_56*/\
> + MUX_VAL(CP(GPMC_WAIT1), (IDIS | PTU | EN | M4)) /*GPIO_63*/\
> + MUX_VAL(CP(MMC1_DAT7), (IDIS | PTU | EN | M4)) /*GPIO_129*/\
> + MUX_VAL(CP(HDQ_SIO), (IDIS | PTU | EN | M4)) /*GPIO_170*/\
> + MUX_VAL(CP(MCBSP3_DX), (IEN | PTD | DIS | M4)) /*GPIO_140*/\
> + MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M4)) /*GPIO_142*/\
> + MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M4)) /*GPIO_141*/\
> + MUX_VAL(CP(UART2_CTS), (IEN | PTU | EN | M0)) /*UART2_CTS*/\
> + MUX_VAL(CP(UART2_RTS), (IDIS | PTD | DIS | M0)) /*UART2_RTS*/\
> + MUX_VAL(CP(UART2_TX), (IDIS | PTD | DIS | M0)) /*UART2_TX*/\
> + MUX_VAL(CP(DSS_DATA0), (IDIS | PTD | DIS | M7)) /*safe_mode*/\
> + MUX_VAL(CP(DSS_DATA1), (IDIS | PTD | DIS | M7)) /*safe_mode*/\
> + MUX_VAL(CP(DSS_DATA2), (IDIS | PTD | DIS | M7)) /*safe_mode*/\
> + MUX_VAL(CP(DSS_DATA3), (IDIS | PTD | DIS | M7)) /*safe_mode*/\
> + MUX_VAL(CP(DSS_DATA4), (IDIS | PTD | DIS | M7)) /*safe_mode*/\
> + MUX_VAL(CP(DSS_DATA5), (IDIS | PTD | DIS | M7)) /*safe_mode*/\
> + MUX_VAL(CP(DSS_DATA18), (IDIS | PTD | DIS | M3)) /*DSS_DATA0*/\
> + MUX_VAL(CP(DSS_DATA19), (IDIS | PTD | DIS | M3)) /*DSS_DATA1*/\
> + MUX_VAL(CP(DSS_DATA20), (IDIS | PTD | DIS | M3)) /*DSS_DATA2*/\
> + MUX_VAL(CP(DSS_DATA21), (IDIS | PTD | DIS | M3)) /*DSS_DATA3*/\
> + MUX_VAL(CP(DSS_DATA22), (IDIS | PTD | DIS | M3)) /*DSS_DATA4*/\
> + MUX_VAL(CP(DSS_DATA23), (IDIS | PTD | DIS | M3)) /*DSS_DATA5*/\
> + MUX_VAL(CP(SYS_BOOT0), (IDIS | PTD | DIS | M3)) /*DSS_DATA18*/\
> + MUX_VAL(CP(SYS_BOOT1), (IDIS | PTD | DIS | M3)) /*DSS_DATA19*/\
> + MUX_VAL(CP(SYS_BOOT3), (IDIS | PTD | DIS | M3)) /*DSS_DATA20*/\
> + MUX_VAL(CP(SYS_BOOT4), (IDIS | PTD | DIS | M3)) /*DSS_DATA21*/\
> + MUX_VAL(CP(SYS_BOOT5), (IDIS | PTD | DIS | M3)) /*DSS_DATA22*/\
> + MUX_VAL(CP(SYS_BOOT6), (IDIS | PTD | DIS | M3)) /*DSS_DATA23*/
> +
> +#define MUX_TINCANTOOLS_ZIPPY() \
> + MUX_VAL(CP(MMC2_CLK), (IEN | PTU | EN | M0)) /*MMC2_CLK*/\
> + MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M0)) /*MMC2_CMD*/\
> + MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M0)) /*MMC2_DAT0*/\
> + MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M0)) /*MMC2_DAT1*/\
> + MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M0)) /*MMC2_DAT2*/\
> + MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M0)) /*MMC2_DAT3*/\
> + MUX_VAL(CP(MMC2_DAT4), (IEN | PTU | EN | M1)) /*MMC2_DIR_DAT0*/\
> + MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M1)) /*MMC2_DIR_DAT1*/\
> + MUX_VAL(CP(MMC2_DAT6), (IEN | PTU | EN | M1)) /*MMC2_DIR_CMD*/\
> + MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M1)) /*MMC2_CLKIN*/\
> + MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTU | EN | M1)) /*MCSPI4_CLK*/\
> + MUX_VAL(CP(MCBSP1_FSR), (IEN | PTU | EN | M4)) /*GPIO_157*/\
> + MUX_VAL(CP(MCBSP1_DX), (IEN | PTD | EN | M1)) /*MCSPI4_SIMO*/\
> + MUX_VAL(CP(MCBSP1_DR), (IEN | PTD | DIS | M1)) /*MCSPI4_SOMI*/\
> + MUX_VAL(CP(MCBSP1_FSX), (IEN | PTD | EN | M1)) /*MCSPI4_CS0*/\
> + MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTD | DIS | M4)) /*GPIO_162*/\
> + MUX_VAL(CP(MCBSP3_DX), (IEN | PTD | DIS | M4)) /*GPIO_140*/\
> + MUX_VAL(CP(MCBSP3_DR), (IEN | PTD | DIS | M4)) /*GPIO_142*/\
> + MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTD | DIS | M4)) /*GPIO_141*/
> +
> +#define MUX_TINCANTOOLS_TRAINER() \
> + MUX_VAL(CP(MMC2_CLK), (IEN | PTU | EN | M4)) /*GPIO_130*/\
> + MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M4)) /*GPIO_131*/\
> + MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M4)) /*GPIO_132*/\
> + MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M4)) /*GPIO_133*/\
> + MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M4)) /*GPIO_134*/\
> + MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M4)) /*GPIO_135*/\
> + MUX_VAL(CP(MMC2_DAT4), (IEN | PTU | EN | M4)) /*GPIO_136*/\
> + MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M4)) /*GPIO_137*/\
> + MUX_VAL(CP(MMC2_DAT6), (IEN | PTU | EN | M4)) /*GPIO_138*/\
> + MUX_VAL(CP(MMC2_DAT7), (IEN | PTU | EN | M4)) /*GPIO_139*/\
> + MUX_VAL(CP(MCBSP3_DX), (IEN | PTU | EN | M4)) /*GPIO_140*/\
> + MUX_VAL(CP(MCBSP3_CLKX), (IEN | PTU | EN | M4)) /*GPIO_141*/\
> + MUX_VAL(CP(MCBSP1_CLKX), (IEN | PTU | EN | M4)) /*GPIO_162*/
> +
> +#define MUX_KBADC_BEAGLEFPGA() \
> + MUX_VAL(CP(MCBSP1_CLKR), (IEN | PTU | DIS | M1)) /*MCSPI4_CLK*/\
> + MUX_VAL(CP(MCBSP1_DX), (IDIS | PTU | DIS | M1)) /*MCSPI4_SIMO*/\
> + MUX_VAL(CP(MCBSP1_DR), (IEN | PTU | EN | M1)) /*MCSPI4_SOMI*/\
> + MUX_VAL(CP(MCBSP1_FSX), (IDIS | PTU | DIS | M1)) /*MCSPI4_CS0*/
> +
> +#define MUX_BBTOYS_WIFI() \
> + MUX_VAL(CP(MMC2_CLK), (IEN | PTU | EN | M0)) /*MMC2_CLK*/\
> + MUX_VAL(CP(MMC2_CMD), (IEN | PTU | EN | M0)) /*MMC2_CMD*/\
> + MUX_VAL(CP(MMC2_DAT0), (IEN | PTU | EN | M0)) /*MMC2_DAT0*/\
> + MUX_VAL(CP(MMC2_DAT1), (IEN | PTU | EN | M0)) /*MMC2_DAT1*/\
> + MUX_VAL(CP(MMC2_DAT2), (IEN | PTU | EN | M0)) /*MMC2_DAT2*/\
> + MUX_VAL(CP(MMC2_DAT3), (IEN | PTU | EN | M0)) /*MMC2_DAT3*/\
> + MUX_VAL(CP(MMC2_DAT4), (IDIS | PTU | EN | M4)) /*GPIO_136
> FM_EN/BT_WU*/\
> + MUX_VAL(CP(MMC2_DAT5), (IEN | PTU | EN | M4)) /*GPIO_137
> WLAN_IRQ*/\
> + MUX_VAL(CP(MMC2_DAT6), (IDIS | PTU | EN | M4)) /*GPIO_138 BT_EN*/\
> + MUX_VAL(CP(MMC2_DAT7), (IDIS | PTU | EN | M4)) /*GPIO_139
> WLAN_EN*/
> +
> +/*
> + * Display Configuration
> + */
> +
> +#define DVI_BEAGLE_ORANGE_COL 0x00FF8000
> +#define VENC_HEIGHT 0x00ef
> +#define VENC_WIDTH 0x027f
> +
> +/*
> + * Configure VENC in DSS for Beagle to generate Color Bar
> + *
> + * Kindly refer to OMAP TRM for definition of these values.
> + */
> +static const struct venc_regs venc_config_std_tv = {
> + .status = 0x0000001B,
> + .f_control = 0x00000040,
> + .vidout_ctrl = 0x00000000,
> + .sync_ctrl = 0x00008000,
> + .llen = 0x00008359,
> + .flens = 0x0000020C,
> + .hfltr_ctrl = 0x00000000,
> + .cc_carr_wss_carr = 0x043F2631,
> + .c_phase = 0x00000024,
> + .gain_u = 0x00000130,
> + .gain_v = 0x00000198,
> + .gain_y = 0x000001C0,
> + .black_level = 0x0000006A,
> + .blank_level = 0x0000005C,
> + .x_color = 0x00000000,
> + .m_control = 0x00000001,
> + .bstamp_wss_data = 0x0000003F,
> + .s_carr = 0x21F07C1F,
> + .line21 = 0x00000000,
> + .ln_sel = 0x00000015,
> + .l21__wc_ctl = 0x00001400,
> + .htrigger_vtrigger = 0x00000000,
> + .savid__eavid = 0x069300F4,
> + .flen__fal = 0x0016020C,
> + .lal__phase_reset = 0x00060107,
> + .hs_int_start_stop_x = 0x008D034E,
> + .hs_ext_start_stop_x = 0x000F0359,
> + .vs_int_start_x = 0x01A00000,
> + .vs_int_stop_x__vs_int_start_y = 0x020501A0,
> + .vs_int_stop_y__vs_ext_start_x = 0x01AC0024,
> + .vs_ext_stop_x__vs_ext_start_y = 0x020D01AC,
> + .vs_ext_stop_y = 0x00000006,
> + .avid_start_stop_x = 0x03480079,
> + .avid_start_stop_y = 0x02040024,
> + .fid_int_start_x__fid_int_start_y = 0x0001008A,
> + .fid_int_offset_y__fid_ext_start_x = 0x01AC0106,
> + .fid_ext_start_y__fid_ext_offset_y = 0x01060006,
> + .tvdetgp_int_start_stop_x = 0x00140001,
> + .tvdetgp_int_start_stop_y = 0x00010001,
> + .gen_ctrl = 0x00FF0000,
> + .output_control = 0x0000000D,
> + .dac_b__dac_c = 0x00000000
> +};
> +
