I've run u-boot with all of these patches and see it working well on Beagle.
On Dec 6, 2008, at 1:00 AM, Dirk Behme wrote: > mmc_init was always returning success -- now returns failure if > no card is present. > > Signed-off-by: Steve Sakoman <[EMAIL PROTECTED]> > Signed-off-by: Dirk Behme <[EMAIL PROTECTED]> > > --- > > * This patch applies on top of last 5 pending OMAP3 patches (in this > order): > > http://lists.denx.de/pipermail/u-boot/2008-November/043771.html > http://lists.denx.de/pipermail/u-boot/2008-November/043898.html > http://lists.denx.de/pipermail/u-boot/2008-November/043899.html > http://lists.denx.de/pipermail/u-boot/2008-November/044026.html > http://lists.denx.de/pipermail/u-boot/2008-November/044027.html > > * Compile tested for Beagle, Overo, Panora and EVM. Boot tested on > Beagle. > > drivers/mmc/omap3_mmc.c | 32 ++++++++++++++++---------------- > 1 files changed, 16 insertions(+), 16 deletions(-) > > Index: u-boot-arm/drivers/mmc/omap3_mmc.c > =================================================================== > --- u-boot-arm.orig/drivers/mmc/omap3_mmc.c > +++ u-boot-arm/drivers/mmc/omap3_mmc.c > @@ -523,22 +523,22 @@ unsigned long mmc_bread(int dev_num, uns > > int mmc_init(int verbose) > { > - configure_mmc(&cur_card_data); > - > - mmc_blk_dev.if_type = IF_TYPE_MMC; > - mmc_blk_dev.part_type = PART_TYPE_DOS; > - mmc_blk_dev.dev = 0; > - mmc_blk_dev.lun = 0; > - mmc_blk_dev.type = 0; > - > - /* FIXME fill in the correct size (is set to 32MByte) */ > - mmc_blk_dev.blksz = MMCSD_SECTOR_SIZE; > - mmc_blk_dev.lba = 0x10000; > - mmc_blk_dev.removable = 0; > - mmc_blk_dev.block_read = mmc_bread; > - > - fat_register_device(&mmc_blk_dev, 1); > - return 0; > + if (configure_mmc(&cur_card_data) == 1) { > + mmc_blk_dev.if_type = IF_TYPE_MMC; > + mmc_blk_dev.part_type = PART_TYPE_DOS; > + mmc_blk_dev.dev = 0; > + mmc_blk_dev.lun = 0; > + mmc_blk_dev.type = 0; > + > + /* FIXME fill in the correct size (is set to 32MByte) */ > + mmc_blk_dev.blksz = MMCSD_SECTOR_SIZE; > + mmc_blk_dev.lba = 0x10000; > + mmc_blk_dev.removable = 0; > + mmc_blk_dev.block_read = mmc_bread; > + > + fat_register_device(&mmc_blk_dev, 1); > + return 0; > + } else return 1; > } > > int mmc_read(ulong src, uchar *dst, int size) > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
