Previously we only allowed power-of-two memory sizes and didnt handle >2G of memory. Now we will map up to CONFIG_MAX_MEM_MAPPED and should properly handle any size that we can make in the TLBs we have available to us
Signed-off-by: Kumar Gala <[email protected]> --- This depends on the following two patches: * Add an architecture specific config.h for common defines * ppc: Move CONFIG_MAX_MEM_MAPPED to common config.h cpu/mpc85xx/tlb.c | 74 +++++++++++++++--------------------------- include/asm-ppc/config.h | 5 ++- include/asm-ppc/processor.h | 2 + include/configs/MPC8572DS.h | 1 + 4 files changed, 33 insertions(+), 49 deletions(-) diff --git a/cpu/mpc85xx/tlb.c b/cpu/mpc85xx/tlb.c index 25fa9ee..c73bf05 100644 --- a/cpu/mpc85xx/tlb.c +++ b/cpu/mpc85xx/tlb.c @@ -132,61 +132,41 @@ void init_addr_map(void) unsigned int setup_ddr_tlbs(unsigned int memsize_in_meg) { unsigned int tlb_size; - unsigned int ram_tlb_index; - unsigned int ram_tlb_address; + unsigned int ram_tlb_index = CONFIG_SYS_DDR_TLB_START; + unsigned int ram_tlb_address = (unsigned int)CONFIG_SYS_DDR_SDRAM_BASE; + unsigned int max_cam = (mfspr(SPRN_TLB1CFG) >> 16) & 0xff; + u64 size, memsize = (u64)memsize_in_meg << 20; - /* - * Determine size of each TLB1 entry. - */ - switch (memsize_in_meg) { - case 16: - case 32: - tlb_size = BOOKE_PAGESZ_16M; - break; - case 64: - case 128: - tlb_size = BOOKE_PAGESZ_64M; - break; - case 256: - case 512: - tlb_size = BOOKE_PAGESZ_256M; - break; - case 1024: - case 2048: - if (PVR_VER(get_pvr()) > PVR_VER(PVR_85xx)) - tlb_size = BOOKE_PAGESZ_1G; - else - tlb_size = BOOKE_PAGESZ_256M; - break; - default: - puts("DDR: only 16M, 32M, 64M, 128M, 256M, 512M, 1G" - " and 2G are supported.\n"); - - /* - * The memory was not able to be mapped. - * Default to a small size. - */ - tlb_size = BOOKE_PAGESZ_64M; - memsize_in_meg = 64; - break; - } + size = min(memsize, CONFIG_MAX_MEM_MAPPED); + + /* Convert (4^max) kB to (2^max) bytes */ + max_cam = max_cam * 2 + 10; + + for (; size && ram_tlb_index < 16; ram_tlb_index++) { + u32 camsize = __ilog2_u64(size) & ~1U; + u32 align = __ilog2(ram_tlb_address) & ~1U; + + if (align == -2) align = max_cam; + if (camsize > align) + camsize = align; + + if (camsize > max_cam) + camsize = max_cam; + + tlb_size = (camsize - 10) / 2; - /* - * Configure DDR TLB1 entries. - * Starting at TLB1 8, use no more than 8 TLB1 entries. - */ - ram_tlb_index = CONFIG_SYS_DDR_TLB_START; - ram_tlb_address = (unsigned int)CONFIG_SYS_DDR_SDRAM_BASE; - while (ram_tlb_address < (memsize_in_meg * 1024 * 1024) - && ram_tlb_index < 16) { set_tlb(1, ram_tlb_address, ram_tlb_address, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, ram_tlb_index, tlb_size, 1); - ram_tlb_address += (0x1000 << ((tlb_size - 1) * 2)); - ram_tlb_index++; + size -= 1ULL << camsize; + memsize -= 1ULL << camsize; + ram_tlb_address += 1UL << camsize; } + if (memsize) + printf("%lldM left unmapped\n", memsize >> 20); + /* * Confirm that the requested amount of memory was mapped. */ diff --git a/include/asm-ppc/config.h b/include/asm-ppc/config.h index 6d27cb1..5640b39 100644 --- a/include/asm-ppc/config.h +++ b/include/asm-ppc/config.h @@ -22,8 +22,9 @@ #define _ASM_CONFIG_H_ #ifndef CONFIG_MAX_MEM_MAPPED -#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2) && defined(CONFIG_SPD_EEPROM) -#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)2 << 30) +#if (defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2) && defined(CONFIG_SPD_EEPROM)) || \ + defined(CONFIG_E500) +#define CONFIG_MAX_MEM_MAPPED ((phys_size_t)2u << 30) #else #define CONFIG_MAX_MEM_MAPPED (256 << 20) #endif diff --git a/include/asm-ppc/processor.h b/include/asm-ppc/processor.h index e07e5d3..4203ada 100644 --- a/include/asm-ppc/processor.h +++ b/include/asm-ppc/processor.h @@ -451,6 +451,8 @@ #define L2CSR0_L2LO 0x00000020 /* L2 Cache Lock Overflow */ #define SPRN_L2CSR1 0x3fa /* L2 Data Cache Control and Status Register 1 */ +#define SPRN_TLB0CFG 0x2B0 /* TLB 0 Config Register */ +#define SPRN_TLB1CFG 0x2B1 /* TLB 1 Config Register */ #define SPRN_MMUCSR0 0x3f4 /* MMU control and status register 0 */ #define SPRN_MAS0 0x270 /* MMU Assist Register 0 */ #define SPRN_MAS1 0x271 /* MMU Assist Register 1 */ diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h index ac0a464..a2360d8 100644 --- a/include/configs/MPC8572DS.h +++ b/include/configs/MPC8572DS.h @@ -103,6 +103,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy); /* DDR Setup */ #define CONFIG_SYS_DDR_TLB_START 9 +#define CONFIG_VERY_BIG_RAM #define CONFIG_FSL_DDR2 #undef CONFIG_FSL_DDR_INTERACTIVE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -- 1.5.6.6 _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