> +/*
> + * Configure Timings for DVI D
> + */
> +static const struct panel_config dvid_cfg = {
> + .timing_h = 0x0ff03f31, /* Horizontal timing */
> + .timing_v = 0x01400504, /* Vertical timing */
> + .pol_freq = 0x00007028, /* Pol Freq */
> + .divisor = 0x00010006, /* 72Mhz Pixel Clock */
> + .lcd_size = 0x02ff03ff, /* 1024x768 */
> + .panel_type = 0x01, /* TFT */
> + .data_lines = 0x03, /* 24 Bit RGB */
> + .load_mode = 0x02, /* Frame Mode */
> + .panel_color = DVI_BEAGLE_ORANGE_COL, /* ORANGE */
> + .gfx_format = GFXFORMAT_RGB24_UNPACKED,
> +};
> +
> +static const struct panel_config dvid_cfg_xm = {
> + .timing_h = 0x1a4024c9, /* Horizontal timing */
> + .timing_v = 0x02c00509, /* Vertical timing */
> + .pol_freq = 0x00007028, /* Pol Freq */
> + .divisor = 0x00010001, /* 96MHz Pixel Clock */
> + .lcd_size = 0x02ff03ff, /* 1024x768 */
> + .panel_type = 0x01, /* TFT */
> + .data_lines = 0x03, /* 24 Bit RGB */
> + .load_mode = 0x02, /* Frame Mode */
> + .panel_color = DVI_BEAGLE_ORANGE_COL, /* ORANGE */
> + .gfx_format = GFXFORMAT_RGB24_UNPACKED,
> +};
> +#endif
> diff --git a/board/beagle/beagle/led.c b/board/beagle/beagle/led.c
> new file mode 100644
> index 00000000000..9daec4f48dc
> --- /dev/null
> +++ b/board/beagle/beagle/led.c
> @@ -0,0 +1,70 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2010 Texas Instruments, Inc.
> + * Jason Kridner <jkrid...@beagleboard.org>
> + */
> +#include <status_led.h>
> +#include <asm/arch/cpu.h>
> +#include <asm/io.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/gpio.h>
> +
> +/* GPIO pins for the LEDs */
> +#define BEAGLE_LED_USR0 150
> +#define BEAGLE_LED_USR1 149
> +
> +#if (IS_ENABLED(CONFIG_LED_STATUS_GREEN))
> +void green_led_off(void)
> +{
> + __led_set(CONFIG_LED_STATUS_GREEN, 0);
> +}
> +
> +void green_led_on(void)
> +{
> + __led_set(CONFIG_LED_STATUS_GREEN, 1);
> +}
> +#endif
> +
> +static int get_led_gpio(led_id_t mask)
> +{
> +#if (IS_ENABLED(CONFIG_LED_STATUS0))
> + if (CONFIG_LED_STATUS_BIT & mask)
> + return BEAGLE_LED_USR0;
> +#endif
> +#if (IS_ENABLED(CONFIG_LED_STATUS1))
> + if (CONFIG_LED_STATUS_BIT1 & mask)
> + return BEAGLE_LED_USR1;
> +#endif
> +
> + return 0;
> +}
> +
> +void __led_init(led_id_t mask, int state)
> +{
> + int toggle_gpio;
> +
> + toggle_gpio = get_led_gpio(mask);
> +
> + if (toggle_gpio && !gpio_request(toggle_gpio, "led"))
> + __led_set(mask, state);
> +}
> +
> +void __led_toggle(led_id_t mask)
> +{
> + int state, toggle_gpio;
> +
> + toggle_gpio = get_led_gpio(mask);
> + if (toggle_gpio) {
> + state = gpio_get_value(toggle_gpio);
> + gpio_direction_output(toggle_gpio, !state);
> + }
> +}
> +
> +void __led_set(led_id_t mask, int state)
> +{
> + int toggle_gpio;
> +
> + toggle_gpio = get_led_gpio(mask);
> + if (toggle_gpio)
> + gpio_direction_output(toggle_gpio, state);
> +}
> diff --git a/board/isee/igep00x0/spl.c b/board/isee/igep00x0/spl.c
> index f814fe13542..18e15215c36 100644
> --- a/board/isee/igep00x0/spl.c
> +++ b/board/isee/igep00x0/spl.c
> @@ -34,19 +34,19 @@ void get_board_mem_timings(struct board_sdrc_timings
> *timings)
> /* Should not happen... */
> break;
> }
> - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHZ;
> gpmc_cs0_flash = MTD_DEV_TYPE_NAND;
> } else {
> if (get_cpu_family() == CPU_OMAP34XX) {
> timings->mcfg = NUMONYX_V_MCFG_165(256 << 20);
> timings->ctrla = NUMONYX_V_ACTIMA_165;
> timings->ctrlb = NUMONYX_V_ACTIMB_165;
> - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHZ;
> } else {
> timings->mcfg = NUMONYX_V_MCFG_200(256 << 20);
