- update readme. - add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315 ucode from NOR/NAND/SPI/SD/REMOTE. - update cpld vbank with SW3[5:7]=000 as default vbank0 instead of previous SW3[5:7]=111 as default vbank.
Signed-off-by: Shengzhou Liu <[email protected]> --- board/freescale/t208xrdb/README | 6 +++--- board/freescale/t208xrdb/cpld.h | 4 ++-- board/freescale/t208xrdb/t208xrdb.c | 2 +- include/configs/T208xRDB.h | 5 +++++ 4 files changed, 11 insertions(+), 6 deletions(-) diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README index eb9b780..ed3a18c 100644 --- a/board/freescale/t208xrdb/README +++ b/board/freescale/t208xrdb/README @@ -67,7 +67,7 @@ T2080PCIe-RDB board Overview - One PCIe x2 end-point device (C293 Crypto co-processor) - IFC/Local Bus - NOR: 128MB 16-bit NOR Flash - - NAND: 512MB 8-bit NAND flash + - NAND: 1GB 8-bit NAND flash - CPLD: for system controlling with programable header on-board - SATA - Two SATA 2.0 onnectors on-board @@ -156,11 +156,11 @@ Software configurations and board settings Switching between default bank and alternate bank on NOR flash To change boot source to vbank4: via software: run command 'cpld reset altbank' in u-boot. - via DIP-switch: set SW3[5:7] = '011' + via DIP-switch: set SW3[5:7] = '100' To change boot source to vbank0: via software: run command 'cpld reset' in u-boot. - via DIP-Switch: set SW3[5:7] = '111' + via DIP-Switch: set SW3[5:7] = '000' 2. NAND Boot: a. build PBL image for NAND boot diff --git a/board/freescale/t208xrdb/cpld.h b/board/freescale/t208xrdb/cpld.h index 4cee4e5..3f15338 100644 --- a/board/freescale/t208xrdb/cpld.h +++ b/board/freescale/t208xrdb/cpld.h @@ -35,8 +35,8 @@ void cpld_write(unsigned int reg, u8 value); #define CPLD_LBMAP_MASK 0x3F #define CPLD_BANK_SEL_MASK 0x07 #define CPLD_BANK_OVERRIDE 0x40 -#define CPLD_LBMAP_ALTBANK 0x43 /* BANK OR | BANK 4 */ -#define CPLD_LBMAP_DFLTBANK 0x47 /* BANK OR | BANK 0 */ +#define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */ +#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK 0 */ #define CPLD_LBMAP_RESET 0xFF #define CPLD_LBMAP_SHIFT 0x03 #define CPLD_BOOT_SEL 0x80 diff --git a/board/freescale/t208xrdb/t208xrdb.c b/board/freescale/t208xrdb/t208xrdb.c index f3fec2a..265c1f9 100644 --- a/board/freescale/t208xrdb/t208xrdb.c +++ b/board/freescale/t208xrdb/t208xrdb.c @@ -44,7 +44,7 @@ int checkboard(void) puts("NAND\n"); } else { reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT); - printf("NOR vBank%d\n", ~reg & 0x7); + printf("NOR vBank%d\n", reg); } #endif diff --git a/include/configs/T208xRDB.h b/include/configs/T208xRDB.h index aacc8b7..a09484d 100644 --- a/include/configs/T208xRDB.h +++ b/include/configs/T208xRDB.h @@ -584,6 +584,7 @@ unsigned long get_board_ddr_clk(void); * env, so we got 0x110000. */ #define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH #define CONFIG_SYS_QE_FMAN_FW_ADDR 0x110000 #define CONFIG_CORTINA_FW_ADDR 0x120000 @@ -594,11 +595,13 @@ unsigned long get_board_ddr_clk(void); * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080. */ #define CONFIG_SYS_QE_FMAN_FW_IN_MMC +#define CONFIG_SYS_CORTINA_FW_IN_MMC #define CONFIG_SYS_QE_FMAN_FW_ADDR (512 * 0x820) #define CONFIG_CORTINA_FW_ADDR (512 * 0x8a0) #elif defined(CONFIG_NAND) #define CONFIG_SYS_QE_FMAN_FW_IN_NAND +#define CONFIG_SYS_CORTINA_FW_IN_NAND #define CONFIG_SYS_QE_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE) #define CONFIG_CORTINA_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE) #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) @@ -610,10 +613,12 @@ unsigned long get_board_ddr_clk(void); * master LAW->the ucode address in master's memory space. */ #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE +#define CONFIG_SYS_CORTINA_FW_IN_REMOTE #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 #define CONFIG_CORTINA_FW_ADDR 0xFFE10000 #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_CORTINA_FW_IN_NOR #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF00000 #define CONFIG_CORTINA_FW_ADDR 0xEFE00000 #endif -- 1.8.0 _______________________________________________ U-Boot mailing list [email protected] http://lists.denx.de/mailman/listinfo/u-boot
