On 03/19/2013 01:35 PM, Otavio Salvador wrote:
On Tue, Mar 19, 2013 at 3:52 AM, Lauri Hintsala
<lauri.hints...@bluegiga.com> wrote:
Hi,
On 03/01/2013 12:59 AM, Fabio Estevam wrote:
From: Fabio Estevam <fabio.este...@freescale.com>
Currently the following kernel hang happens when loading a 2.6.35 kernel
from
Freeescale on a mx28evk board:
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registered
mxs_cpu_init: cpufreq init finished
...
I tried to boot Freescale's 2.6.35.3 kernel on apx4devkit. The device is
still freezing after mxs_cpu_init print.
Full logs:
U-Boot 2013.04-rc1-00002-g9659479 (Mar 19 2013 - 08:30:05)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SD/MMC #0, 3V3
I2C: ready
DRAM: 64 MiB
NAND: 128 MiB
MMC: MXS MMC: 0
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
1944456 bytes read in 754 ms (2.5 MiB/s)
## Booting kernel from Legacy Image at 41000000 ...
Image Name: Linux-2.6.35.3-01010-ge53a812
Created: 2013-03-19 6:31:40 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1944392 Bytes = 1.9 MiB
Load Address: 40008000
Entry Point: 40008000
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.35.3-01010-ge53a812 (hintsla@bgtlh) (gcc version 4.3.4
(crosstool-NG-1.7.0) ) #32 Tue Mar 19 08:31:39 EET 2013
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Freescale MX28EVK board
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=tty0 console=ttyAMA0,115200 consoleblank=0
ethaddr=00:07:80:01:66:db btaddr=00:07:80:01:67:0d
wlanaddr=00:07:80:59:ef:64 root=/dev/mmcblk0p2 rootwait
mtdparts=gpmi-nand:128k(bootstrap),1024k(boot),768k(env),-(root) rw
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60880k/60880k available, 4656k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xfde00000 - 0xffe00000 ( 32 MB)
vmalloc : 0xc4800000 - 0xf0000000 ( 696 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc002d000 ( 148 kB)
.text : 0xc002d000 - 0xc03b8000 (3628 kB)
.data : 0xc03b8000 - 0xc03e4ba0 ( 179 kB)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:288
Console: colour dummy device 80x30
console [tty0] enabled
console [ttyAMA0] enabled
Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal
regulator: vdddbo: 800 <--> 1575 mV fast normal
regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal
vddio = 3380000, val=10
regulator: vddio: 2880 <--> 3680 mV at 3380 mV fast normal
regulator: overall_current: fast normal
regulator: vbus5v:
regulator: mxs-duart-1: fast normal
regulator: mxs-bl-1: fast normal
regulator: mxs-i2c-1: fast normal
regulator: mmc_ssp-1: fast normal
regulator: mmc_ssp-2: fast normal
regulator: charger-1: fast normal
regulator: power-test-1: fast normal
regulator: cpufreq-1: fast normal
i.MX IRAM pool: 124 KB@0xc4820000
Initializing GPMI pins
Initializing SSP2 pins
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Version 1.0.23.
IMX usb wakeup probe
usb DR wakeup device is registered
Switching to clocksource mxs clock source
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Switched to NOHz mode on CPU #0
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Bus freq driver module loaded
IMX usb wakeup probe
usb h1 wakeup device is registered
WARNING : No battery connected !
Aborting power driver initialization
mxs-battery: probe of mxs-battery.0 failed with error 1
mxs_cpu_init: cpufreq init finished
And after that line the device is completely dead.
Are you sure you booted it with the Fabio's patch applied; this is
exactly how it behaves *without* it.
Yes, I am. I booted up U-Boot version "2013.04-rc1-00002-g9659479 (Mar
19 2013 - 08:30:05)" and my git log says:
$ git log --oneline -3
9659479 (HEAD) mxs: spl_mem_init: Align DDR2 init with FSL bootlets source
7ddcf4c ARM: mxs: disable battery charger circuit
2536850 (tag: v2013.04-rc1) Prepare v2013.04-rc1
Battery charger patch is very simple and it shouldn't affect to this
problem any way:
--- a/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c
+++ b/arch/arm/cpu/arm926ejs/mxs/spl_power_init.c
@@ -918,6 +918,9 @@ void mxs_power_init(void)
writel(POWER_5VCTRL_PWDN_5VBRNOUT,
&power_regs->hw_power_5vctrl_set);
+ /* Disable battery charger circuit */
+ power_regs->hw_power_charge_set = POWER_CHARGE_PWD_BATTCHRG;
+
early_delay(1000);
}
Lauri
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