> timings->ctrla = NUMONYX_V_ACTIMA_200;
> timings->ctrlb = NUMONYX_V_ACTIMB_200;
> - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHZ;
> }
> gpmc_cs0_flash = MTD_DEV_TYPE_ONENAND;
> }
> diff --git a/board/lg/sniper/sniper.c b/board/lg/sniper/sniper.c
> index d4db32ee69b..8a04baf0094 100644
> --- a/board/lg/sniper/sniper.c
> +++ b/board/lg/sniper/sniper.c
> @@ -60,7 +60,7 @@ void get_board_mem_timings(struct board_sdrc_timings
> *timings)
> timings->mcfg = HYNIX_V_MCFG_200(256 << 20);
> timings->ctrla = HYNIX_V_ACTIMA_200;
> timings->ctrlb = HYNIX_V_ACTIMB_200;
> - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHZ;
> timings->mr = MICRON_V_MR_165;
> }
>
> diff --git a/board/logicpd/omap3som/omap3logic.c
> b/board/logicpd/omap3som/omap3logic.c
> index 352b519b451..80bdfeab359 100644
> --- a/board/logicpd/omap3som/omap3logic.c
> +++ b/board/logicpd/omap3som/omap3logic.c
> @@ -86,13 +86,13 @@ void get_board_mem_timings(struct board_sdrc_timings
> *timings)
> timings->mcfg = MICRON_V_MCFG_200(256 << 20);
> timings->ctrla = MICRON_V_ACTIMA_200;
> timings->ctrlb = MICRON_V_ACTIMB_200;
> - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHz;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_200MHZ;
> } else {
> /* 165 MHz works for OMAP35 */
> timings->mcfg = MICRON_V_MCFG_165(256 << 20);
> timings->ctrla = MICRON_V_ACTIMA_165;
> timings->ctrlb = MICRON_V_ACTIMB_165;
> - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHZ;
> }
> }
>
> diff --git a/board/ti/omap3evm/evm.c b/board/ti/omap3evm/evm.c
> index 8803643b032..252a2909d64 100644
> --- a/board/ti/omap3evm/evm.c
> +++ b/board/ti/omap3evm/evm.c
> @@ -147,7 +147,7 @@ void get_board_mem_timings(struct board_sdrc_timings
> *timings)
> timings->ctrla = MICRON_V_ACTIMA_165;
> timings->ctrlb = MICRON_V_ACTIMB_165;
> }
> - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHZ;
> timings->mr = MICRON_V_MR_165;
> }
> #endif /* CONFIG_XPL_BUILD */
> diff --git a/board/timll/devkit8000/devkit8000.c
> b/board/timll/devkit8000/devkit8000.c
> index a2a3a9489aa..07aedc46cec 100644
> --- a/board/timll/devkit8000/devkit8000.c
> +++ b/board/timll/devkit8000/devkit8000.c
> @@ -198,7 +198,7 @@ void get_board_mem_timings(struct board_sdrc_timings
> *timings)
> {
> /* General SDRC config */
> timings->mcfg = MICRON_V_MCFG_165(128 << 20);
> - timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
> + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHZ;
>
> /* AC timings */
> timings->ctrla = MICRON_V_ACTIMA_165;
> diff --git a/configs/omap3_beagle_defconfig b/configs/omap3_beagle_defconfig
> new file mode 100644
> index 00000000000..a6cf155426d
> --- /dev/null
> +++ b/configs/omap3_beagle_defconfig
> @@ -0,0 +1,124 @@
> +CONFIG_ARM=y
> +# CONFIG_SPL_USE_ARCH_MEMCPY is not set
> +# CONFIG_SPL_USE_ARCH_MEMSET is not set
> +CONFIG_ARCH_OMAP2PLUS=y
> +CONFIG_SYS_MALLOC_F_LEN=0x4000
> +CONFIG_EEPROM_BUS_ADDRESS=1
> +CONFIG_TI_COMMON_CMD_OPTIONS=y
> +CONFIG_DEFAULT_DEVICE_TREE="ti/omap/omap3-beagle"
> +CONFIG_TARGET_OMAP3_BEAGLE=y
> +CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
> +CONFIG_SPL=y
> +CONFIG_ENV_VARS_UBOOT_CONFIG=y
> +# CONFIG_EFI_LOADER is not set
> +# CONFIG_ANDROID_BOOT_IMAGE is not set
> +# CONFIG_BOOTSTD is not set
> +CONFIG_SUPPORT_RAW_INITRD=y
> +CONFIG_USE_BOOTCOMMAND=y
> +CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
> +CONFIG_USE_PREBOOT=y
> +CONFIG_DEFAULT_FDT_FILE="omap3-beagle.dtb"
> +CONFIG_SYS_PBSIZE=1055
> +CONFIG_SYS_CONSOLE_INFO_QUIET=y
> +CONFIG_ANDROID_AB=y
> +CONFIG_SPL_PAD_TO=0x0
