commit: http://blackfin.uclinux.org/git/?p=u-boot;a=commitdiff;h=2ddc147fa1d4d46e65ea75915cdf322f8829dc5a branch: http://blackfin.uclinux.org/git/?p=u-boot;a=shortlog;h=refs/heads/trunk
- Disable NAND driver on bf537-stamp. - Disable LCD driver on bf527-ezkit. - Enlarge BF609 nor flash reserved size from 256k to 512k bytes. Signed-off-by: Sonic Zhang <sonic.zh...@analog.com> --- include/configs/bf527-ezkit.h | 12 ++++++------ include/configs/bf537-stamp.h | 7 ++++--- include/configs/bf609-ezkit.h | 2 ++ 3 files changed, 12 insertions(+), 9 deletions(-) diff --git a/include/configs/bf527-ezkit.h b/include/configs/bf527-ezkit.h index 7b51b53..db1b613 100644 --- a/include/configs/bf527-ezkit.h +++ b/include/configs/bf527-ezkit.h @@ -149,10 +149,15 @@ #define CONFIG_MUSB_TIMEOUT 100000 #endif +/* Don't waste time transferring a logo over the UART */ +#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART) +/*# define CONFIG_VIDEO*/ +#endif /* * Video Settings */ +#ifdef CONFIG_VIDEO #ifdef CONFIG_BF527_EZKIT_REV_2_1 # define CONFIG_LQ035Q1_SPI_BUS 0 # define CONFIG_LQ035Q1_SPI_CS 7 @@ -166,7 +171,7 @@ #else # define EASYLOGO_HEADER <asm/bfin_logo_230x230_lzma.h> #endif - +#endif /* CONFIG_VIDEO */ /* * Misc Settings @@ -175,11 +180,6 @@ #define CONFIG_RTC_BFIN #define CONFIG_UART_CONSOLE 1 -/* Don't waste time transferring a logo over the UART */ -#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART) -# define CONFIG_VIDEO -#endif - /* * Pull in common ADI header for remaining command/environment setup diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index c824d59..25cebf8 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -52,7 +52,7 @@ #define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) #define CONFIG_SYS_MALLOC_LEN (384 * 1024) @@ -144,7 +144,8 @@ /* * NAND Settings */ -#define CONFIG_NAND_PLAT +/* #define CONFIG_NAND_PLAT */ +#ifdef CONFIG_NAND_PLAT #define CONFIG_SYS_NAND_BASE 0x20212000 #define CONFIG_SYS_MAX_NAND_DEVICE 1 @@ -159,7 +160,7 @@ #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) #define NAND_PLAT_GPIO_DEV_READY GPIO_PF3 - +#endif /* CONFIG_NAND_PLAT */ /* * CF-CARD IDE-HDD Support diff --git a/include/configs/bf609-ezkit.h b/include/configs/bf609-ezkit.h index 4ad46fb..d8b0739 100644 --- a/include/configs/bf609-ezkit.h +++ b/include/configs/bf609-ezkit.h @@ -183,6 +183,8 @@ #undef CONFIG_UART_CONSOLE_IS_JTAG #endif +#define CONFIG_BOARD_SIZE_LIMIT $$(( 512 * 1024 )) + /* * Run core 1 from L1 SRAM start address when init uboot on core 0 */
_______________________________________________ U-Boot-commits mailing list U-Boot-commits@blackfin.uclinux.org https://blackfin.uclinux.org/mailman/listinfo/u-boot-commits
