Dear Adam Graham,
In message <[EMAIL PROTECTED]> you wrote:
> The Arches Evaluation board is based on the AMCC 460GT SoC chip. This board
> is a dual processor board with each processor providing independent resources
> for Rapid IO, Gigabit Ethernet, and serial communications. Each 460GT has
> it's own 512MB DDR2 memory, 32MB NOR FLASH, UART, EEPROM and temperature
> sensor, along with a shared debug port. The two 460GT's will communicate
> with each other via shared memory, Gigabit Ethernet and x1 PCI-Express.
Wow. Line length 448, that's more than 6 times the allowed max.
Please restrict your line length to < 70 characters.
...
> +int misc_init_r(void)
> +{
...
> + /* reset all SGMII interfaces */
> + mfsdr(SDR0_SRST1, reg);
> + reg |= (SDR0_SRST1_SGMII0 | SDR0_SRST1_SGMII1 | SDR0_SRST1_SGMII2);
> + mtsdr(SDR0_SRST1, reg);
> + mtsdr(SDR0_ETH_STS, 0xFFFFFFFF);
> + mtsdr(SDR0_SRST1, 0x00000000);
> +
> + for (timeout = 60; timeout > 0; timeout--) {
> + udelay(1000);
> + mfsdr(SDR0_ETH_PLL, eth_pll);
> + if ((eth_pll & SDR0_ETH_PLL_PLLLOCK) != 0)
> + break;
> + }
Where is the 60 ms timeout coming from?
> --- a/include/configs/amcc-common.h
> +++ b/include/configs/amcc-common.h
> @@ -55,6 +55,13 @@
> #endif
>
> /*
> + * Only very few boards have default netdev not set to eth0 (like Arches)
> + */
> +#if !defined(CONFIG_NETDEV)
> +#define CONFIG_NETDEV eth0
> +#endif
Please don't add this to common code; please handle it locally in the
arches configuration.
> @@ -147,9 +154,11 @@
> /*
> * Booting and default environment
> */
> +#if !defined(CONFIG_PREBOOT)
> #define CONFIG_PREBOOT "echo;" \
> "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
> "echo"
> +#endif
Ditto. [Also: what's the reason for this change? ]
> + "net_self_load=tftp ${kernel_addr_r} ${bootfile};" \
> + "tftp ${fdt_addr_r} ${fdt_file};" \
> + "tftp ${ramdisk_addr_r} ${ramdisk_file};\0" \
What is this needed for?
> diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h
> index 2f162e1..acad9b3 100644
> --- a/include/configs/canyonlands.h
> +++ b/include/configs/canyonlands.h
...
> +#define CONFIG_PREBOOT \
> + "setenv ethact ppc_4xx_eth1;" \
This should not be done in the preboot command, but as part of the
default config instead.
> -#define CFG_AHB_BASE 0xE2000000 /* internal AHB peripherals
> */
> +#define CFG_AHB_BASE 0xE2000000 /* internal AHB peripherals */
Is this change an improvement?
> @@ -223,6 +268,7 @@
> * DDR SDRAM
>
> *----------------------------------------------------------------------------*/
> #if !defined(CONFIG_NAND_U_BOOT)
> +#if !defined(CONFIG_ARCHES)
> /*
> * NAND booting U-Boot version uses a fixed initialization, since the whole
> * I2C SPD DIMM autodetection/calibration doesn't fit into the 4k of boot
Are you sure this is correct?
> +#if !defined(CONFIG_ARCHES)
> /* Only Canyonlands (460EX) has USB */
> #ifdef CONFIG_460EX
I think it would make more sense to move the "!defined(CONFIG_ARCHES)"
_after_ the "#ifdef CONFIG_460EX".
> +#else /* defined(CONFIG_ARCHES) */
> +
> +/* Arches board does not have USB connectivity */
> +
> +/*
> + * Default environment variables
> + */
> +#define CONFIG_EXTRA_ENV_SETTINGS
> \
Ah... but these definitely do not belong into the "USB connectivity"
block...
> */
> +#if !defined(CONFIG_ARCHES)
> #define CONFIG_CMD_DATE
> -#define CONFIG_CMD_DTT
> #define CONFIG_CMD_NAND
> +#define CONFIG_CMD_SNTP
> +#endif
> +#define CONFIG_CMD_DTT
> #define CONFIG_CMD_PCI
> #define CONFIG_CMD_SDRAM
> -#define CONFIG_CMD_SNTP
> #ifdef CONFIG_460EX
> #define CONFIG_CMD_EXT2
> #define CONFIG_CMD_FAT
I think we should separate these tlistrs of commands, so we can keep
the lists sorted.
> +/*
> + * Arches has 32MBytes of NOR FLASH (Spansion 29GL256) so remap FLASH to
> + * EBC address which accepts bigger regions:
> + * 0xfe00.0000 -> 4.ce00.0000
> + */
Cannot we do this automatically, dependent on the actual size of flash
as determined by the code?
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: [EMAIL PROTECTED]
Q: What do you get when you cross an ethernet with an income statement?
A: A local area networth.
_______________________________________________
U-Boot mailing list
[email protected]
http://lists.denx.de/mailman/listinfo/u-boot