> +CONFIG_SPL_SYS_MALLOC_SIMPLE=y
> +# CONFIG_SPL_FS_EXT4 is not set
> +CONFIG_SPL_MTD=y
> +CONFIG_SPL_NAND_DRIVERS=y
> +CONFIG_SPL_NAND_ECC=y
> +CONFIG_SPL_NAND_SIMPLE=y
> +CONFIG_SPL_NAND_BASE=y
> +CONFIG_HUSH_PARSER=y
> +CONFIG_SYS_PROMPT="BeagleBoard # "
> +CONFIG_CMD_CONFIG=y
> +# CONFIG_BOOTM_PLAN9 is not set
> +# CONFIG_BOOTM_RTEMS is not set
> +# CONFIG_BOOTM_VXWORKS is not set
> +# CONFIG_CMD_ELF is not set
> +# CONFIG_CMD_XIMG is not set
> +# CONFIG_CMD_DFU is not set
> +# CONFIG_CMD_GPT is not set
> +# CONFIG_CMD_MMC_REG is not set
> +# CONFIG_MMC_SPEED_MODE_SET is not set
> +CONFIG_CMD_NAND=y
> +CONFIG_CMD_NAND_TRIMFFS=y
> +# CONFIG_CMD_NFS is not set
> +CONFIG_CMD_CACHE=y
> +# CONFIG_CMD_TIME is not set
> +CONFIG_CMD_SYSBOOT=y
> +# CONFIG_CMD_PMIC is not set
> +# CONFIG_CMD_REGULATOR is not set
> +CONFIG_CMD_SQUASHFS=y
> +CONFIG_CMD_FS_UUID=y
> +CONFIG_CMD_MTDPARTS=y
> +CONFIG_MTDIDS_DEFAULT="nand0=omap2-nand.0"
> +CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:512k(spl),1920k(u-boot),128k(u-boot-env),128k(dtb),6m(kernel),-(rootfs)"
> +CONFIG_CMD_UBI=y
> +CONFIG_EFI_PARTITION=y
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_OF_CONTROL=y
> +CONFIG_SPL_OF_CONTROL=y
> +CONFIG_OF_SPL_REMOVE_PROPS="clocks clock-names interrupt-parent"
> +CONFIG_ENV_OVERWRITE=y
> +# CONFIG_ENV_IS_IN_FAT is not set
> +CONFIG_ENV_IS_IN_NAND=y
> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
> +CONFIG_VERSION_VARIABLE=y
> +CONFIG_SPL_DM=y
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +CONFIG_SPL_OF_TRANSLATE=y
> +CONFIG_USB_FUNCTION_FASTBOOT=y
> +CONFIG_FASTBOOT_BUF_ADDR=0x82000000
> +CONFIG_LED_STATUS=y
> +CONFIG_LED_STATUS0=y
> +CONFIG_LED_STATUS_BIT=1
> +CONFIG_LED_STATUS_STATE=2
> +CONFIG_LED_STATUS1=y
> +CONFIG_LED_STATUS_BIT1=2
> +CONFIG_LED_STATUS_STATE1=2
> +CONFIG_LED_STATUS_BOOT_ENABLE=y
> +CONFIG_LED_STATUS_BOOT=1
> +CONFIG_LED_STATUS_GREEN_ENABLE=y
> +CONFIG_LED_STATUS_GREEN=2
> +CONFIG_LED_STATUS_CMD=y
> +CONFIG_TWL4030_LED=y
> +CONFIG_MMC_OMAP_HS=y
> +CONFIG_MTD=y
> +CONFIG_DM_MTD=y
> +CONFIG_MTD_RAW_NAND=y
> +CONFIG_NAND_OMAP_ECCSCHEME_HAM1_CODE_HW=y
> +CONFIG_SYS_NAND_BLOCK_SIZE=0x20000
> +CONFIG_SYS_NAND_PAGE_SIZE=0x800
> +CONFIG_SYS_NAND_OOBSIZE=0x40
> +CONFIG_SYS_NAND_BUSWIDTH_16BIT=y
> +CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
> +CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000
> +CONFIG_DM_PMIC=y
> +# CONFIG_SPL_DM_PMIC is not set
> +CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_REGULATOR_GPIO=y
> +CONFIG_SPI=y
> +CONFIG_DM_SPI=y
> +CONFIG_OMAP3_SPI=y
> +CONFIG_USB=y
> +# CONFIG_SPL_DM_USB is not set
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_OMAP3=y
> +CONFIG_USB_MUSB_GADGET=y
> +CONFIG_USB_MUSB_OMAP2PLUS=y
> +CONFIG_TWL4030_USB=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_USB_HOST_ETHER=y
> +CONFIG_USB_ETHER_ASIX=y
> +CONFIG_USB_ETHER_MCS7830=y
> +CONFIG_USB_ETHER_SMSC95XX=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_MANUFACTURER="TI"
> +CONFIG_USB_GADGET_VENDOR_NUM=0x0451
> +CONFIG_USB_GADGET_PRODUCT_NUM=0xd022
> +CONFIG_USB_ETHER=y
> +CONFIG_BCH=y
> +CONFIG_SPL_CRC8=y
> diff --git a/configs/omap3_beagle_xm_defconfig
> b/configs/omap3_beagle_xm_defconfig
> new file mode 100644
> index 00000000000..42e01d86361
> --- /dev/null
> +++ b/configs/omap3_beagle_xm_defconfig
> @@ -0,0 +1,109 @@
> +CONFIG_ARM=y
> +# CONFIG_SPL_USE_ARCH_MEMCPY is not set
> +# CONFIG_SPL_USE_ARCH_MEMSET is not set
> +CONFIG_ARCH_OMAP2PLUS=y
> +CONFIG_SYS_MALLOC_F_LEN=0x4000
> +CONFIG_EEPROM_BUS_ADDRESS=1
