According to the application notes of the DM9000 v1.22 chapter 5.2 bullet 2,
the
reset procedure must be done twice to properly reset the DM9000 by means of
software.
This errata is not needed anymore for the DM9000A, but it does not bother it.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <[EMAIL PROTECTED]>
---
drivers/net/dm9000x.c | 34 +++++++++++++++++++++++++++++++---
1 file changed, 31 insertions(+), 3 deletions(-)
Index: u-boot-git-22052008/drivers/net/dm9000x.c
===================================================================
--- u-boot-git-22052008.orig/drivers/net/dm9000x.c 2008-06-03
12:06:57.000000000 +0200
+++ u-boot-git-22052008/drivers/net/dm9000x.c 2008-06-03 12:07:51.000000000
+0200
@@ -45,6 +45,8 @@ v1.2 03/18/2003 Weilun Huang <we
- Adapt eth_send such that it matches the DM9000*
application notes. Needed to make it work properly
for DM9000A.
+ - Adapted reset procedure to match DM9000 application
+ notes (i.e. double reset)
These changes are tested with DM9000{A,EP,E} together
with a 200MHz Atmel AT91SAM92161 core
@@ -362,9 +364,35 @@ identify_nic(void)
static void
dm9000_reset(void)
{
- DM9000_DBG("resetting\n");
- DM9000_iow(DM9000_NCR, NCR_RST);
- udelay(1000); /* delay 1ms */
+ DM9000_DBG("resetting DM9000\n");
+
+ /* Reset DM9000,
+ see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 */
+
+ /* DEBUG: Make all GPIO pins outputs */
+ DM9000_iow(DM9000_GPCR, 0x0F);
+ /* Step 1: Power internal PHY by writing 0 to GPIO0 pin */
+ DM9000_iow(DM9000_GPR, 0);
+ /* Step 2: Software reset */
+ DM9000_iow(DM9000_NCR, 3);
+
+ do {
+ DM9000_DBG("resetting the DM9000, 1st reset\n");
+ udelay(25); /* Wait at least 20 us */
+ } while (DM9000_ior(DM9000_NCR) & 1);
+
+ DM9000_iow(DM9000_NCR, 0);
+ DM9000_iow(DM9000_NCR, 3); /* Issue a second reset */
+
+ do {
+ DM9000_DBG("resetting the DM9000, 2nd reset\n");
+ udelay(25); /* Wait at least 20 us */
+ } while (DM9000_ior(DM9000_NCR) & 1);
+
+ /* Check whether the ethernet controller is present */
+ if ((DM9000_ior(DM9000_PIDL) != 0x0) ||
+ (DM9000_ior(DM9000_PIDH) != 0x90))
+ printf("ERROR: resetting DM9000 -> not responding\n");
}
/* Initilize dm9000 board
--
-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2008.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users
