Hello Bo,
Am 29.12.2014 08:53, schrieb Bo Shen:
Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.
As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM. So, we need to initialize the SDRAM as soon
as possible. Borrow the low level init code from
<arm/arm/cpu/armv7/lowlevel_init.S> for this purpose.
Signed-off-by: Bo Shen <voice.s...@atmel.com>
---
arch/arm/Kconfig | 1 +
arch/arm/cpu/arm926ejs/at91/Makefile | 4 ++
arch/arm/cpu/arm926ejs/at91/spl_lowlevel_init.S | 37 ++++++++++++
arch/arm/cpu/at91-common/spl_at91.c | 10 ++++
arch/arm/cpu/at91-common/u-boot-spl-arm9.lds | 48 +++++++++++++++
board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 80 +++++++++++++++++++++++++
configs/at91sam9m10g45ek_mmc_defconfig | 5 +-
configs/at91sam9m10g45ek_nandflash_defconfig | 5 +-
include/configs/at91sam9m10g45ek.h | 64 ++++++++++++++++++++
9 files changed, 250 insertions(+), 4 deletions(-)
create mode 100644 arch/arm/cpu/arm926ejs/at91/spl_lowlevel_init.S
create mode 100644 arch/arm/cpu/at91-common/u-boot-spl-arm9.lds
[...]
diff --git a/arch/arm/cpu/arm926ejs/at91/spl_lowlevel_init.S
b/arch/arm/cpu/arm926ejs/at91/spl_lowlevel_init.S
new file mode 100644
index 0000000..f1b2ec9
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/at91/spl_lowlevel_init.S
@@ -0,0 +1,37 @@
+/*
+ * A lowlevel_init function that sets up the stack to call a C function to
+ * perform further init.
+ *
+ * (C) Copyright 2010
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ * Aneesh V <ane...@ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <config.h>
+#include <linux/linkage.h>
+
+ENTRY(lowlevel_init)
+ /*
+ * Setup a temporary stack
+ */
+ ldr sp, =CONFIG_SYS_INIT_SP_ADDR
+ bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
+
+ ldr r9, =gdata
+
+ /*
+ * Save the old lr(passed in ip) and the current lr to stack
+ */
+ push {ip, lr}
+
+ /*
+ * go setup pll, mux, memory
+ */
+ bl s_init
+ pop {ip, pc}
+ENDPROC(lowlevel_init)
Hmm ... we have SPL support for at91sam9* boards without
such a file in U-Boot (and without an
arch/arm/cpu/at91-common/u-boot-spl-arm9.lds),
see for example:
http://git.denx.de/?p=u-boot.git;a=blob;f=configs/corvus_defconfig;h=5d60847523487cac5e2e9421d9e6c6ff3fa2ce9e;hb=b7b3b8c6a0bfc87047cb18a7abfa06fb6e9d0331
The "spl_board_init" is called from ./common/spl/spl.c
from "board_init_r" which is called from "board_init_f"
in ./arch/arm/lib/spl.c, which is called from
./arch/arm/lib/crt0.S
Is this new file really needed? It should possible to remove
CONFIG_SKIP_LOWLEVEL_INIT
in include/configs/at91sam9m10g45ek.h ...
diff --git a/arch/arm/cpu/at91-common/spl_at91.c
b/arch/arm/cpu/at91-common/spl_at91.c
index 89f588b..f044117 100644
--- a/arch/arm/cpu/at91-common/spl_at91.c
+++ b/arch/arm/cpu/at91-common/spl_at91.c
@@ -71,7 +71,17 @@ void __weak at91_spl_board_init(void)
{
}
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+__weak void spl_board_init(void)
+{
+}
+#endif
+
+#ifdef CONFIG_SKIP_LOWLEVEL_INIT
void spl_board_init(void)
+#else
+void s_init(void)
+#endif
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
... and adding this "ifdefs" could be prevented ...
What do you think?
Ah! you wrote:
> As the boot from SD/MMC card with FAT file system, the BSS
> segment is too big to fit into SRAM, so, use the lds to put
> it into SDRAM. So, we need to initialize the SDRAM as soon
> as possible. Borrow the low level init code from
> <arm/arm/cpu/armv7/lowlevel_init.S> for this purpose.
Hmm... maybe we can include this in the existing code? So we
have BSS for all at91 boards in RAM?
Or, if not possible, we should convert the existing boards into
your framework ... if you can prepare such a patch I can test it
on the corvus, taurus and axm boards ...
bye,
Heiko
diff --git a/arch/arm/cpu/at91-common/u-boot-spl-arm9.lds
b/arch/arm/cpu/at91-common/u-boot-spl-arm9.lds
new file mode 100644
index 0000000..6f350a9
--- /dev/null
+++ b/arch/arm/cpu/at91-common/u-boot-spl-arm9.lds
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2014 Atmel Corporation
+ * Bo Shen <voice.s...@atmel.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE, \
+ LENGTH = CONFIG_SPL_MAX_SIZE }
+MEMORY { .sdram : ORIGIN = CONFIG_SPL_BSS_START_ADDR, \
+ LENGTH = CONFIG_SPL_BSS_MAX_SIZE }
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ .text :
+ {
+ __start = .;
+ *(.vectors)
+ arch/arm/cpu/arm926ejs/start.o (.text*)
+ *(.text*)
+ } >.sram
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram
+
+ . = ALIGN(4);
+ .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
+
+ . = ALIGN(4);
+ __image_copy_end = .;
+
+ .end :
+ {
+ *(.__end)
+ } >.sram
+
+ .bss :
+ {
+ . = ALIGN(4);
+ __bss_start = .;
+ *(.bss*)
+ . = ALIGN(4);
+ __bss_end = .;
+ } >.sdram
+}
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
index b807ef9..4289179 100644
--- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
+++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
@@ -8,6 +8,7 @@
#include <common.h>
#include <asm/io.h>
+#include <asm/arch/clk.h>
#include <asm/arch/at91sam9g45_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
@@ -15,6 +16,7 @@
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <lcd.h>
+#include <linux/mtd/nand.h>
#include <atmel_lcdc.h>
#include <atmel_mci.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
@@ -71,6 +73,84 @@ void at91sam9m10g45ek_nand_hw_init(void)
}
#endif
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+ /*
+ * On the at91sam9m10g45ek board, the chip wm9711 stays in the
+ * test mode, so it needs do some action to exit test mode.