> +CONFIG_TI_COMMON_CMD_OPTIONS=y
> +CONFIG_DEFAULT_DEVICE_TREE="ti/omap/omap3-beagle-xm"
> +CONFIG_TARGET_OMAP3_BEAGLE=y
> +CONFIG_SPL_SYS_MALLOC_F_LEN=0x400
> +CONFIG_SPL=y
> +CONFIG_ENV_VARS_UBOOT_CONFIG=y
> +# CONFIG_EFI_LOADER is not set
> +# CONFIG_ANDROID_BOOT_IMAGE is not set
> +# CONFIG_BOOTSTD is not set
> +CONFIG_SUPPORT_RAW_INITRD=y
> +CONFIG_USE_BOOTCOMMAND=y
> +CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
> +CONFIG_USE_PREBOOT=y
> +CONFIG_DEFAULT_FDT_FILE="omap3-beagle-xm.dtb"
> +CONFIG_SYS_CONSOLE_INFO_QUIET=y
> +CONFIG_ANDROID_AB=y
> +CONFIG_SPL_PAD_TO=0x0
> +CONFIG_SPL_SYS_MALLOC_SIMPLE=y
> +# CONFIG_SPL_FS_EXT4 is not set
> +CONFIG_SPL_MTD=y
> +# CONFIG_SPL_NAND_SUPPORT is not set
> +CONFIG_HUSH_PARSER=y
> +CONFIG_SYS_PROMPT="BeagleBoard-xM # "
> +CONFIG_CMD_CONFIG=y
> +# CONFIG_BOOTM_PLAN9 is not set
> +# CONFIG_BOOTM_RTEMS is not set
> +# CONFIG_BOOTM_VXWORKS is not set
> +# CONFIG_CMD_ELF is not set
> +# CONFIG_CMD_XIMG is not set
> +# CONFIG_CMD_DFU is not set
> +# CONFIG_CMD_GPT is not set
> +# CONFIG_CMD_MMC_REG is not set
> +# CONFIG_MMC_SPEED_MODE_SET is not set
> +# CONFIG_CMD_NFS is not set
> +CONFIG_CMD_CACHE=y
> +# CONFIG_CMD_TIME is not set
> +CONFIG_CMD_SYSBOOT=y
> +# CONFIG_CMD_PMIC is not set
> +# CONFIG_CMD_REGULATOR is not set
> +CONFIG_CMD_SQUASHFS=y
> +CONFIG_CMD_FS_UUID=y
> +CONFIG_CMD_MTDPARTS=y
> +CONFIG_MTDIDS_DEFAULT="nand0=omap2-nand.0"
> +CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:512k(spl),1920k(u-boot),128k(u-boot-env),128k(dtb),6m(kernel),-(rootfs)"
> +CONFIG_CMD_UBI=y
> +CONFIG_EFI_PARTITION=y
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_OF_CONTROL=y
> +CONFIG_SPL_OF_CONTROL=y
> +CONFIG_OF_SPL_REMOVE_PROPS="clocks clock-names interrupt-parent"
> +CONFIG_ENV_OVERWRITE=y
> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_SYS_MMC_ENV_PART=1
> +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
> +CONFIG_VERSION_VARIABLE=y
> +CONFIG_SPL_DM=y
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +CONFIG_SPL_OF_TRANSLATE=y
> +CONFIG_USB_FUNCTION_FASTBOOT=y
> +CONFIG_FASTBOOT_BUF_ADDR=0x82000000
> +CONFIG_LED_STATUS=y
> +CONFIG_LED_STATUS0=y
> +CONFIG_LED_STATUS_BIT=1
> +CONFIG_LED_STATUS_STATE=2
> +CONFIG_LED_STATUS1=y
> +CONFIG_LED_STATUS_BIT1=2
> +CONFIG_LED_STATUS_STATE1=2
> +CONFIG_LED_STATUS_BOOT_ENABLE=y
> +CONFIG_LED_STATUS_BOOT=1
> +CONFIG_LED_STATUS_GREEN_ENABLE=y
> +CONFIG_LED_STATUS_GREEN=2
> +CONFIG_LED_STATUS_CMD=y
> +CONFIG_TWL4030_LED=y
> +CONFIG_MMC_OMAP_HS=y
> +CONFIG_MTD=y
> +CONFIG_DM_MTD=y
> +CONFIG_DM_PMIC=y
> +# CONFIG_SPL_DM_PMIC is not set
> +CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_REGULATOR_GPIO=y
> +CONFIG_SPI=y
> +CONFIG_DM_SPI=y
> +CONFIG_OMAP3_SPI=y
> +CONFIG_USB=y
> +# CONFIG_SPL_DM_USB is not set
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_OMAP3=y
> +CONFIG_USB_MUSB_GADGET=y
> +CONFIG_USB_MUSB_OMAP2PLUS=y
> +CONFIG_TWL4030_USB=y
> +CONFIG_USB_STORAGE=y
> +CONFIG_USB_HOST_ETHER=y
> +CONFIG_USB_ETHER_ASIX=y
> +CONFIG_USB_ETHER_MCS7830=y
> +CONFIG_USB_ETHER_SMSC95XX=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_MANUFACTURER="TI"
> +CONFIG_USB_GADGET_VENDOR_NUM=0x0451
> +CONFIG_USB_GADGET_PRODUCT_NUM=0xd022
> +CONFIG_USB_ETHER=y
> +CONFIG_BCH=y
> +CONFIG_SPL_CRC8=y
> diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
> new file mode 100644
> index 00000000000..d3737ce97dd
> --- /dev/null
> +++ b/include/configs/omap3_beagle.h
> @@ -0,0 +1,201 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * (C) Copyright 2006-2008
> + * Texas Instruments.
