Add MII commands to the UEC driver. Note that once a UEC device is
selected, any device on its MDIO bus can be addressed.

Signed-off-by: David Saada <[EMAIL PROTECTED]>

diff -purN a/drivers/qe/uec.c b/drivers/qe/uec.c
--- a/drivers/qe/uec.c  2008-01-14 11:48:28.000000000 +0200
+++ b/drivers/qe/uec.c  2008-01-15 10:25:46.411493000 +0200
@@ -29,6 +29,7 @@
 #include "uccf.h"
 #include "uec.h"
 #include "uec_phy.h"
+#include "miiphy.h"
 
 #if defined(CONFIG_QE)
 
@@ -88,6 +89,17 @@ static uec_info_t eth3_uec_info = {
 };
 #endif
 
+#define MAXCONTROLLERS (4)
+
+static struct eth_device *devlist[MAXCONTROLLERS];
+
+static int uec_miiphy_read(char *devname, unsigned char addr,
+                           unsigned char reg, unsigned short *value);
+static int uec_miiphy_write(char *devname, unsigned char addr,
+                            unsigned char reg, unsigned short value);
+u16 phy_read (struct uec_mii_info *mii_info, u16 regnum);
+void phy_write (struct uec_mii_info *mii_info, u16 regnum, u16 val);
+
 static int uec_mac_enable(uec_private_t *uec, comm_dir_e mode)
 {
        uec_t           *uec_regs;
@@ -1267,6 +1279,8 @@ int uec_initialize(int index)
                return -EINVAL;
        }
 
+       devlist[index] = dev;
+       
        uec->uec_info = uec_info;
 
        sprintf(dev->name, "FSL UEC%d", index);
@@ -1297,6 +1311,45 @@ int uec_initialize(int index)
 
        phy_change(dev);
 
+#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) \
+       && !defined(BITBANGMII)
+       miiphy_register(dev->name, uec_miiphy_read, uec_miiphy_write);
+#endif
+
        return 1;
 }
+
+#if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) \
+       && !defined(BITBANGMII)
+
+/*
+ * Read a MII PHY register.
+ *
+ * Returns:
+ *  0 on success
+ */
+static int uec_miiphy_read(char *devname, unsigned char addr,
+                           unsigned char reg, unsigned short *value)
+{
+       *value = uec_read_phy_reg(devlist[0], addr, reg);
+
+       return 0;
+}
+
+/*
+ * Write a MII PHY register.
+ *
+ * Returns:
+ *  0 on success
+ */
+static int uec_miiphy_write(char *devname, unsigned char addr,
+                            unsigned char reg, unsigned short value)
+{
+       uec_write_phy_reg(devlist[0], addr, reg, value);
+
+       return 0;
+}
+
+#endif
+
 #endif /* CONFIG_QE */

-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users

Reply via email to