This patch provides support to program a flash bank address register. extended/bank address register contains an information to access the 4th byte addressing in 3-byte address mode.
Currently added an bank address register writing support for spansion flashes. reff' the spec for more details about bank addr register in Page-63, Table 8.16 http://www.spansion.com/Support/Datasheets/S25FL128S_256S_00.pdf Signed-off-by: Jagannadha Sutradharudu Teki <[email protected]> --- Changes for v2: - none drivers/mtd/spi/spi_flash.c | 37 ++++++++++++++++++++++++++++++++++++ drivers/mtd/spi/spi_flash_internal.h | 6 ++++++ include/spi_flash.h | 2 ++ 3 files changed, 45 insertions(+) diff --git a/drivers/mtd/spi/spi_flash.c b/drivers/mtd/spi/spi_flash.c index 0e38f59..7aba520 100644 --- a/drivers/mtd/spi/spi_flash.c +++ b/drivers/mtd/spi/spi_flash.c @@ -278,6 +278,40 @@ int spi_flash_cmd_write_status(struct spi_flash *flash, u8 sr) return 0; } +int spi_flash_cmd_bankaddr_write(struct spi_flash *flash, u8 bank_sel) +{ + u8 cmd, idcode0; + int ret; + + idcode0 = flash->idcode0; + if (idcode0 == 0x01) { + cmd = CMD_BANKADDR_BRWR; + } else { + printf("SF: Unsupported bank addr write %02x\n", idcode0); + return -1; + } + + ret = spi_flash_cmd_write_enable(flash); + if (ret < 0) { + debug("SF: enabling write failed\n"); + return ret; + } + + ret = spi_flash_cmd_write(flash->spi, &cmd, 1, &bank_sel, 1); + if (ret) { + debug("SF: fail to write bank addr register\n"); + return ret; + } + + ret = spi_flash_cmd_wait_ready(flash, SPI_FLASH_PROG_TIMEOUT); + if (ret < 0) { + debug("SF: write bank addr register timed out\n"); + return ret; + } + + return 0; +} + #ifdef CONFIG_OF_CONTROL int spi_flash_decode_fdt(const void *blob, struct spi_flash *flash) { @@ -422,6 +456,9 @@ struct spi_flash *spi_flash_probe(unsigned int bus, unsigned int cs, goto err_manufacturer_probe; } + /* store the manuf id, for performing specific flash ops */ + flash->idcode0 = *idp; + #ifdef CONFIG_OF_CONTROL if (spi_flash_decode_fdt(gd->fdt_blob, flash)) { debug("SF: FDT decode error\n"); diff --git a/drivers/mtd/spi/spi_flash_internal.h b/drivers/mtd/spi/spi_flash_internal.h index 141cfa8..6e38494 100644 --- a/drivers/mtd/spi/spi_flash_internal.h +++ b/drivers/mtd/spi/spi_flash_internal.h @@ -28,6 +28,9 @@ #define CMD_ERASE_64K 0xd8 #define CMD_ERASE_CHIP 0xc7 +/* Bank addr acess commands */ +#define CMD_BANKADDR_BRWR 0x17 + /* Common status */ #define STATUS_WIP 0x01 @@ -77,6 +80,9 @@ static inline int spi_flash_cmd_write_disable(struct spi_flash *flash) /* Program the status register. */ int spi_flash_cmd_write_status(struct spi_flash *flash, u8 sr); +/* Program the bank address register */ +int spi_flash_cmd_bankaddr_write(struct spi_flash *flash, u8 bank_sel); + /* * Same as spi_flash_cmd_read() except it also claims/releases the SPI * bus. Used as common part of the ->read() operation. diff --git a/include/spi_flash.h b/include/spi_flash.h index 3b6a44e..5ea42e1 100644 --- a/include/spi_flash.h +++ b/include/spi_flash.h @@ -38,6 +38,8 @@ struct spi_flash { u32 page_size; /* Erase (sector) size */ u32 sector_size; + /* ID code0 */ + u8 idcode0; void *memory_map; /* Address of read-only SPI flash access */ int (*read)(struct spi_flash *flash, u32 offset, -- 1.8.3 _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