> + * Richard Woodruff <r-woodru...@ti.com>
> + * Syed Mohammed Khasim <x0kha...@ti.com>
> + *
> + * Configuration settings for the TI OMAP3530 Beagle board.
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#include <configs/ti_omap3_common.h>
> +
> +/*
> + * We are only ever GP parts and will utilize all of the "downloaded image"
> + * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB).
> + */
> +
> +/* NAND */
> +#if defined(CONFIG_MTD_RAW_NAND)
> +#define CFG_SYS_FLASH_BASE NAND_BASE
> +#define CFG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 }
> +#define CFG_SYS_NAND_ECCSIZE 512
> +#define CFG_SYS_NAND_ECCBYTES 3
> +/* NAND: SPL falcon mode configs */
> +#endif /* CONFIG_MTD_RAW_NAND */
> +
> +/* DSS Support */
> +
> +/* TWL4030 LED Support */
> +
> +#define MEM_LAYOUT_ENV_SETTINGS \
> + DEFAULT_LINUX_BOOT_ENV
> +
> +#define BOOTENV_DEV_LEGACY_MMC(devtypeu, devtypel, instance) \
> + "bootcmd_" #devtypel #instance "=" \
> + "setenv mmcdev " #instance "; " \
> + "run mmcboot\0"
> +#define BOOTENV_DEV_NAME_LEGACY_MMC(devtypeu, devtypel, instance) \
> + #devtypel #instance " "
> +
> +#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
> +#define BOOT_TARGET_DEVICES_MMC_LEGACY(func) func(LEGACY_MMC, legacy_mmc, 0)
> +
> +#if defined(CONFIG_MTD_RAW_NAND)
> +
> +#define BOOTENV_DEV_NAND(devtypeu, devtypel, instance) \
> + "bootcmd_" #devtypel #instance "=" \
> + "if test ${mtdids} = '' || test ${mtdparts} = '' ; then " \
> + "echo NAND boot disabled: No mtdids and/or mtdparts; " \
> + "else " \
> + "run nandboot; " \
> + "fi\0"
> +#define BOOTENV_DEV_NAME_NAND(devtypeu, devtypel, instance) \
> + #devtypel #instance " "
> +
> +#define BOOT_TARGET_DEVICES_UBIFS(func) func(UBIFS, ubifs, 0, rootfs,
> rootfs)
> +#define BOOT_TARGET_DEVICES_NAND(func) func(NAND, nand, 0)
> +
> +#define BOOT_TARGET_DEVICES(func) \
> + BOOT_TARGET_DEVICES_MMC(func) \
> + BOOT_TARGET_DEVICES_MMC_LEGACY(func) \
> + BOOT_TARGET_DEVICES_UBIFS(func) \
> + BOOT_TARGET_DEVICES_NAND(func)
> +
> +#else /* !CONFIG_MTD_RAW_NAND */
> +
> +#define BOOT_TARGET_DEVICES(func) \
> + BOOT_TARGET_DEVICES_MMC(func) \
> + BOOT_TARGET_DEVICES_MMC_LEGACY(func)
> +
> +#endif /* CONFIG_MTD_RAW_NAND */
> +
> +#include <config_distro_bootcmd.h>
> +
> +#define CFG_EXTRA_ENV_SETTINGS \
> + MEM_LAYOUT_ENV_SETTINGS \
> + "fdtfile=" CONFIG_DEFAULT_FDT_FILE "\0" \
> + "console=ttyO2,115200n8\0" \
> + "bootdir=/boot\0" \
> + "bootenv=uEnv.txt\0" \
> + "bootfile=zImage\0" \
> + "bootpart=0:2\0" \
> + "usbtty=cdc_acm\0" \
> + "mpurate=auto\0" \
> + "buddy=none\0" \
> + "camera=none\0" \
> + "vram=12M\0" \
> + "dvimode=640x480MR-16@60\0" \
> + "defaultdisplay=dvi\0" \
> + "defaultargs=setenv defargs " \
> + "mpurate=${mpurate} " \
> + "buddy=${buddy} "\
> + "camera=${camera} "\
> + "vram=${vram} " \
> + "omapfb.mode=dvi:${dvimode} " \
> + "omapdss.def_disp=${defaultdisplay}\0" \
> + "optargs=\0" \
> + "findfdt=" \
> + "if test $beaglerev = AxBx; then " \
> + "setenv fdtfile omap3-beagle.dtb; fi; " \
> + "if test $beaglerev = Cx; then " \
> + "setenv fdtfile omap3-beagle.dtb; fi; " \
> + "if test $beaglerev = C4; then " \
> + "setenv fdtfile omap3-beagle.dtb; fi; " \
> + "if test $beaglerev = xMAB; then " \
> + "setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \
> + "if test $beaglerev = xMC; then " \
> + "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
> + "if test $fdtfile = undefined; then " \
> + "echo WARNING: Could not determine device tree to use;
> fi\0" \
> + "mmcdev=0\0" \
> + "mmcpart=2\0" \
> + "mmcroot=/dev/mmcblk0p2 rw\0" \
> + "mmcrootfstype=ext4 rootwait\0" \
> + "mmcargs=run defaultargs; setenv bootargs console=${console} " \
> + "${mtdparts} " \
> + "${defargs} " \
> + "${optargs} " \
> + "root=${mmcroot} " \
> + "rootfstype=${mmcrootfstype}\0" \
> + "userbutton_xm=gpio input 4;\0" \
> + "userbutton_nonxm=gpio input 7;\0" \