+ */
+ at91_periph_clk_enable(ATMEL_ID_PIODE);
+ at91_set_gpio_output(AT91_PIN_PD7, 0);
+ at91_set_gpio_output(AT91_PIN_PD8, 0);
+ at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1);
+ at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1);
+
+#ifdef CONFIG_SYS_USE_MMC
+ at91_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+ at91sam9m10g45ek_nand_hw_init();
+#endif
+}
+
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddr *ddr2)
+{
+ ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+ ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+ ATMEL_MPDDRC_CR_NR_ROW_14 |
+ ATMEL_MPDDRC_CR_DQMS_SHARED |
+ ATMEL_MPDDRC_CR_CAS_DDR_CAS3);
+
+ ddr2->rtr = 0x24b;
+
+ ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
+ 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */
+ 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
+ 1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
+ 1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
+ 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */
+
+ ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
+ 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+ 16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+ 14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+ ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+ 0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+ 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+ 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+ struct atmel_mpddr ddr2;
+ unsigned long csa;
+
+ ddr2_conf(&ddr2);
+
+ /* enable DDR2 clock */
+ writel(0x4, &pmc->scer);
+
+ /* Chip select 1 is for DDR2/SDRAM */
+ csa = readl(&mat->ebicsa);
+ csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
+ csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V;
+ writel(csa, &mat->ebicsa);
+
+ /* DDRAM2 Controller initialize */
+ ddr2_init(ATMEL_BASE_CS6, &ddr2);
+}
+#endif
+
#ifdef CONFIG_CMD_USB
static void at91sam9m10g45ek_usb_hw_init(void)
{
diff --git a/configs/at91sam9m10g45ek_mmc_defconfig
b/configs/at91sam9m10g45ek_mmc_defconfig
index 1681bc8..30d632d 100644
--- a/configs/at91sam9m10g45ek_mmc_defconfig
+++ b/configs/at91sam9m10g45ek_mmc_defconfig
@@ -1,3 +1,4 @@
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_MMC"
-CONFIG_ARM=y
-CONFIG_TARGET_AT91SAM9M10G45EK=y
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_AT91SAM9M10G45EK=y
diff --git a/configs/at91sam9m10g45ek_nandflash_defconfig
b/configs/at91sam9m10g45ek_nandflash_defconfig
index 61ae56e..b3de8a1 100644
--- a/configs/at91sam9m10g45ek_nandflash_defconfig
+++ b/configs/at91sam9m10g45ek_nandflash_defconfig
@@ -1,3 +1,4 @@
+CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_NANDFLASH"
-CONFIG_ARM=y
-CONFIG_TARGET_AT91SAM9M10G45EK=y
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_AT91SAM9M10G45EK=y
diff --git a/include/configs/at91sam9m10g45ek.h
b/include/configs/at91sam9m10g45ek.h
index db5d5ea..cb9a8f0 100644
--- a/include/configs/at91sam9m10g45ek.h
+++ b/include/configs/at91sam9m10g45ek.h
@@ -26,7 +26,9 @@
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
+#ifndef CONFIG_SPL_BUILD
#define CONFIG_SKIP_LOWLEVEL_INIT
+#endif
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_DISPLAY_CPUINFO
@@ -98,8 +100,12 @@
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS6
#define CONFIG_SYS_SDRAM_SIZE 0x08000000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_INIT_SP_ADDR 0x310000
+#else
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
+#endif
/* NAND flash */
#ifdef CONFIG_CMD_NAND
@@ -203,4 +209,62 @@
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024,
0x1000)
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x300000
+#define CONFIG_SPL_MAX_SIZE 0x010000
+
+#define CONFIG_SPL_BSS_START_ADDR 0x70000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
+#define CONFIG_SYS_SPL_MALLOC_START 0x70080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SYS_MONITOR_LEN 0x80000
+
+#ifdef CONFIG_SYS_USE_MMC
+#define CONFIG_SPL_LDSCRIPT
arch/arm/cpu/at91-common/u-boot-spl-arm9.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+
+#elif CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14)
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SOFTECC
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
+ 48, 49, 50, 51, 52, 53, 54, 55, \
+ 56, 57, 58, 59, 60, 61, 62, 63, }
+#endif
+
+#define CONFIG_SPL_ATMEL_SIZE
+#define CONFIG_SYS_MASTER_CLOCK 132096000
+#define CONFIG_SYS_AT91_PLLA 0x20c73f03
+#define CONFIG_SYS_MCKR 0x1301
+#define CONFIG_SYS_MCKR_CSS 0x1302
+
+#define ATMEL_BASE_MPDDRC ATMEL_BASE_DDRSDRC0
#endif
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
