From: Jason Jin <jason....@freescale.com>
T1042 has internal display interface unit (DIU) for driving video.
T1042RDB supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used
as HDMI connector on T1042RDB.
This patch add support to
-enable Video interface for T1042RDB
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1042
-program HDMI encoder via I2C on board
This patch refer to the upstream diu patch
(337b0c52b3296f371d04aef71a833e09110e0e6b) for T1040qds.
Signed-off-by: Jason Jin <jason....@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.w...@freescale.com>
---
V2:
- Restore CONFIG_SYS_CONSOLE_IS_IN_ENV macors.
- Restore CONFIG_SYS_MALLOC_LEN macors, this macors not effect FB.
- Add a blank line between declarations and code.
diff --git a/board/freescale/t104xrdb/Makefile
b/board/freescale/t104xrdb/Makefile
index af38d9f..f15a633 100644
--- a/board/freescale/t104xrdb/Makefile
+++ b/board/freescale/t104xrdb/Makefile
@@ -12,3 +12,4 @@ obj-$(CONFIG_PCI) += pci.o
obj-y += law.o
obj-y += tlb.o
obj-y += cpld.o
+obj-$(CONFIG_FSL_DIU_FB) += diu.o
diff --git a/board/freescale/t104xrdb/diu.c b/board/freescale/t104xrdb/diu.c
new file mode 100644
index 0000000..3285bef
--- /dev/null
+++ b/board/freescale/t104xrdb/diu.c
@@ -0,0 +1,84 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ * Author: Priyanka Jain <priyanka.j...@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/io.h>
+#include <common.h>
+#include <command.h>
+#include <fsl_diu_fb.h>
+#include <linux/ctype.h>
+#include <video_fb.h>
+
+#include "../common/diu_ch7301.h"
+
+#include "cpld.h"
+#include "t104xrdb.h"
+
+/*
+ * DIU Area Descriptor
+ *
+ * Note that we need to byte-swap the value before it's written to the AD
+ * register. So even though the registers don't look like they're in the same
+ * bit positions as they are on the MPC8610, the same value is written to the
+ * AD register on the MPC8610 and on the P1022.
+ */
+#define AD_BYTE_F 0x10000000
+#define AD_ALPHA_C_SHIFT 25
+#define AD_BLUE_C_SHIFT 23
+#define AD_GREEN_C_SHIFT 21
+#define AD_RED_C_SHIFT 19
+#define AD_PIXEL_S_SHIFT 16
+#define AD_COMP_3_SHIFT 12
+#define AD_COMP_2_SHIFT 8
+#define AD_COMP_1_SHIFT 4
+#define AD_COMP_0_SHIFT 0
+
+void diu_set_pixel_clock(unsigned int pixclock)
+{
+ unsigned long speed_ccb, temp;
+ u32 pixval;
+ int ret;
+
+ speed_ccb = get_bus_freq(0);
+ temp = 1000000000 / pixclock;
+ temp *= 1000;
+ pixval = speed_ccb / temp;
+
+ /* Program HDMI encoder */
+ ret = diu_set_dvi_encoder(temp);
+ if (ret) {
+ puts("Failed to set DVI encoder\n");
+ return;
+ }
+
+ /* Program pixel clock */
+ out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR,
+ ((pixval << PXCK_BITS_START) & PXCK_MASK));
+
+ /* enable clock*/
+ out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR, PXCKEN_MASK |
+ ((pixval << PXCK_BITS_START) & PXCK_MASK));
+}
+
+int platform_diu_init(unsigned int xres, unsigned int yres, const char *port)
+{
+ u32 pixel_format;
+ u8 sw;
+
+ /*Configure Display ouput port as HDMI*/
+ sw = CPLD_READ(sfp_ctl_status);
+ CPLD_WRITE(sfp_ctl_status , sw & ~(CPLD_DIU_SEL_DFP));
+
+ pixel_format = cpu_to_le32(AD_BYTE_F | (3 << AD_ALPHA_C_SHIFT) |
+ (0 << AD_BLUE_C_SHIFT) | (1 << AD_GREEN_C_SHIFT) |
+ (2 << AD_RED_C_SHIFT) | (8 << AD_COMP_3_SHIFT) |
+ (8 << AD_COMP_2_SHIFT) | (8 << AD_COMP_1_SHIFT) |
+ (8 << AD_COMP_0_SHIFT) | (3 << AD_PIXEL_S_SHIFT));
+
+ printf("DIU: Switching to monitor DVI @ %ux%u\n", xres, yres);
+
+ return fsl_diu_init(xres, yres, pixel_format, 0);
+}
diff --git a/include/configs/T1042RDB_PI.h b/include/configs/T1042RDB_PI.h
index 8a8a2ff..6d3822d 100644
--- a/include/configs/T1042RDB_PI.h
+++ b/include/configs/T1042RDB_PI.h
@@ -203,6 +203,7 @@
#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK0 */
#define CPLD_LBMAP_RESET 0xFF
#define CPLD_LBMAP_SHIFT 0x03
+#define CPLD_DIU_SEL_DFP 0x80
#define CONFIG_SYS_CPLD_BASE 0xffdf0000
#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
@@ -358,6 +359,22 @@
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+/* Video */
+#define CONFIG_FSL_DIU_FB
+
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_FSL_DIU_CH7301
+#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000)
+#define CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_CFB_CONSOLE_ANSI
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#endif
+
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
@@ -380,6 +397,10 @@
/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR 0x70
+/* LDI/DVI Encoder for display */
+#define CONFIG_SYS_I2C_LDI_ADDR 0x38
+#define CONFIG_SYS_I2C_DVI_ADDR 0x75
+
/*
* RTC configuration
*/
@@ -646,6 +667,7 @@
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
"netdev=eth0\0" \
+ "video-mode=fslfb:1024x768-32@60,monitor=dvi\0" \
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
"tftpflash=tftpboot $loadaddr $uboot && " \
--
1.8.5
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