> + "userbutton=if gpio input 173; then " \
> + "run userbutton_xm; " \
> + "else " \
> + "run userbutton_nonxm; " \
> + "fi;\0" \
> + "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
> + "ext4bootenv=ext4load mmc ${bootpart} ${loadaddr}
> ${bootdir}/${bootenv}\0" \
> + "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
> + "env import -t ${loadaddr} ${filesize}\0" \
> + "mmcbootenv=setenv bootpart ${mmcdev}:${mmcpart}; " \
> + "mmc dev ${mmcdev}; " \
> + "if mmc rescan; then " \
> + "if run userbutton; then " \
> + "setenv bootenv uEnv.txt;" \
> + "else " \
> + "setenv bootenv user.txt;" \
> + "fi;" \
> + "run loadbootenv && run importbootenv; " \
> + "run ext4bootenv && run importbootenv; " \
> + "if test -n $uenvcmd; then " \
> + "echo Running uenvcmd ...; " \
> + "run uenvcmd; " \
> + "fi; " \
> + "fi\0" \
> + "validatefdt=" \
> + "if test $beaglerev = xMAB; then " \
> + "if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile};
> then " \
> + "setenv fdtfile omap3-beagle-xm.dtb; " \
> + "fi; " \
> + "fi; \0" \
> + "loadimage=ext4load mmc ${bootpart} ${loadaddr}
> ${bootdir}/${bootfile}\0" \
> + "loaddtb=run validatefdt; ext4load mmc ${bootpart} ${fdtaddr}
> ${bootdir}/${fdtfile}\0" \
> + "mmcboot=run mmcbootenv; " \
> + "if run loadimage && run loaddtb; then " \
> + "echo Booting ${bootdir}/${bootfile} from mmc
> ${bootpart} ...; " \
> + "run mmcargs; " \
> + "if test ${bootfile} = uImage; then " \
> + "bootm ${loadaddr} - ${fdtaddr}; " \
> + "fi; " \
> + "if test ${bootfile} = zImage; then " \
> + "bootz ${loadaddr} - ${fdtaddr}; " \
> + "fi; " \
> + "fi\0" \
> + "nandroot=ubi0:rootfs ubi.mtd=rootfs rw\0" \
> + "nandrootfstype=ubifs rootwait\0" \
> + "nandargs=run defaultargs; setenv bootargs console=${console} " \
> + "${mtdparts} " \
> + "${defargs} " \
> + "${optargs} " \
> + "root=${nandroot} " \
> + "rootfstype=${nandrootfstype}\0" \
> + "nandboot=if nand read ${loadaddr} kernel && nand read ${fdtaddr} dtb;
> then " \
> + "echo Booting uImage from NAND MTD 'kernel' partition
> ...; " \
> + "run nandargs; " \
> + "bootm ${loadaddr} - ${fdtaddr}; " \
> + "fi\0" \
> + "loadramdisk=ext4load mmc ${bootpart} ${rdaddr}
> ${bootdir}/${ramdisk}\0" \
> + "ramdisk=rootfs.ext2.gz.uboot\0" \
> + "ramdisk_size=16384\0" \
> + "ramroot=/dev/ram rw\0" \
> + "ramrootfstype=ext2\0" \
> + "ramargs=run defaultargs; setenv bootargs console=${console} " \
> + "${mtdparts} " \
> + "${defargs} " \
> + "${optargs} " \
> + "root=${ramroot} ramdisk_size=${ramdisk_size} " \
> + "rootfstype=${ramrootfstype}\0" \
> + "ramboot=run mmcbootenv; " \
> + "if run loadimage && run loaddtb && run loadramdisk; then " \
> + "echo Booting ${bootdir}/${bootfile} from mmc
> ${bootpart} w/ramdisk ...; " \
> + "run ramargs; " \
> + "bootz ${loadaddr} ${rdaddr} ${fdtaddr}; " \
> + "fi\0" \
> + BOOTENV
> +
> +#endif /* __CONFIG_H */
> --
> 2.43.0
>
>
For BeagleBoard Rev. C [ SD/MMC boot ]
Tested-by: Derald D. Woods <woods.techni...@gmail.com>
----------------------------------------------------------------
U-Boot SPL 2025.07-rc2-28-g17e0fd0e469-00028-g17e0fd0e4697 (May 20 2025 -
22:46:53 -0400)
Trying to boot from MMC1
U-Boot 2025.07-rc2-28-g17e0fd0e469-00028-g17e0fd0e4697 (May 20 2025 - 22:46:53
-0400)
OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 MHz
Model: TI OMAP3 BeagleBoard
OMAP3 Beagle board + LPDDR/NAND
DRAM: 256 MiB
Core: 50 devices, 16 uclasses, devicetree: separate
NAND: 256 MiB
MMC: OMAP SD/MMC: 0
Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
Beagle Rev C4
Timed out in wait_for_event: status=0000
Check if pads/pull-ups of bus are properly configured
Unrecognized expansion board: 0
OMAP die ID: 1ffc0004000000000403a38103018017
Net: No ethernet found.
Hit any key to stop autoboot: 0
BeagleBoard #
----------------------------------------------------------------
- Derald
