This patch configures and initializes the L2 switch on T1040rdb board.
The external L2 switch ports may be connected to PHYs only over
QSGMII, for T1040rdb.
Signed-off-by: Codrin Ciubotariu <codrin.ciubota...@freescale.com>
---
Changes for v2: None
Changed for v3:
- Removed "Change-id" line from comment;
board/freescale/t104xrdb/eth.c | 50 ++++++++++++++++++++++++++++++++++++++++++
include/configs/T104xRDB.h | 6 +++++
2 files changed, 56 insertions(+)
diff --git a/board/freescale/t104xrdb/eth.c b/board/freescale/t104xrdb/eth.c
index f5c0ec8..7581a4cd 100644
--- a/board/freescale/t104xrdb/eth.c
+++ b/board/freescale/t104xrdb/eth.c
@@ -6,11 +6,13 @@
#include <common.h>
#include <netdev.h>
+#include <asm/fsl_serdes.h>
#include <asm/immap_85xx.h>
#include <fm_eth.h>
#include <fsl_mdio.h>
#include <malloc.h>
#include <asm/fsl_dtsec.h>
+#include <vsc9953.h>
#include "../common/fman.h"
@@ -20,6 +22,11 @@ int board_eth_init(bd_t *bis)
struct memac_mdio_info memac_mdio_info;
unsigned int i;
int phy_addr = 0;
+#ifdef CONFIG_VSC9953
+ phy_interface_t phy_int;
+ struct mii_dev *bus;
+#endif
+
printf("Initializing Fman\n");
memac_mdio_info.regs =
@@ -81,6 +88,49 @@ int board_eth_init(bd_t *bis)
DEFAULT_FM_MDIO_NAME));
}
+#ifdef CONFIG_VSC9953
+ /* SerDes configured for QSGMII */
+ if (serdes_get_first_lane(FSL_SRDS_1, QSGMII_SW1_A) >= 0) {
+ for (i = 0; i < 4; i++) {
+ bus = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+ phy_addr = CONFIG_SYS_FM1_QSGMII11_PHY_ADDR + i;
+ phy_int = PHY_INTERFACE_MODE_QSGMII;
+
+ vsc9953_port_info_set_mdio(i, bus);
+ vsc9953_port_info_set_phy_address(i, phy_addr);
+ vsc9953_port_info_set_phy_int(i, phy_int);
+ vsc9953_port_enable(i);
+ }
+ }
+ if (serdes_get_first_lane(FSL_SRDS_1, QSGMII_SW1_B) >= 0) {
+ for (i = 4; i < 8; i++) {
+ bus = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+ phy_addr = CONFIG_SYS_FM1_QSGMII21_PHY_ADDR + i - 4;
+ phy_int = PHY_INTERFACE_MODE_QSGMII;
+
+ vsc9953_port_info_set_mdio(i, bus);
+ vsc9953_port_info_set_phy_address(i, phy_addr);
+ vsc9953_port_info_set_phy_int(i, phy_int);
+ vsc9953_port_enable(i);
+ }
+ }
+
+ /* Connect DTSEC1 to L2 switch if it doesn't have a PHY */
+ if (serdes_get_first_lane(FSL_SRDS_1, SGMII_FM1_DTSEC1) < 0)
+ vsc9953_port_enable(8);
+
+ /* Connect DTSEC2 to L2 switch if it doesn't have a PHY */
+ if (serdes_get_first_lane(FSL_SRDS_1, SGMII_FM1_DTSEC2) < 0) {
+ /* Enable L2 On MAC2 using SCFG */
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)
+ CONFIG_SYS_MPC85xx_SCFG;
+
+ out_be32(&scfg->esgmiiselcr, in_be32(&scfg->esgmiiselcr) |
+ (0x80000000));
+ vsc9953_port_enable(9);
+ }
+#endif
+
cpu_eth_init(bis);
#endif
diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h
index 57cdf72..c77b5d5 100644
--- a/include/configs/T104xRDB.h
+++ b/include/configs/T104xRDB.h
@@ -726,6 +726,12 @@
#define CONFIG_SYS_RGMII1_PHY_ADDR 0x01
#define CONFIG_SYS_RGMII2_PHY_ADDR 0x02
+#ifdef CONFIG_T1040RDB
+#define CONFIG_VSC9953_CMD
+#define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR 0x04
+#define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR 0x08
+#endif
+
#define CONFIG_MII /* MII PHY management */
#define CONFIG_ETHPRIME "FM1@DTSEC4"
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
--
1.7.11.7
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
